Study guide

6.2 VLF Cable Testing & the DC/AC Voltage Conversion

NETA ETT Level II Certified Assistant Technician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NETA Level 2 Exam 1.2 The NETA Certification Hierarchy & Eligibility 1.3 Exam Administration, Scoring & Scheduling 1.4 Study Plan & How to Use This Guide

2 Chapter 1: Electrical Safety

2.1 NFPA 70E Approach Boundaries & Arc-Flash 2.2 PPE, Rubber Glove Classes & Hearing Protection 2.3 LOTO & the Electrically Safe Work Condition 2.4 Energized Work Permits & Live-Dead-Live 2.5 Temporary Protective Grounds & Induced Voltage 2.6 Hipot Testing Safety & Post-Hipot Grounding 2.7 Confined Space & General Electrical Safety 2.8 Risk Assessment, Job Briefings & the Hierarchy of Risk Controls 2.9 Codes & Standards: NFPA 70 Key Provisions and the ANSI/NETA Specifications

3 Chapter 2: Power Systems Theory

3.1 Three-Phase Power & Wye/Delta Relationships 3.2 Power Factor, Voltage Unbalance & Negative Sequence 3.3 Symmetrical Components & Fault-Current Paths 3.4 Grounding Systems & Impedance Grounding 3.5 Insulation Degradation & Dielectric Theory 3.6 Electrical Calculations, Units & Conversions

4 Chapter 3: Protection & Device Fundamentals

4.1 ANSI Device Numbers (27, 50, 51, 59, 86, 87) 4.2 IDMT/TCC Curves & Coordination 4.3 CT Theory: Ratio, Polarity, Burden, Accuracy & Knee Point 4.4 PT/VT Fundamentals & Insulation Coordination 4.5 Motor Circuits: FLA, PF Correction & Current Imbalance 4.6 One-Lines, Three-Lines, Schematics & Electrical Symbols 4.7 Short-Circuit & Coordination Studies

5 Chapter 4: Insulation Resistance Testing

5.1 Insulation Resistance: Test Voltages & IEEE 43 Minimums 5.2 Polarization Index (PI) & Dielectric Absorption Ratio (DAR) 5.3 Overpotential vs IR & Cable Hipot Basics 5.4 Guard Terminal, Doble Test Set & Thermography

6 Chapter 5: Withstand & Power-Factor Testing

6.1 DC Hipot: Step Voltage, Leakage Current & Pass Criteria 6.2 VLF Cable Testing & the DC/AC Voltage Conversion 6.3 Bushing Power Factor & Transformer PF Configurations 6.4 Oil Dielectric (ASTM) & DGA Sampling 6.5 Cable Fault Locating

7 Chapter 6: Transformer Testing

7.1 Transformer Turns Ratio (TTR) & Acceptance 7.2 Winding Resistance & Transformer Polarity 7.3 Transformer IR Configurations & Neutral-Ground Bond 7.4 SFRA, Sudden-Pressure Relay & Dry-Transformer ATS Tests

8 Chapter 7: CT, Relay & Motor Testing

8.1 CT Ratio, Polarity & Saturation Testing 8.2 Primary vs Secondary Injection & Relay Pickup 8.3 Three-Phase Relay Test Set, Phase-Angle Meter & Induction Disc 8.4 Motor Surge Test & Current Imbalance 8.5 Adjustable-Speed Drives, Reclosers, Sectionalizers & Fiber-Optic Cables

9 Chapter 8: Switchgear & Breaker Testing

9.1 Contact Resistance (Ductor) & Torque Verification 9.2 Vacuum Bottle Integrity & VCB Maintenance Tests 9.3 Post-Fault Breaker Maintenance & LV Trip-Unit Settings 9.4 Switchgear Bus IR, MCC Inspection & Bonding Jumpers 9.5 Switches, Circuit Switchers & Network Protectors 9.6 Metal-Enclosed Busways & Outdoor Bus Structures

10 Chapter 9: Grounding, Batteries & Protective Devices

10.1 Ground-Electrode Testing: Fall-of-Potential & Clamp-On 10.2 Battery Load Test (IEEE 450), VRLA Ohmic & Intervals 10.3 Fuses, GFCI & Zero-Sequence CT Grounding 10.4 Surge Arrester Acceptance & SPD Verification 10.5 Metering Devices & Regulating Apparatus 10.6 Capacitor Banks & Reactors: Inspection, Testing & Acceptance

11 Chapter 10: Systems & Commissioning

11.1 Automatic Transfer Switch Functional Testing 11.2 NFPA 110 Emergency System Load Tests 11.3 Switchgear Functional Testing & Feeder Trip Troubleshooting 11.4 Generator Paralleling & Emergency System Commissioning 11.5 As-Found / As-Left Documentation 11.6 Restoration & Handover Workflow

6.2 VLF Cable Testing & the DC/AC Voltage Conversion

Key Takeaways Explain This Topic AI

VLF (very-low-frequency) hipot tests shielded MV/HV cables at 0.1 Hz because cables are highly capacitive — a 60 Hz AC test would require impractical charging current.

