Study guide

9.6 Metal-Enclosed Busways & Outdoor Bus Structures

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

9.6 Metal-Enclosed Busways & Outdoor Bus Structures

Key Takeaways Explain This Topic AI

Busway insulation resistance is measured phase-to-phase and phase-to-ground on the complete run with plug-in units and connected loads removed, because a single connected load drags the reading down.

A busway megohm reading is not comparable to a cable reading of the same length; busway is short, has large surface area, and is dominated by insulator surface leakage and moisture.

Every bolted busway joint is a resistance and a heat source, so torque verification with a calibrated wrench and thermographic survey under load are the two highest-value busway tests.

Water intrusion is the most common busway failure mode, which is why weatherproof and outdoor busway runs get IR testing before energization after any rain event or roof leak.

Outdoor bus structures are tested as a system of joints and insulators: contact resistance across bolted connections, insulator condition, phase spacing and clearances, and thermography under load.

Last updated: August 2026

Busway: What It Is and Why It Fails

Metal-enclosed busway (bus duct) is prefabricated rigid conductor in a metal housing, used where a cable run would need many parallel conductors: risers in high-rise buildings, switchgear-to-transformer connections, and distribution spines in industrial plants. It is Domain III subdomain D of the Level 2 DCO.

  • Type Construction Application
  • Feeder busway Continuous run, no tap openings Point-to-point transmission of large blocks of power
  • Plug-in busway Tap openings at intervals for plug-in units Industrial distribution where loads move or change
  • Lighting busway Small ampacity, continuous tap slot Lighting and small tool circuits

Low-impedance / sandwich Conductors stacked tightly with insulation between High current with reduced reactance and voltage drop

Isolated-phase bus Each phase in its own enclosure Generator leads at large stations

Busway conductors are copper or aluminum, and the housing may be ventilated (indoor, dry) or totally enclosed / weatherproof . The two dominant failure mechanisms are water intrusion and loose joints , and both are what the test program targets.

Visual and Mechanical Inspection

Compare nameplate ampacity, voltage class, and short-circuit bracing rating against the drawings and the upstream protective device.

Inspect for physical damage, corrosion, and evidence of water — staining, rust streaks, mineral deposits at joints, and standing water in low points. Check that the run does not pass under a roof drain or condensate line.

Verify joint hardware torque with a calibrated torque wrench, or confirm the Belleville washer is compressed to the manufacturer's specification where used. Busway joints commonly use a single through-bolt with a visual torque indicator — a head that shears off at correct torque — and if the indicator head is intact the joint was never torqued.

Verify correct installation of expansion fittings where the run crosses building expansion joints or long straight runs, and that hangers permit thermal movement rather than restraining it.

Confirm enclosure grounding and bonding continuity across every joint ; the housing is the equipment grounding conductor on most busway, so a joint that is mechanically loose is also a ground-path defect.

Verify phase orientation and phasing through the run, especially where a run is fed from two directions or feeds a tie.

Confirm plug-in units are correctly latched, interlocked, and that unused openings are closed with blank covers.

Electrical Tests

Test Notes

Insulation resistance phase-to-phase and phase-to-ground Test the complete run with plug-in units and all connected apparatus removed or disconnected . One connected transformer or lighting load will dominate the reading and mask a busway problem

Contact resistance across bolted joints Micro-ohmmeter across each joint; compare joint-to-joint and phase-to-phase rather than to an absolute number

Overpotential test where specified Only per the manufacturer and NETA acceptance procedures; not routine on in-service busway

Thermographic survey under load The highest-value busway test; performed energized and loaded, ideally at 40% or more of rated load

  • Phase rotation / phasing verification Before connecting to a second source or a tie
  • Interpreting Busway IR

A busway reading is not comparable to a cable reading . The run is short, the insulation is thin barrier material, and most of the leakage path is across insulator surfaces rather than through bulk insulation. That makes busway IR highly sensitive to humidity and surface contamination and much less sensitive to length. The diagnostic value comes from three comparisons: phase-to-phase symmetry, the trend against previous tests on the same run, and the manufacturer's stated minimum. A run that read 5,000 megohms at commissioning and reads 40 megohms now has a problem even if 40 megohms sounds acceptable in isolation.

When a busway run reads low, the fastest diagnostic is sectionalizing : open a joint at the midpoint and retest each half. Two or three iterations locate the wet or contaminated section without disassembling the whole run.

Why Thermography Is Disproportionately Useful

A busway run may have dozens of bolted joints in series carrying thousands of amps. Power lost at a joint is I squared R, so at 3,000 A a joint that degrades from 10 to 60 microhms goes from 90 W to 540 W — enough to char insulation and eventually cause a phase-to-phase fault inside the housing where nobody can see it. Thermography under real load is the only test that finds this while the equipment is in service. A delta-T between one phase joint and the corresponding joints on the other two phases is the finding; absolute temperature alone is misleading because loading varies.

Outdoor Bus Structures

Domain III subdomain U covers outdoor bus structures — the open-air rigid or strain bus in a substation yard, supported on station-post or suspension insulators. There is no enclosure, so the failure modes shift from water intrusion to insulator degradation, contamination, corrosion, and hardware .

Visual and Mechanical Inspection

Insulators : cracks, chips, glaze damage, contamination and salt or industrial deposits, tracking or flashover marks, and cement growth at the caps. Check that composite insulators show no sheath splitting or corona cutting.

Conductors and connectors : rigid tubular aluminum bus for sag, damage, and corrosion; strain bus for broken strands; compression and bolted connectors for corrosion, particularly aluminum-to-copper joints , which need the correct bimetallic connector and inhibitor compound.

Expansion connectors and slip fittings free to move; the thermal excursion on outdoor bus is large.

Clearances and phase spacing verified against the design — phase-to-phase, phase-to-ground, and working clearances that will apply during maintenance.

Grounding : structure steel bonded to the ground grid, and connections to the grid intact and uncorroded.

Hardware torque verified per manufacturer values; belleville washers correctly compressed.

Check for animal and bird mitigation hardware and evidence of nesting, a leading cause of substation outages.

Electrical Tests

Insulation resistance phase-to-phase and phase-to-ground on the isolated bus section.

Contact resistance across every bolted connector, compared against the other phases and prior readings.

Thermographic survey under load , which for outdoor bus also picks up loose or corroded connectors that visual inspection cannot see.

Corona inspection (ultraviolet or corona camera) where the voltage class justifies it; corona indicates sharp edges, damaged hardware, or contamination and precedes flashover.

One field practice worth carrying into the exam: on outdoor apparatus, use the guard terminal on the megger. Surface leakage across a wet or contaminated insulator runs in parallel with the volume insulation path and produces a falsely low reading. Guarding routes that surface current around the measuring circuit and gives you the reading you actually want to trend.