Study guide

3.5 Insulation Degradation & Dielectric Theory

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

3.5 Insulation Degradation & Dielectric Theory

Key Takeaways Explain This Topic AI

Insulation degrades via four modes — thermal (overload/aging), electrical (partial discharge, corona), mechanical (vibration, thermal cycling), and environmental (moisture, contamination, water treeing).

When DC test voltage is applied, total current is the sum of capacitive charging current (decays in seconds), polarization/absorption current (decays over minutes), and conduction leakage (steady-state); IR at 1 minute and 10 minutes measure these.

Polarization Index (PI = IR10min / IR1min) and Dielectric Absorption Ratio (DAR = IR60s / IR30s) detect absorption behavior — a low PI indicates moist or contaminated insulation.

Per IEEE 43-2013, minimum IR for older windings and all field windings is kV + 1 MΩ at 40°C; modern post-1970 form-wound stators use 100 MΩ; random-wound and sub-1 kV coils use 5 MΩ.

Insulation resistance varies inversely with temperature; readings must be corrected to 40°C before trending. PI does not need temperature correction because both readings are at the same temperature.

Last updated: August 2026

The Four Insulation Degradation Modes

Quick Answer: Insulation fails by thermal, electrical, mechanical, and environmental mechanisms. Most real failures combine two or more — a thermally aged winding absorbs moisture, tracks, and then breaks down electrically.

Thermal: Every 10°C above the insulation class rating roughly halves insulation life (the Dakin-Arrhenius relationship). Overload, blocked ventilation, and cyclic loading embrittle the resin and delaminate layers. Most common long-term degradation.

Electrical: Partial discharge (PD) in voids erodes resin via ion bombardment and ozone. Corona is high-voltage PD in air. Treeing (electrical trees in solid insulation, water trees in XLPE cables) is slow dendritic breakdown driven by voltage stress and moisture. Tracking is carbonized surface conduction paths from contamination and leakage.

Mechanical: Vibration loosens windings in slots, thermal cycling expands and contracts conductors, and short-circuit magnetic forces deform coils. Abrasion creates voids that invite PD.

Environmental: Moisture lowers IR and promotes water treeing; dust, oil, and chemical contamination create surface leakage paths. Motors stored without space heaters absorb moisture and fail on first energization.

IR, PI, DAR, surge, PD, tan-delta, and VLF cable tests each detect different combinations of these modes — which is why NETA acceptance packages use several methods.

Dielectric Theory: Three Currents in an IR Test

When you apply DC test voltage (e.g., 1,000 or 5,000 V with a megohmmeter), the total current is the sum of three components with different time constants:

Capacitive charging current (Ic): high initially, decays in seconds as the geometric capacitance charges — usually gone within the first minute.

Polarization / absorption current (Ia): decays over minutes to tens of minutes as dipolar molecules align with the field and interfacial (Maxwell-Wagner) polarization develops. This is the current PI and DAR measure.

Conduction leakage current (Ig): steady-state current through and over the insulation — what the final IR reflects.

The megohmmeter reads IR = Vapplied / (Ic + Ia + Ig). As Ic and Ia decay, measured current drops and IR rises. On good, dry insulation IR keeps climbing for 10 minutes; on wet or contaminated insulation, conduction leakage dominates and IR flattens within a minute.

Why IR, PI, and DAR Work

Insulation Resistance (IR): the 1-minute value, IR₁ — IEEE 43 references this for minimum acceptance.

Dielectric Absorption Ratio (DAR): DAR = IR(60 s) / IR(30 s). Good dry insulation shows DAR ≥ 1.4; below 1.25 suggests moist or contaminated insulation. Used where a 10-minute test is impractical.

Polarization Index (PI): PI = IR(10 min) / IR(1 min). Good insulation shows PI ≥ 2.0 (class A) or ≥ 2.5-4.0 for modern epoxy; PI < 1.0 is unacceptable. PI is temperature-independent (both readings at the same temperature) and the most sensitive of the three to absorption behavior.

A low PI does not always mean low IR — a winding can have a high 1-minute IR but flatten out, indicating absorption is absent (moisture-saturated or contaminated). PI is the trending tool; IR is the acceptance tool.

IEEE 43-2013 Minimum IR (at 40°C)

IEEE 43-2013 Clause 12.3 gives three minimum IR₁ values:

  • Minimum IR₁ at 40°C Application
  • kV + 1 MΩ Most windings made before ~1970, all field windings, and others not described below
  • 100 MΩ Most AC windings built after ~1970 (form-wound stators)
  • 5 MΩ Random-wound stator coils, form-wound coils rated below 1 kV, and DC armatures

The 'kV' is the rated line-to-line RMS voltage in kilovolts for three-phase AC machines, line-to-ground for single-phase, and rated DC voltage for DC machines or field windings. A 13.8 kV machine has a kV + 1 minimum of 14.8 MΩ. For modern post-1970 form-wound stators the 100 MΩ floor is usually the controlling minimum (because 100 > kV + 1 for typical machines).

Temperature Correction

Insulation resistance varies inversely on an exponential basis with temperature — higher temperature means lower IR. IEEE 43-2013 corrects readings to 40°C using Rc = KT × RT. The simple field approximation for thermoplastic insulation is the '2× per 10°C' rule: IR halves for every 10°C rise, doubles for every 10°C drop. Modern thermosetting (epoxy/polyester) insulation is less sensitive and uses a different formula.

  • Winding T (°C) KT (thermoplastic) KT (thermosetting)
  • 20 0.25 0.8
  • 30 0.5 0.9
  • 40 1.0 1.0
  • 50 2.0 1.5
  • 60 4.0 2.3

Always record winding temperature at every test — without it, the reading is useless for trending. PI and DAR do not need temperature correction (both readings are at the same temperature, so KT cancels). Do not apply the thermoplastic correction to modern epoxy windings — it over-corrects. Moisture invalidates the correction below the dew point; dry the winding (space heaters, blanked-off motor with low-current heat) before taking acceptance readings.

Insulation Coordination: BIL and Clearances

Insulation coordination (IEEE C62.82) matches equipment insulation strength to the protective level of surge arresters so switching and lightning surges are clipped below the equipment's withstand. Key terms:

BIL (Basic Insulation Level): the standard lightning-impulse withstand voltage, in kV crest of a 1.2/50 μs wave. A 15 kV class switchgear has a typical BIL of 95 or 110 kV.

CFO (Critical Flashover): the impulse voltage at which 50% of impulses cause flashover.

Surge arrester protective level: the residual voltage across the arrester when it conducts the expected surge current. The margin between BIL and arrester protective level is the coordination margin (typically ≥20%).

Clearances: minimum air distances between live parts and ground, set by BIL and voltage class. NETA acceptance tests verify clearances during visual inspection.

Poor coordination lets surges reach the insulation, causing puncture or flashover — exactly what IR, PI, hipot, and VLF tests try to detect after the fact.

Exam Trap

Do not apply a generic '100 MΩ minimum' to every machine. IEEE 43-2013 sets three different minimums depending on insulation age and winding type. A pre-1970 winding or any field winding uses kV + 1 MΩ. A modern form-wound stator uses 100 MΩ. A random-wound stator or sub-1 kV coil uses 5 MΩ. A 13.8 kV machine under the kV + 1 rule only needs 14.8 MΩ — well below 100. If the exam names the machine age or winding type, pick the right row of the table.