Study guide
6.4 Oil Dielectric (ASTM) & DGA Sampling
NETA ETT Level II Certified Assistant Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide
2 Chapter 1: Electrical Safety
2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications
3 Chapter 2: Power Systems Theory
3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions
4 Chapter 3: Protection & Device Fundamentals
4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies
5 Chapter 4: Insulation Resistance Testing
5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography
6 Chapter 5: Withstand & Power-Factor Testing
6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating
7 Chapter 6: Transformer Testing
7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests
8 Chapter 7: CT, Relay & Motor Testing
8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables
9 Chapter 8: Switchgear & Breaker Testing
9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures
10 Chapter 9: Grounding, Batteries & Protective Devices
10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance
11 Chapter 10: Systems & Commissioning
11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow
6.4 Oil Dielectric (ASTM) & DGA Sampling
Key Takeaways Explain This Topic AI
ASTM D877 (flat-disk electrodes, 2.54 mm gap) screens new oil acceptance; D1816 (VDE mushroom electrodes, 1 or 2 mm gap with stirring) is more sensitive to moisture and particulate contamination and is preferred for in-service oil evaluation.
NETA MTS Table 100.4.1 minimums: D877 26 kV all classes; D1816 1 mm gap 23/28/30 kV; D1816 2 mm gap 40/47/50 kV for ≤69 / 69–230 / ≥230 kV equipment.
DGA sampling per ASTM D3613 requires a clean dry syringe, no trapped air, flushing the sampling port, and accurate labeling — bad sampling technique produces false conclusions.
The seven key fault gases are H2 (partial discharge), CH4/C2H6 (low-thermal), C2H4 (high-thermal), C2H2 (arcing), and CO/CO2 (cellulose/paper degradation).
The Duval Triangle plots relative percentages of CH4, C2H4, and C2H2 to classify faults into zones PD, D1, D2, T1, T2, and T3.
Last updated: August 2026
Oil Dielectric Breakdown Tests — ASTM D877 and D1816
A dielectric breakdown voltage test measures the kV at which a sample of insulating oil breaks down between two electrodes. It is the most common field screening test for oil quality — low breakdown voltage indicates water, particles, or other contamination that compromises the oil's insulating ability.
ASTM D877 — flat disk electrodes
Electrodes : flat brass disks, 25.4 mm diameter, with square edges.
Gap : 2.54 mm (0.1 in), fixed.
Voltage rise : 3 kV/s until breakdown.
Characteristics : less sensitive to moisture and particles because the flat disks do not concentrate stress at contaminants. Primarily used for new oil acceptance .
Typical minimum : 30 kV for new oil; 26 kV for in-service per NETA MTS.
ASTM D1816 — VDE mushroom electrodes
Electrodes : VDE mushroom-shaped (spherical cap), 36 mm diameter.
Gap : 1 mm or 2 mm, selectable.
Stirring : mandatory; oil is stirred during the test so particles are driven through the high-stress region.
Characteristics : significantly more sensitive to moisture, particles, and dissolved gases than D877. Preferred for in-service oil evaluation .
The 2 mm gap values are higher than the 1 mm gap values because a longer gap requires more voltage to break down the same oil.
NETA MTS Table 100.4.1 — minimum dielectric breakdown (in-service)
- Equipment voltage class D877 (kV) D1816 1 mm (kV) D1816 2 mm (kV)
- ≤ 69 kV 26 23 40
- 69 to < 230 kV 26 28 47
- ≥ 230 kV 26 30 50
D877 was removed from IEEE C57.106 in-service evaluation criteria in 2002 but is still referenced in NETA MTS with a flat 26 kV minimum across all voltage classes. For in-service oil, prefer D1816.
Dissolved Gas Analysis (DGA) Sampling Procedure
DGA is the single most diagnostic test for an oil-filled transformer. It detects incipient faults — overheating, arcing, partial discharge — by quantifying the gases dissolved in the oil before the transformer fails. The value of DGA depends entirely on sampling technique ; a poor sample produces false conclusions and unnecessary (or missed) maintenance.
Per ASTM D3613 and standard utility practice:
Use a clean, dry, sealed syringe (typically 30–50 mL) — never an open bottle for DGA. The syringe preserves dissolved gases at their in-service concentration.
Flush the sampling port — drain several liters of oil through the valve first to remove stagnant oil and any water or debris in the port. Discard the flush oil.
