Study guide
2.6 Hipot Testing Safety & Post-Hipot Grounding
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
2.6 Hipot Testing Safety & Post-Hipot Grounding
Key Takeaways Explain This Topic AI
DC hipot procedure: isolate the cable/equipment, discharge residual charge through a resistor, barricade and sign the area, connect the test set ground, then ramp voltage gradually per ANSI/NETA
After each overpotential test the specimen must be discharged through a resistor and then solidly grounded for at least 4× the test duration to release dielectric absorption charge
An isolation transformer separates the DC test set's grounded return from the source neutral, preventing unwanted current through the source-system ground and eliminating shock risk from capacitive coupling
Before trip-testing a relay to an in-service breaker, rack out the breaker or isolate the trip circuit to prevent an unintended system outage; notify the system operator
Trip-test isolation, a two-person rule, and physical guarding (barriers, signs) of the test area are required; never leave a hipot set unattended while energized
Last updated: August 2026
The Hipot Test Procedure
A hipot (high-potential) test applies a voltage above the equipment's rated voltage to stress the insulation and find defects. DC hipot is commonly used on medium-voltage cable; AC hipot and very-low-frequency (VLF) tests are used per ANSI/NETA standards. Because the test voltage can be tens of kV, the safety procedure is rigid:
Isolate the cable or equipment from all other equipment and from the system. Disconnect both ends; do not hipot through a transformer or a switchgear bus unless the test is specifically designed for it.
Discharge residual charge through a resistor. Even a cable that has been de-energized for hours can hold charge in its capacitance. Use a grounded discharge stick with a series resistor to limit the discharge current; never short the conductor directly to ground with an uninsulated tool.
Barricade and sign the test area. Erect physical barriers, post high-voltage warning signs, and control access. The area must be large enough to keep all non-essential personnel outside the arc-flash and shock boundaries.
Connect the test set ground. The hipot set's ground lead is connected to the station ground grid first and remains connected throughout the test.
Ramp the voltage gradually per ANSI/NETA. Apply the test voltage in steps, hold at each level, and record leakage current. Do not apply full test voltage instantaneously — a sudden application can damage good insulation and produces a large inrush current into the cable capacitance.
After the test , ramp the voltage down, discharge the specimen through a resistor, then solidly ground the specimen (see Post-Hipot Grounding below).
Exam trap: "Skip safety grounds" and "leave cable ends exposed in the walkway" are common wrong-answer distractors on NETA items. The test leads and cable ends must be guarded and clear of the walkway; safety grounds are required before and after the test.
Post-Hipot Grounding — The 4× Rule
DC testing leaves charge in the cable's capacitance and in the dielectric absorption (polarization) of the insulation. Even after the test voltage is removed and the initial discharge is done, the dielectric slowly releases additional charge over minutes or hours. If the cable is left ungrounded, this released charge can rebuild a dangerous voltage on the conductor.
The industry rule is to ground the specimen solidly for at least four times the test duration after each overpotential test. For example, a 10-minute DC hipot test requires a 40-minute post-test ground. The grounding discharges both the geometric capacitance and the dielectric absorption charge. The ground is left in place until the next test or until the cable is returned to service.
Discharge is always done through a resistor first (to limit the discharge current and avoid a high-current arc at the grounding point), and then a solid (low-resistance) ground is applied for the 4× hold.
The Isolation Transformer
A step-up isolation transformer is used with some DC hipot sets to separate the test set's grounded return from the source-side neutral. Without isolation, the test set's return current can flow through the source-system ground grid, tripping ground-fault relays on the source system or creating unwanted current paths through the station ground. The isolation transformer floats the test set's return so that all test current returns through the test set's own ground lead, not through the source system.
An additional benefit is shock protection: the isolation transformer eliminates the capacitive coupling between the test set and the source neutral that can put a voltage on the test set frame. For floating-ground tests (e.g., testing a cable with no station ground reference available), the isolation transformer is essential.
Trip-Test Isolation
A different but related safety rule applies to relay trip testing . Before bump-testing a relay and its output contacts to the breaker, the technician must first rack out the breaker or isolate the trip circuit . Otherwise, an unexpected trip signal will trip the in-service breaker and cause an outage to the system. Always notify the system operator/owner and follow the work permit process before any trip test. This rule is independent of the hipot safety procedure but is commonly grouped with it because both involve testing that can affect the power system.
Two-Person Rule and Guarding
NETA safety practice requires a two-person rule for hipot testing: one person operates the test set, the other observes the test area and the specimen for problems (a flashover, a broken lead, an unauthorized person approaching). The observer is positioned outside the hazard zone but with a clear line of sight and a means to shut down the test set immediately. The test area is physically guarded with barriers, signs, and (where possible) interlocked gates that de-energize the test set if opened. The hipot set is never left unattended while energized — if both technicians must leave, the voltage is ramped down and the set is shut off.
Common NETA Hipot Safety Traps
Applying full voltage instantly — ramp gradually.
Discharging with an uninsulated tool — always use a resistor discharge stick.
Skipping the post-test 4× ground — the cable can re-energize from dielectric absorption.
Leaving the test set grounded to the source neutral — use an isolation transformer for floating tests.
Trip-testing a relay to an in-service breaker without isolating the trip circuit — notify the operator and rack out or isolate.