Study guide

9.1 Contact Resistance (Ductor) & Torque Verification

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

9.1 Contact Resistance (Ductor) & Torque Verification

Key Takeaways Explain This Topic AI

A Ductor (micro-ohmmeter/DLRO) injects a known DC current (typically ~100 A on power breakers) through closed contacts and measures voltage drop to compute resistance in micro-ohms; compare phase-to-phase and to manufacturer baseline.

NETA MTS acceptance is comparative: phase-to-phase contact-resistance readings should not differ by more than about 50% between the highest and lowest pole; values typically run tens to hundreds of micro-ohms.

Rule of thumb on LV power breakers: <= 100 µΩ is good, > 300 µΩ signals trouble (pitting, erosion, loose joints).

Torque values come from the manufacturer's instructions first; where no OEM value is published, the ANSI/NETA ATS/MTS Annex table by bolt size and material governs.

Torque verification uses a calibrated torque wrench (confirm no movement at spec, or mark-and-recheck with a witness mark); impact guns cannot produce a known torque and may damage fasteners.

Last updated: August 2026

Why Contact Resistance Matters

A bolted joint or a breaker main contact that looks fine to the eye can still carry a high-resistance film, pitting, or insufficient contact pressure. Under load that joint heats (I-squared-R), accelerates oxidation, and can cascade into a failure or a fire during a fault. The contact resistance test — universally called the Ductor or DLRO (Digital Low-Resistance Ohmmeter) test — is the standard NETA MTS method for catching those joints before they fail.

How the Ductor Test Works

A micro-ohmmeter injects a known, regulated DC current (typically 100 A on power circuit breakers and bus joints, lower on control contacts) through the closed current path and measures the voltage drop across the joint. Ohm's law gives the resistance directly in micro-ohms (µΩ) . Using DC (not AC) and a four-wire (Kelvin) connection cancels lead and contact resistance, so the reading reflects only the joint under test.

On a three-pole breaker you take a reading on each pole — line-to-load through the closed contacts — and compare phase-to-phase . You also compare to the manufacturer's published value or, on maintenance work, to the baseline from prior tests.

Acceptance Criteria

NETA MTS does not publish a single pass/fail micro-ohm number because resistance scales with the breaker's continuous-current rating (a 100 A frame legitimately reads higher than a 4000 A frame). The acceptance rule is comparative:

  • Reading Interpretation
  • Phase-to-phase spread <= ~50% (high vs. low) Acceptable — balanced contacts
  • All poles within manufacturer spec Acceptable
  • One pole 2–3x the others Investigate — wipe, pitting, or binding
  • LV breaker > ~300 µΩ, or trend rising Trouble — clean, re-torque, or replace contacts

A useful rule of thumb on low-voltage power breakers is that <= 100 µΩ is good and > 300 µΩ indicates trouble . On medium-voltage air-magnetic or vacuum breakers the structures are larger and the same comparative rule applies — look at the spread and the trend, not an absolute number.

Torque Specifications

Loose joints are the #1 preventable cause of switchgear failure, and "loose" almost always means under-torqued . NETA's rule is explicit:

Torque per the manufacturer's published instructions first. If the OEM gives a value for that bolt size, material, and lubricant, use it.

Where no manufacturer data exists , use the torque table in the ANSI/NETA ATS/MTS Annex , indexed by bolt diameter and material (for example, 1/2 in. silicon-bronze vs. 3/8 in. stainless).

Use a calibrated torque wrench — and verify calibration is in date. Torque is a controlled, measured preload, not "good and tight."

Over-torquing is just as bad as under-torquing: it yields the fastener, crushes bus plating, and leaves the joint with less spring force than before.

Torque Verification Method

After a bolted connection is made (or on an existing joint during maintenance), NETA accepts two verification paths:

Re-torque to spec with a calibrated torque wrench and confirm the bolt does not move when the wrench reaches the specified value. Movement means the joint was loose — disassemble, inspect the faces, and reassemble.

Mark-and-recheck : apply a torque-seal / witness mark across the bolt and bus after torquing. On the next maintenance cycle, a broken mark means the joint has loosened (thermal cycling, vibration) and needs re-torque.

A common field trap is reaching for an impact gun. An impact gun cannot produce a known torque — it depends on bolt friction, joint stiffness, and run time — and the hammering can damage plating and threads. NETA considers impact tightening unacceptable for electrical bolted joints.

Why Both Tests Are Required Together

A joint can be torqued correctly and still read high on the Ductor if the contact faces are oxidized, pitted, or contaminated — torque only provides force, not a clean conductive interface. Conversely, a joint can have clean faces and still run hot if the clamping force is low. Running both tests gives you joint integrity: the torque wrench confirms preload, and the Ductor confirms conductive area. Skipping either leaves a gap.

Common Ductor Field Errors

Using a 2-wire ohmmeter — lead and clip resistance (often tens of milliohms) swamps the joint reading. Always use a 4-wire Kelvin DLRO.

Measuring across the wrong span — for a breaker pole the leads go line-to-load through the closed contacts; for a bus joint they go directly across the joint, not the whole bus.

Ignoring polarity/current direction — on a DC test, thermoelectric EMF at dissimilar-metal junctions can offset the reading slightly; many DLROs auto-reverse and average.

Not letting the reading settle — inductive joints (large reactor or transformer leads) need a few seconds for the test current to ramp; record the steady-state value.

Forgetting to record the baseline — without a baseline, a rising trend across years is invisible; always log pole readings and temperature.

Worked Example

A 1600 A LV air circuit breaker is tested after maintenance. Pole A reads 42 µΩ, Pole B reads 38 µΩ, Pole C reads 91 µΩ. The spread (91 vs. 38) is well past the 50% comparative threshold. Before condemning the breaker, re-torque the line/load stabs per the OEM value (say, 45 lb-ft on 1/2 in. hardware). Pole C drops to 44 µΩ — the stab was loose. Re-test confirms the joint is now balanced and the breaker is returned to service.