Study guide
3.1 Three-Phase Power & Wye/Delta Relationships
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
3.1 Three-Phase Power & Wye/Delta Relationships
Key Takeaways Explain This Topic AI
Three-phase real power: P = √3 × VLL × IL × PF; apparent power S = √3 × VLL × IL, and reactive power Q = √3 × VLL × IL × sin θ.
In a wye system VLL = √3 × VLN (so 480Y/277 V means 480 V line-to-line and 277 V line-to-neutral); in a delta system line voltage equals phase voltage.
Positive (ABC) sequence means A leads B by 120° and B leads C by 120°; reversing rotation (ACB) runs motors backward and can misoperate directional relays.
In a balanced wye system the vector sum of the three line currents is zero, so the neutral carries only imbalance/harmonic current.
For the same line voltage and line current, a balanced three-phase system delivers √3 times the real power of a single-phase circuit at that same voltage and current.
Last updated: August 2026
The Three-Phase Power Formula
Quick Answer: For a balanced three-phase load, total real power P = √3 × VLL × IL × PF , apparent power S = √3 × VLL × IL , and reactive power Q = √3 × VLL × IL × sin θ . Use line-to-line voltage and line current — never mix in a phase voltage by mistake.
The single-phase formula P = V × I × PF extends to three phases by multiplying by 3 if you use per-phase quantities: P = 3 × Vphase × Iphase × PF. In a wye connection Iphase = IL and Vphase = VLN, so P = 3 × VLN × IL × PF. Because VLN = VLL / √3, this simplifies to P = √3 × VLL × IL × PF . In a delta connection Vphase = VLL and Iphase = IL / √3, which produces the same √3 result. The formula is identical for both connections when you use line quantities.
θ is the angle between the phase voltage and phase current. Power factor PF = cos θ. A 0.85 PF means θ ≈ 31.8° and sin θ ≈ 0.527.
Where the √3 Comes From
The √3 factor is not a fudge number — it falls directly out of the 120° phase displacement. In a wye system the line-to-line voltage is the vector difference of two phase voltages that are each VLN in magnitude and 120° apart. Using the law of cosines, the magnitude of that difference is VLL = √(V LN² + V LN² − 2·V LN²·cos 120°) = √(2·V LN²·(1 − (−0.5))) = √(3·V LN²) = √3 · V LN . The same geometry, applied to currents in a delta, gives IL = √3 · Iphase. Remembering the geometry makes the wye/delta tables below intuitive instead of memorized: voltage converts by √3 in wye, current converts by √3 in delta, and the conversion always goes the same way because the underlying 120° relationship is identical.
Wye vs. Delta Voltage and Current Relationships
- Quantity Wye (Y) Delta (Δ)
- Line-to-line voltage VLL = √3 × Vphase VLL = Vphase
- Line current IL = Iphase IL = √3 × Iphase
- Phase voltage Vphase = VLN = VLL / √3 Vphase = VLL
- Neutral available Yes (4-wire systems) No neutral
- Common service 480Y/277 V, 208Y/120 V 240 V, 480 V (3-wire)
A 480Y/277 V service is a wye system: 480 V between any two lines, 277 V from any line to neutral, and the neutral is brought out as a fourth conductor. A 480 V delta service has 480 V between lines and no neutral.
Phase Rotation: ABC vs ACB
Positive sequence (ABC) means phase A reaches its positive peak first, then B lags A by 120°, then C lags B by 120°. Negative sequence (ACB) reverses the order — C leads B leads A. Phase rotation matters for two big reasons on the NETA exam:
Motor rotation: A three-phase induction motor's shaft direction follows the phase rotation. Swapping any two leads reverses rotation. Before commissioning a motor, verify rotation with a phase-rotation tester — reversing a 1,500 hp pump motor can shear a coupling or wreck a pump.
Directional relays: ANSI 67 directional overcurrent and 87 transformer differential relays use phase rotation to establish torque direction. Wrong rotation makes the relay trip for through-faults or fail to trip for internal faults. Always confirm rotation during commissioning with a phase-sequence indicator before energizing protection.
Balanced vs. Unbalanced Systems
A balanced three-phase system has equal magnitudes on all three phases and 120° displacement between them. In a balanced wye system the vector sum of the three line currents is zero, so a neutral conductor (if present) carries zero current at fundamental frequency. In an unbalanced system the magnitudes or angles differ, the neutral carries the imbalance, and negative-sequence currents appear (covered in 3.2).
Worked Example
A 480 V three-phase motor draws 100 A per phase at 0.85 power factor. Find real, apparent, and reactive power.
Apparent power: S = √3 × VLL × IL = 1.732 × 480 × 100 = 82,944 VA ≈ 82.9 kVA .
Real power: P = S × PF = 82.9 × 0.85 = 70,466 W ≈ 70.5 kW . (Direct: √3 × 480 × 100 × 0.85 = 70,656 W — the small difference is rounding of √3.)
Reactive power: Q = S × sin θ = 82.9 × sin(31.8°) = 82.9 × 0.527 = 43.7 kVAR ≈ 43.7 kVAR .
Line-to-neutral voltage: VLN = 480 / √3 = 277 V .
If PF were unity (1.0), P would equal S at 82.9 kW and Q would be zero. As PF drops, more current flows for the same real power — which is why utilities and NETA test reports track PF.
Delta Current Example
A 480 V delta-connected load draws 50 A through each phase winding. What is the line current and the total apparent power?
Line current: IL = √3 × Iphase = 1.732 × 50 = 86.6 A . In a delta the line current splits between two windings, so the line current is larger than the winding current by √3.
Apparent power: S = √3 × VLL × IL = 1.732 × 480 × 86.6 = 72,000 VA ≈ 72 kVA . Cross-check per phase: each winding sees Vphase = VLL = 480 V at Iphase = 50 A, so 3 × 480 × 50 = 72,000 VA. The two methods agree, which confirms you used the correct √3 relationship for each quantity.
Delta-Wye Transformer Phase Shift
Most NETA acceptance tests involve at least one delta-wye transformer, and these introduce a 30° phase shift between the primary (delta) and secondary (wye) voltages. The high-voltage delta winding's line-to-line voltage leads the low-voltage wye's line-to-neutral voltage by 30° for a standard Dy1 connection. This shift matters because transformer differential relays (ANSI 87T) compare currents on both sides; the relay's compensation windings or numerical phase-shifting must cancel the 30° shift, or the relay sees a false differential current and trips on through-load. When commissioning a delta-wye bank, verify the vector group nameplate (e.g., Dy1, Dy11) and confirm the relay's phase compensation matches it — a common NETA Level 2 commissioning task.
Exam Trap
Do not use VLN in the √3 formula. The √3 factor already converts line-to-line voltage to the per-phase quantity. Mixing VLN into P = √3 × VLL × IL × PF double-counts the √3 and gives an answer 1.732× too high. If a question gives 277 V and 100 A in a wye system, either convert to 480 V line-to-line and use the √3 formula, or use P = 3 × 277 × 100 × PF directly.