Study guide
11.1 Automatic Transfer Switch Functional Testing
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
11.1 Automatic Transfer Switch Functional Testing
Key Takeaways Explain This Topic AI
An ATS functional test verifies the full source-sensing, transfer-timing, and retransfer logic — not just that the generator runs.
Open transition is break-before-make; closed transition momentarily parallels the two sources and requires an ANSI 25 synchronism-check relay with a paralleling limit under 100 ms.
The four timers to verify are failure-sensing delay (TDES), normal-to-emergency delay (TDNE), emergency-to-normal delay (TDEN), and time-delay neutral (TDN) — record each setpoint and each measured time.
Time-delay neutral lets motor back-EMF decay before the alternate source is connected, preventing out-of-phase inrush on open-transition transfers.
Document every setpoint, every transition time, the voltages/frequencies at each transition, the transition mode executed, and any alarms — with instrument IDs and calibration dates.
Last updated: August 2026
The Automatic Transfer Switch (ATS) is the brain of an emergency or standby power system. Functional testing proves the switch actually does what its controller is programmed to do — sense a normal-source failure, signal the engine-generator to start, transfer the load to the emergency source, and retransfer when normal is restored. Per ANSI/NETA ECS and NFPA 110, this sequence must be demonstrated and documented at acceptance and at scheduled maintenance intervals.
What an ATS Functional Test Verifies
An ATS functional test is not a single measurement. It verifies the complete source-sensing, timing, and switching logic: undervoltage and under/overfrequency pickup and dropout thresholds, engine start/stop contacts (start signal, cooldown stop), transfer and retransfer time delays, electrical and mechanical interlocks, and the position-indication and alarm outputs. A common Level 2 trap is to reduce "functional test" to "I pressed the test button and the generator ran" — that exercises the generator but does not validate the transfer logic. Per ANSI/NETA ATS and MTS, the functional test verifies source sensing (undervoltage and phase-loss pickup and dropout), transfer timing, and the retransfer sequence, not merely that the engine starts.
The Functional Test Sequence
The test is run with the generator in AUTO and the ATS on the normal source. Simulate the normal-source failure by dropping the sensing voltage, opening a sensing fuse, or using the controller's test function — not by killing real load without coordination.
Step Action What to verify and document
1 Confirm normal source on, ATS on normal, generator in AUTO Source voltages within pickup bands; controller shows "normal available"
2 Simulate normal failure (drop voltage/frequency or open sensing fuse) Failure-sensing delay (TDES) begins; verify dropout threshold and time
- 3 Engine start signal initiated Generator cranks and reaches rated voltage/frequency; record start time
- 4 Transfer to emergency TDNE elapses; switch transfers; record transfer time; verify load voltage
- 5 Restore normal source Normal-stabilization delay (TDEN) begins; verify voltage/frequency within band
- 6 Retransfer to normal Switch retransfers (open or closed per design); engine cooldown (TDEC) runs
- 7 Generator shutdown after cooldown Verify stop signal; controller returns to AUTO
- Open-Transition vs Closed-Transition
Open-transition (break-before-make) interrupts the load for tens of milliseconds to seconds — the normal contact opens before the emergency contact closes. Closed-transition (make-before-break) momentarily parallels the two sources so the load sees no interruption. Closed-transition retransfer requires a synchronism-check relay (ANSI 25) to verify voltage (typically within ±5 percent), frequency (within about 1 Hz), and phase angle (within about ±10 degrees) before the closing command is issued. Code limits the paralleling duration — the entire overlap must complete in under 100 milliseconds, enforced by a parallel-limit (watchdog) timer that will trip an upstream breaker if the overlap exceeds the limit. Before testing, confirm which transition type the switch uses; forcing a closed-transition retransfer with the generator off-frequency will be blocked by the 25 relay, and that block is correct behavior, not a failure.
In-Phase Monitoring
Many open-transition ATS controllers include an in-phase monitor that delays the transfer until the two sources are within a synchronism window, preventing out-of-phase closing that can destroy motor loads through residual back-EMF. If synchronism is not achieved within a set timeout (commonly 60 seconds), the controller defaults to a timed load-decay / time-delay-neutral transfer and raises a "sync fail" alarm. Document whether the in-phase path or the default path executed — a sync-fail alarm during a test is a finding, not a pass.
Timer Settings
The four timers you must verify on every ATS functional test:
Failure-sensing delay (TDES) — typically 1 to 3 seconds; prevents nuisance starts on momentary voltage dips. Too short and every sag starts the generator; too long and the emergency system misses its Type window.
Time-delay normal-to-emergency (TDNE) — engine warm-up before transfer; the load is not picked up until the generator is ready.
Time-delay emergency-to-normal (TDEN) — normal-source stabilization before retransfer; often 5 to 10 minutes on generator sets so a momentary utility return does not bounce the load back.
Time-delay neutral (TDN) — the pause in the disconnected position so motor back-EMF decays; typical default 5 seconds, range 0 to 120 seconds.
Engine cooldown (TDEC) — commonly 5 minutes; keeps the generator running unloaded after retransfer to dissipate heat before shutdown.
Record each setpoint and each measured time. A timer that fires at the wrong point is a misadjustment even if the switch "works."
What to Verify and Document
Document every setpoint, every measured time, the source voltages and frequencies at each transition, the transition mode executed (open, closed, in-phase, or default), and any alarms. NETA test reports require instrument IDs and calibration dates on every measured value. If the switch has bypass-isolation, exercise the bypass mechanism and verify the isolation interlocks. Confirm phase rotation matches between sources before any closed-transition test — wrong rotation will trip the 25 relay on retransfer or, worse, slam rotating loads into reverse when the alternate source picks them up. A factory or site acceptance test that does not exercise and document every timer, every transition, and every interlock is not a complete ATS functional test and will not satisfy ANSI/NETA ECS or NFPA 110 requirements.