Study guide

3.3 Symmetrical Components & Fault-Current Paths

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

3.3 Symmetrical Components & Fault-Current Paths

Key Takeaways Explain This Topic AI

Fortescue's theorem decomposes any unbalanced three-phase phasor set into positive, negative, and zero sequence components; balanced systems contain only positive sequence.

A single-line-to-ground (L-G) fault involves all three sequence networks in series: I = 3V / (Z1 + Z2 + Z0); a three-phase fault involves only Z1; a line-to-line fault involves Z1 and Z2.

With equal sequence impedances (Z1 = Z2 = Z0), L-G fault current equals the three-phase fault current; with high Z0 (impedance-grounded systems), L-G current is much lower.

A line-to-line fault is about 87% (√3/2) of the three-phase fault magnitude when Z1 = Z2.

Fault type and magnitude drive relay coordination, CT ratio selection, and breaker interrupting ratings — knowing which sequence networks are involved tells you why L-G faults on impedance-grounded systems are low enough to alarm rather than trip.

Last updated: August 2026

The Three Sequence Networks

Quick Answer: Any set of three unbalanced phasors can be decomposed into three balanced sets: positive sequence (normal rotation, ABC), negative sequence (reverse rotation, ACB), and zero sequence (three in-phase phasors that add in the neutral/ground path).

C.L. Fortescue's 1918 theorem is the foundation of modern fault analysis. Each sequence has its own network impedance:

Z1 (positive sequence): the impedance seen by a balanced positive-sequence set — the normal load impedance, including source, transformer, and line.

Z2 (negative sequence): the impedance seen by a negative-sequence set. For static equipment (transformers, lines) Z2 ≈ Z1. For rotating machines Z2 is different and usually smaller.

Z0 (zero sequence): the impedance seen by three in-phase currents that return through neutral or ground. Z0 depends strongly on transformer winding connection and grounding — a delta winding blocks zero sequence, a wye with grounded neutral passes it.

A balanced three-phase system contains only positive sequence . Unbalanced conditions (L-G fault, open phase, unbalanced load) introduce negative and/or zero sequence.

Which Networks Each Fault Type Uses

  • Fault Type Sequence Networks Fault Current (per phase, V = pre-fault L-N)
  • Three-phase (3φ) Z1 only I = V / Z1
  • Line-to-line (L-L) Z1 + Z2 in series I = V / (Z1 + Z2)
  • Single line-to-ground (L-G) Z1 + Z2 + Z0 in series I = 3V / (Z1 + Z2 + Z0)
  • Double line-to-ground (L-L-G) Parallel combination More complex; involves all three
  • Fault Magnitude Relationships

Assume the common simplification Z1 = Z2 = Z (true for static equipment) and compare to the three-phase fault current I3φ = V / Z1:

Three-phase: I3φ = V / Z (the reference).

L-L fault: ILL = V / (Z1 + Z2) = V / (2Z). Compared to I3φ: ILL / I3φ = Z / (2Z) × (note L-L uses L-L voltage). The standard result is ILL ≈ 0.866 × I3φ (√3/2 of the three-phase fault) when Z1 = Z2.

L-G fault (Z0 = Z1): ILG = 3V / (3Z) = V / Z = I3φ. L-G equals the three-phase fault when Z0 = Z1.

L-G fault (Z0 = 3 × Z1, typical impedance-grounded): ILG = 3V / (Z + Z + 3Z) = 3V / (5Z) = 0.6 × V/Z = 0.6 × I3φ . Lower than 3φ.

L-G fault on an ungrounded system: Z0 is essentially infinite (only capacitive charging current returns), so ILG ≈ 0 — only a few amps of charging current. This is why ungrounded systems keep operating on a single ground fault but alarm instead of tripping.

The key insight: L-G fault magnitude depends almost entirely on Z0 , which depends on transformer connection and grounding choice. Three-phase and L-L faults do not involve Z0.

The Fault-Current Path in a Wye System

On a solidly grounded wye system (e.g., 480Y/277 V with neutral-ground bond at the service), a line-to-ground fault drives current from the source transformer secondary, through the phase conductor, through the fault to ground/neutral, back through the equipment grounding conductor (EGC) to the service neutral-ground bond, and through the neutral to the source. The path is metallic and low-impedance , so L-G fault current is high — high enough to operate a standard overcurrent relay (51) or instantaneous element (50).

On an impedance-grounded system (covered in 3.4) the neutral-ground bond includes a resistor or reactor, so the same path carries only a limited current (typically 5-400 A). The system alarms but does not trip on the first ground fault — useful where continuity of service matters.

Why This Matters for NETA Work

Relay coordination: A 51/51N relay must be set to trip for L-G faults in its zone but to wait (coordinate) for a downstream device to clear first. Knowing whether the system is low-Z or high-Z grounded tells you whether to expect a high-magnitude L-G fault or a low-magnitude alarm condition.

CT selection: CT ratios and accuracy classes (e.g., C100, C200, C400, C800) are chosen so the CT does not saturate during the maximum fault current. If you underestimate L-G fault current because you forgot the system is solidly grounded, the CT saturates and the relay misoperates.

Differential (87) relays: Through-fault stability depends on CT matching and on the actual fault current. An L-G through-fault on a grounded-wye transformer produces zero-sequence current that can fool a differential scheme unless the CTs are wye-connected with the zero sequence accounted for.

Breaker interrupting duty: The breaker must interrupt the maximum fault at its location. Three-phase faults often set the duty on solidly grounded systems, but L-G faults can exceed 3φ on systems with very low Z0 (e.g., solidly grounded generator neutrals).

Exam Trap

A common Level 2 trap is to assume L-G fault current is always lower than 3φ fault current. It is not always lower. On a solidly grounded system with Z0 < Z1 (e.g., a generator with a solidly grounded neutral), L-G fault current can exceed the 3φ fault current by up to ~1.5×. The relationship depends entirely on Z0. When a question gives a grounding configuration, use it — do not default to "L-G is smaller."