Study guide
1.4 Study Plan & How to Use This Guide
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
1.4 Study Plan & How to Use This Guide
Key Takeaways Explain This Topic AI
Plan 120–200 hours of focused study if you have roughly 2 years of field experience; new-to-the-trade candidates should plan closer to the top of that range or beyond.
The four-phase study path is: Master the DCO Domains (20h), Component Testing Deep Dive (50h), Safety and Standards (30h), and Systems/Commissioning and Exam Mechanics (20h).
Core references are NFPA 70E, NFPA 70 (NEC), IEEE 43, ANSI/NETA ATS, ANSI/NETA MTS, ANSI/NETA ETT, and manufacturer documentation; the NETA Formulae Sheet is provided on exam day so drill application, not constants.
Use the in-guide quizzes as recall checks, not as your only source of practice — pair them with the $100 official NETA Practice Exam once you are consistently passing free sets.
Weight your hours toward Component Testing (55% of the exam) and Safety standards (the highest-density memorization domain).
Last updated: August 2026
How Much Time You Need
For a candidate with the typical ~2 years of qualifying field experience, plan 120–200 hours of focused study. If your field experience is light or you are transitioning from a different electrical trade, plan toward the top of that range or beyond. The exam is closed-book, and the Component Testing domain alone carries 55% of the items — there is no shortcut for drilling IR/PI/DAR, TTR tolerances, micro-ohm contact resistance baselines, and ground electrode methods until they are automatic.
The Four-Phase Study Path
This guide is organized to match the way the NETA Level 2 exam is built. Work the four phases in order:
Phase Focus Hours Why
1 Master the NETA DCO Domains 20 Build the skeleton — map every topic back to Safety, Fundamentals/Theory, Component Testing, or Systems/Commissioning so you always know which domain a question is testing.
2 Component Testing Deep Dive 50 The largest domain (55%). Drill IR, PI (10-min/1-min), DAR (60-s/30-s), TTR (±0.5%), winding resistance, Ductor, ground testing (fall-of-potential, clamp-on), VLF and DC hipot, vacuum bottle integrity, and SPD verification.
3 Safety and Standards 30 NFPA 70E approach boundaries and PPE categories (1/2/3/4 at 4/8/25/40 cal/cm²), rubber glove classes (00–4), OSHA 1910.147 lockout/tagout and 1910.269, IEEE 43, and the ANSI/NETA ATS vs. MTS distinction.
4 Systems, Commissioning, and Exam Mechanics 20 ATS testing, NFPA 110 emergency systems, as-found/as-left documentation, restoration workflow, and Pearson VUE test-day procedures so nothing about the exam itself surprises you.
The hours above sum to 120. Use the remaining 0–80 hours (up to the 200-hour ceiling) for spaced repetition of weak domains, additional practice question sets, and — near the end — the official NETA Practice Exam.
Core References
Per NETA's Exam Preparation page, the references you are expected to know include:
NFPA 70E — Standard for Electrical Safety in the Workplace. Approach boundaries, PPE categories, energized work permits.
NFPA 70 (NEC) — National Electrical Code. Grounding, conductor sizing, device ratings.
IEEE 43 — Recommended Practice for Testing Insulation Resistance of Electric Machinery. IR, PI, DAR, the kV+1 vs. 100 megohm minimum.
ANSI/NETA ATS — Acceptance Testing Specifications. New equipment commissioning.
ANSI/NETA MTS — Maintenance Testing Specifications. In-service equipment maintenance.
ANSI/NETA ETT — The standard that defines the certification program itself, including the Detailed Content Outlines.
Manufacturer documentation — Instruction books for the specific switchgear, transformers, and relays you test.
You do not need to memorize formula constants. The NETA Formulae Sheet is provided on-screen during the exam. What you must drill is when to apply each formula and how to interpret the result against the correct acceptance criterion.
How to Use the Quizzes in This Guide
The quizzes embedded in this guide are recall and application checks , not a full simulation of the 100-item exam. Use them as follows:
Read the section first. Do not quiz before you have read the teaching prose — you will only test what you already knew.
Answer before you look. Commit to an option before reading the explanation. The explanation is there to confirm or correct, not to scaffold.
Re-quiz on weak domains. If you miss a question, mark the topic and return to it in a later session. Spaced repetition beats cramming for closed-book exams.
Pair with the official practice exam. Once you are consistently passing free quiz sets, buy the $100 NETA Official Practice Exam (40–50 retired questions, one hour, 60-day results review) as a dress rehearsal. Do not burn it on day one.
A Week-by-Week Skeleton
If you have ~12 weeks and can commit ~10 hours per week (120 hours total), a workable skeleton is:
Weeks 1–2 — Phase 1: DCO domain mapping + Fundamentals/Theory drill (ANSI device numbers, CT/PT, three-phase).
Weeks 3–8 — Phase 2: Component Testing deep dive, two domains per week (IR/PI/DAR; TTR and winding resistance; Ductor and ground testing; hipot and vacuum bottles; SPD; mixed review).
Weeks 9–10 — Phase 3: Safety and standards (NFPA 70E, OSHA, IEEE 43, ATS vs. MTS).
Week 11 — Phase 4: Systems/Commissioning and exam mechanics; schedule the Pearson VUE date.
Week 12 — Official Practice Exam, weak-area patching, and rest.
Adjust the skeleton to your actual field experience. If you have been running IR and TTR weekly for two years, compress Phase 2 and expand Phase 3. If your field experience is light, do the opposite.
One more study-planning principle: spaced repetition beats cramming for a closed-book exam. Three 3-hour sessions across a week retain more than one 9-hour marathon, especially for memorization-heavy material like NFPA 70E boundary distances and ANSI device numbers. Build your schedule around short, frequent sessions and reserve the final week for the official practice exam and weak-area patching, not for learning new material.
A note on the official practice exam timing: activate it only when you are within ~60 days of your scheduled Pearson VUE appointment, because the 60-day review window starts at activation. Activating it too early means you lose access before test day; activating it too late means you cannot act on what it tells you. Treat the practice exam result as a go/no-go signal — if you are not comfortably above 410-equivalent on it, push your Pearson VUE appointment out rather than sitting the real exam under-prepared — a voluntary delay costs you nothing, while a failure locks you out for a mandatory 60 days.
Official Resources
NETA Exam Preparation — Detailed Content Outlines, the Formulae Sheet, and the reference list.
NETA Detailed Content Outlines (PDF) — The official DCO for every level.
NETA Study Guide (PDF) — NETA's own study guide.
NETA Official Practice Exam — The $100 retired-item practice exam for your dress rehearsal.
Pearson VUE NETA Scheduling — Test center scheduling.