Study guide
1.1 About the NETA Level 2 Exam
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
1.1 About the NETA Level 2 Exam
Key Takeaways Explain This Topic AI
Per NETA's Technician Certification page, the NETA ETT Level 2 (Certified Assistant Technician) exam is a 100-item, multiple-choice, closed-book, onsite proctored examination with two hours allowed to complete it.
The exam is organized into four ANSI/NETA ETT Detailed Content Outline domains: Safety (15%), Electrical Testing Fundamentals and Theory (25%), Component Testing (55%), and Systems and Commissioning (5%).
Scaled scores range from 200 to 500, and 410 is the passing scaled score established through NETA's formal standard-setting process.
The exam fee is set by NETA and administered through the candidate's NETA Accredited Company; NETA does not post the current fee publicly.
An on-screen calculator and the NETA Formulae Sheet are provided during the exam; you do not bring your own references.
Last updated: August 2026
About the NETA ETT Level 2 Certified Assistant Technician Exam
Quick Answer: The NETA Level 2 exam is a closed-book, computer-based exam delivered by Pearson VUE. NETA publishes the specification directly: 100 multiple-choice items, closed-book, onsite proctored, with two hours allowed. It is scored on a 200–500 scale and you need a 410 to pass. The content is split across four ANSI/NETA ETT Detailed Content Outline domains — Safety (15%), Electrical Testing Fundamentals and Theory (25%), Component Testing (55%), and Systems and Commissioning (5%) — and the exam fee is managed through your NETA Accredited Company, not posted publicly.
The NETA ETT Level 2 Certified Assistant Technician exam is administered by the InterNational Electrical Testing Association (NETA) under the ANSI/NETA ETT standard. It is the first fully certified tier in the NETA Electrical Testing Technician hierarchy: Level 1 is a Trainee assessed by the employer, while Level 2 is the first credential that requires a proctored Pearson VUE exam and roughly two years of qualifying field experience.
Level 2 technicians perform limited testing and service work under the direct supervision of a Level 3 Certified Technician or Level 4 Senior Certified Technician . They are expected to understand lockout/tagout, arc-flash and shock hazards, and how to assure their own safety on a test floor — but they do not independently sign off on acceptance test reports or run large projects.
Exam Format at a Glance
- Detail Information
- Exam Name NETA ETT Level 2 Certified Assistant Technician
- Administrator NETA, delivered by Pearson VUE
- Question Count 100 multiple-choice items (NETA published exam specification)
- Time Limit 2 hours
- Format Closed-book, computer-based, onsite proctored
- Provided During Exam On-screen calculator, NETA Formulae Sheet
- Scoring Scale 200–500 (scaled)
- Passing Score 410 scaled
- Exam Fee Set by NETA; billed through your NETA Accredited Company (not publicly posted)
- Delivery Pearson VUE authorized test centers
NETA publishes the Level 2 exam specification on its Technician Certification page: a 100-item, multiple-choice, closed-book, onsite proctored examination with two hours allowed and a passing scaled score of 410 on a 200–500 scale . Because there are 100 items and 120 minutes, your working budget is about 1 minute 12 seconds per question — comfortable for recall items, tight if you stall on calculations, so flag and move on rather than burning four minutes on one transformer problem. The same page publishes the domain weights — 15% Safety, 25% Fundamentals and Theory, 55% Component Testing, 5% Systems and Commissioning — so more than half of your study effort should be aimed at component test procedures, acceptance criteria, and the standards that govern them.
The Four DCO Domains
Every NETA exam (Levels 2, 3, and 4) is built from the same four ANSI/NETA ETT Detailed Content Outline domains, but the weighting and depth shift by level. At Level 2 the domains are:
Safety (15%) — NFPA 70E approach boundaries and PPE, OSHA 1910.147 lockout/tagout and 1910.269, energized work permits, temporary protective grounds, induced-voltage mitigation, and hipot testing safety.
Electrical Testing Fundamentals and Theory (25%) — Three-phase systems, grounded vs. grounding conductors, ANSI device numbers (27, 50, 51, 59, 86, 87), CT/PT theory, IDMT curves, voltage unbalance, and symmetrical components basics.
Component Testing (55%) — Insulation resistance (IR), polarization index (PI), dielectric absorption ratio (DAR), transformer turns ratio (TTR), winding resistance, contact resistance (Ductor), ground electrode testing (fall-of-potential and clamp-on), VLF and DC hipot, vacuum bottle integrity, and surge protective device verification.
Systems and Commissioning (5%) — Automatic transfer switch testing, control-circuit IR, as-found/as-left documentation, NFPA 110 emergency system tests, and restoration/handover workflow.
A common Level 2 trap is treating Safety as a small domain and skimming it. Safety items are conceptually quick, but the boundary distances, PPE category cal/cm² values, and glove class tables are heavily memorization-driven and easy points if you drill them. Component Testing dominates the exam, so do not under-prepare there.
The 5% weight on Systems and Commissioning surprises some candidates who have spent significant field time on automatic transfer switches and NFPA 110 generators. Keep in mind that a 5% domain on a roughly 100-item exam is only about five items, so this is a domain to cover competently but not to over-invest in relative to Component Testing. The exam rewards breadth across all four domains plus depth in Component Testing — not over-specialization in any one area.
It is also worth understanding what the exam is not . The NETA Level 2 exam is not a journeyman electrician exam, not a PE-style engineering exam, and not a design exam. It assumes you can already execute tests on real equipment under supervision, and it checks that you know the procedures, acceptance criteria, and safety boundaries well enough to do so without being coached step-by-step. Field time is the prerequisite; the exam certifies that the field time stuck.
Closed-Book, but Not Reference-Free
The exam is closed-book — you cannot bring NFPA 70E, the NEC, or your own notes into the test center. However, NETA provides an on-screen calculator and the NETA Formulae Sheet during the exam. That means you should not waste memorization bandwidth on formula constants you will be handed; instead, drill the application of those formulas (when to use PI vs. DAR, what TTR acceptance tolerance applies, how to interpret a micro-ohm contact resistance reading against a baseline).
Exam Fee and Registration
NETA does not publish the current Level 2 exam fee on its public website. The fee is set by NETA and managed through your NETA Accredited Company (NAC). If you are not currently employed by a NAC (or a NETA Approved Military Organization), you are not eligible to sit for the exam — see Section 1.2 for the full eligibility chain.
Official Resources
NETA Technician Certification — Level definitions, experience requirements, and the current Level 2 exam specification.
NETA Exam Preparation — Detailed Content Outlines, the Formulae Sheet, and the reference list.
Pearson VUE NETA Scheduling — Test center scheduling and test-day policies.
NETA Exam Reminders — The Authorization to Test flow and the 60-day retake waiting period.