Study guide
4.4 PT/VT Fundamentals & Insulation Coordination
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
4.4 PT/VT Fundamentals & Insulation Coordination
Key Takeaways Explain This Topic AI
A potential transformer (PT, also called voltage transformer or VT) steps primary voltage down to a standardized secondary (commonly 120 V in IEEE practice, 110 V in IEC) for relays and meters; its ratio (e.g. 14400:120) sets the voltage scale of every connected device.
PT secondaries are fused and grounded: fuses clear PT-side faults (which would otherwise feed from the secondary bus), and grounding one secondary conductor limits the secondary-to-ground voltage and provides a reference for relays.
Insulation coordination per IEEE C62.82 matches equipment BIL to surge arrester protective levels so arresters clip surges below the equipment withstand — for a 15 kV class system, typical BIL is 95 or 110 kV.
IEC 60947 distinguishes Ui (rated insulation voltage, which sets clearances and creepage) from Ue (rated operational voltage, which sets the utilization rating); Ui may exceed Ue.
CTs are series-connected (current instruments) and must never have their secondary opened; PTs are shunt-connected (voltage instruments) and must never have their secondary shorted.
Last updated: August 2026
PT/VT Ratio and Fusing
Quick Answer: A potential transformer (PT) — also called a voltage transformer (VT) — is a shunt-connected instrument transformer that steps line voltage down to a standardized secondary. A 14400:120 PT produces 120 V secondary at 14400 V primary, a 120:1 ratio.
Common secondary ratings are 120 V in IEEE/North American practice and 110 V in IEC practice. Relay settings sheets express primary quantities in secondary volts scaled by the PT ratio: a 59 overvoltage relay set to 110 V secondary on a 14400:120 PT operates at 13,200 V primary (110 x 120).
PTs are protected on both sides:
Primary fuses or cutouts clear internal PT faults and isolate the PT from the high-voltage bus. Current-limiting or power fuses are typical above 15 kV; expulsion cutouts are common on distribution PTs.
Secondary fuses (or miniature circuit breakers) clear faults on the secondary wiring, relay/meter short circuits, and backfeed from paralleled PT secondaries. A short on the secondary of an unfused PT would draw very high current (the PT has a low per-unit impedance) and could damage the PT and downstream wiring.
PT Secondary Grounding Practices
One secondary conductor (typically X2 on a single-phase PT, or the star point on a three-phase PT bank) is grounded at one point only . The reasons:
Safety and voltage reference. Grounding fixes the secondary-to-ground voltage at a known value (no more than 120 V to ground for a 120 V secondary), protecting personnel and relay insulation from floating voltages.
Relay reference. Many relays (27, 59, 25 synchronizing) reference phase-to-ground voltage; without a grounded secondary the reference is undefined.
Fault detection. A single ground reference lets a secondary ground fault show up as a clear voltage disturbance rather than a silent voltage shift.
Grounding is done at one point only to prevent circulating currents through the secondary neutral. Multiple grounds create a parallel path through the station ground grid that can drive current through the neutral and bias voltage relays. The single-point ground is usually at the PT junction box or the first relay panel, and it is the first thing to verify on an acceptance test.
Why PT Secondaries Are Fused and Grounded (Summary)
- Feature Purpose
- Primary fuse Clear internal PT faults; isolate from HV bus
- Secondary fuse Clear secondary wiring faults, relay/meter shorts, paralleled-PT backfeed
Single-point secondary ground Fix secondary-to-ground voltage; provide relay reference; avoid circulating neutral currents
Insulation Coordination: BIL and Surge Protection Margin
Insulation coordination (IEEE C62.82) is the practice of matching every piece of equipment's insulation withstand to the protective level of surge arresters so that surges are clipped below what the equipment can survive. The key quantities:
BIL (Basic Insulation Level). The crest value of a standard 1.2 x 50 microsecond lightning impulse the equipment must withstand. For a 15 kV class system, typical BIL is 95 kV (older) or 110 kV (modern). For 5 kV class, BIL is about 60 kV.
Chopped-wave withstand. A higher-crest, shorter-duration impulse the equipment must also survive; typically 1.15 to 1.25 x BIL.
Switching surge withstand. A longer-front impulse; relevant above about 230 kV.
Surge arrester protective level. The maximum voltage the arrester allows through during a surge (front-of-wave, lightning, and switching discharge voltages).
Protective margin. The ratio or percent difference between equipment BIL and arrester protective level. A common target is at least 20% margin: PM = (BIL - protective level) / protective level.
A NETA Level 2 tech sees this in two acceptance tasks: verifying surge arrester nameplate data against the BIL of the protected equipment, and (per ANSI/NETA ATS) performing visual, mechanical, and electrical inspection of surge arresters. MOV blocks are not field-disassembled; the field check is inspection plus, where specified, a reference test against manufacturer data.
IEC Ratings: Ui and Ue
IEC 60947 low-voltage equipment uses two voltage ratings that are easy to confuse:
Ui (rated insulation voltage). The reference value for insulation withstand capability; it sets the creepage and clearance requirements. Ui may be higher than the operating voltage — a breaker marked Ui 1000 V can be used on a 600 V system.
Ue (rated operational voltage). The voltage at which the breaker is rated to make, carry, and break current; it sets the utilization category and short-circuit rating. Ue is always less than or equal to Ui.
Uimp (rated impulse withstand). The 1.2 x 50 microsecond impulse voltage the breaker insulation must survive; the IEC analogue of BIL for low-voltage gear.
So when you see a European breaker label with Ui 1000 V / Ue 690 V / Uimp 8 kV, read: insulation good to 1000 V, operation rated at 690 V, impulse withstand 8 kV.
CT Versus PT in Relay and Meter Circuits
The CT-versus-PT distinction is a frequent NETA exam point:
- Feature CT PT/VT
- Connection Series (in the line) Shunt (across the line)
- Secondary standard 1 A or 5 A 120 V (IEEE) / 110 V (IEC)
- Quantity measured Current Voltage
- Open-secondary hazard Yes — dangerously high voltage No (but a short draws high current)
- Short-secondary hazard No (normal operation) Yes — blows fuses / damages PT
- Grounding One point of secondary (reference) One point of secondary (reference + safety)
- Polarity matters for 87 differential, 67 directional 25 synchronizing, 27/59, directional elements
The one-line memory aid: CTs are series, never open them; PTs are shunt, never short them. Both have one secondary point grounded, and both require polarity verification before energization.