Fill without trapping air — purge all air from the syringe and sampling line before filling; a single air bubble contaminates the sample with atmospheric nitrogen and oxygen and dilutes the fault gases.
Sample from the correct tap — usually the lower-main-tank drain valve or a dedicated sampling valve, not a radiator or top fill port. The lower tank sample reflects the bulk oil the transformer is bathed in.
Label accurately — transformer ID, date, time, sample point, oil temperature, and weather conditions. Shipping same-day does not exempt you from labeling.
Ship promptly in a light-proof, shock-protected container.
Mixing oil from multiple transformers in one bottle, sampling from an open hatch, or skipping the flush are all disqualifying errors.
The Seven Key Fault Gases
Each fault gas is produced by a specific decomposition process. The gas signature points to the fault type.
- Gas Formula Produced by Fault signature
- Hydrogen H2 Oil/paper decomposition, partial discharge Partial discharge (corona) — mainly H2 with minor CH4
- Methane CH4 Oil decomposition, low temperature (<250°C) Low-temperature thermal fault (T1)
- Ethane C2H6 Oil decomposition, medium temperature (~250°C) Low/medium thermal fault
Ethylene C2H4 Oil decomposition, high temperature (300–700°C) High-temperature thermal fault (T2/T3) — dominant in T3
- Acetylene C2H2 Arcing (very high temperature, >700°C) Arcing (D1/D2) — significant C2H2 with H2
- Carbon monoxide CO Cellulose (paper) degradation Paper overheating / paper carbonization
- Carbon dioxide CO2 Cellulose degradation Paper aging (with CO)
- Temperature-driven formation
~150°C: H2 and CH4 begin forming.
~250°C: C2H6 starts forming.
~350°C: C2H4 starts forming.
500–700°C+: C2H2 forms (peaks near 800°C) — significant C2H2 almost always means arcing.
CO and CO2 indicate the paper insulation is involved, not just the oil.
A key rule of thumb: significant acetylene (C2H2) in a DGA is a serious alarm — it indicates arcing inside the tank and usually requires taking the transformer out of service for internal inspection.
Duval Triangle Basics
The Duval Triangle (Triangle 1) , developed by Michel Duval in 1974, is the most widely used graphical DGA interpretation method. It plots the relative percentages of three gases — CH4, C2H4, and C2H2 — on a ternary diagram:
- %CH4 = 100 × CH4 / (CH4 + C2H4 + C2H2)
- %C2H4 = 100 × C2H4 / (CH4 + C2H4 + C2H2)
- %C2H2 = 100 × C2H2 / (CH4 + C2H4 + C2H2)
The triangle is divided into fault zones:
- Zone Fault type Key gases
- PD Partial discharge H2 (Triangle 4 uses H2 for refinement)
- D1 Low-energy discharge (sparking) H2 + C2H2
- D2 High-energy discharge (arcing) H2 + C2H2, with C2H4 and CH4
- T1 Thermal fault < 300°C CH4 + C2H6
- T2 Thermal fault 300–700°C C2H4 + CH4
- T3 Thermal fault > 700°C C2H4 dominant, with H2, C2H6, traces C2H2
Duval Triangle 1 uses CH4/C2H4/C2H2; Triangle 4 uses H2/CH4/C2H6 for PD and low-thermal refinement; Triangle 5 uses CH4/C2H4/C2H6 for T2/T3 refinement. The method always produces a diagnosis (no 'unidentified' bucket), which is its strength and its weakness — boundary cases between zones still require engineering judgment.
The IEEE Std C57.104-2019 guide and IEC 60599 provide the normative interpretation framework; Duval is a complementary graphical tool.
Why Sampling Technique Matters
A DGA result is meaningless if the sample is bad. The most common errors and their effects:
Trapped air bubble — inflates N2 and O2, dilutes fault gases, can mask a real fault or trigger a false alarm on hydrogen.
Unflushed port — stagnant oil in the valve may have different gas concentrations than the bulk tank.
Wrong sample point — a radiator tap can show cooler, less-mixed oil that misses a hot-spot signature.
Open container — dissolved gases escape into the atmosphere before the lab can measure them.
The lab can detect some sampling errors (abnormally high O2, low gas totals), but it cannot correct for them. Repeat sampling is the only remedy when a sampling error is suspected.