IEEE 400.2 specifies VLF withstand durations of 60 minutes for installation/acceptance and 30 minutes minimum for maintenance (60 min for critical feeders).

The '62% rule' derives from 1/1.7 ≈ 0.588 ≈ 0.62: the equivalent AC RMS value of a DC test voltage is roughly 62% of the DC value, per IEEE 95 for rotating machinery.

For cables the DC/AC conversion is higher (2.0–3.0× depending on insulation), and IEEE 400 no longer recommends DC hipot for XLPE cable in service due to space-charge damage risk.

ANSI/NETA MTS-2023 now prefers VLF for MV/HV shielded cable dielectric testing; DC withstand is allowed only for laminated dielectric or extruded cables under 5 years old.

Last updated: August 2026

Why VLF for Cables

A shielded power cable is a large cylindrical capacitor. The capacitive charging current at power frequency is I = 2πfCV — directly proportional to frequency. For a long 15 kV class feeder, the 60 Hz charging current at acceptance voltage would require a test set the size of a substation transformer. Dropping the frequency to 0.1 Hz cuts charging current by a factor of 600 (0.1/60), making a portable, field-practical AC withstand test possible.

This is why very-low-frequency (VLF) hipot has become the standard field dielectric test for medium- and high-voltage shielded cables. The test applies AC stress — which replicates service conditions far better than DC — at a frequency low enough to be practical.

VLF Waveforms and Frequency

IEEE 400.2 recognizes two VLF waveforms:

Sinusoidal (0.1 Hz) — a pure sine wave; RMS = 0.707 × peak (assuming <5% harmonic distortion). Most modern VLF sets produce this.

Cosine-rectangular (0.1 Hz) — alternates positive and negative half-cycles with a cosine shape; for this waveform RMS and peak are treated as equal, so the same numeric voltage produces a higher peak stress.

The standard test frequency is 0.1 Hz . Frequencies from 0.01 to 0.1 Hz are acceptable, but 0.1 Hz is the norm; lower frequencies extend the test duration per cycle and are used only when 0.1 Hz still draws too much current on very long cables.

VLF Test Duration (IEEE 400.2)

  • Test category Minimum duration at 0.1 Hz
  • Installation (temporary terminations) 60 minutes
  • Acceptance (new cable, final terminations) 60 minutes
  • Maintenance (aged cable) 30 minutes; 60 minutes for critical/feeder circuits

The 60-minute acceptance duration is not arbitrary — IEEE 400.2 research showed that cables with installation defects break down within the first minutes, while trees and aging-related weak spots often need the full duration to fail under VLF stress.

IEEE 400.2 VLF Test Voltages (Table 3, 2023)

Selected values from IEEE 400.2-2023 Table 3, phase-to-ground:

Cable rating (kV, L-L) Sinusoidal acceptance (kV RMS) Cosine-rect. acceptance (kV peak) Sinusoidal maintenance (kV RMS)

  • 5 10 14 7
  • 15 21 30 16
  • 25 32 45 24
  • 35 44 62 33
  • 46 57 81 43
  • 69 84 119 63

Maintenance voltage is approximately 75% of acceptance voltage . The 2024 revision expanded cable coverage to 138 kV and now references only RMS values (peak values removed for consistency).

The 62% DC/AC Conversion Factor (IEEE 95) — Not the Ground-Test 62% Rule

The 62% rule is a DC-to-AC conversion shortcut. (Note: this 62% rule is a DC-to-AC voltage conversion factor from IEEE 95 — it is unrelated to the 62% rule used in fall-of-potential ground-electrode resistance testing, covered in Section 10.1. Do not confuse the two.) IEEE Std 95 establishes the relationship V_DC = 1.7 × V_AC(rms) for rotating machinery acceptance tests. Taking the reciprocal:

V_AC(rms) ≈ V_DC / 1.7 ≈ 0.588 × V_DC ≈ 0.62 × V_DC

So the equivalent AC RMS value of a given DC test voltage is roughly 62% of the DC value . Equivalently, if you have an AC RMS test specification and want the DC equivalent, multiply by 1.7 (≈ 1/0.62).

Where the 62% rule applies

Rotating machinery — directly from IEEE 95; the 1.7× factor was chosen as a conservative compromise for complete windings.

General AC/DC hipot planning — useful for converting between published AC and DC test values when a single standard governs both.

Where the 62% rule does NOT apply

Cables — the historical DC/AC ratio for cables is 2.0 to 3.0× depending on insulation type (rubber, paper, polyethylene), not 1.7×. The 62% rule under-predicts the DC equivalent for cables.

XLPE cable in service — IEEE 400 and IEEE 400.2 no longer recommend DC hipot for extruded (XLPE/EPR) cables after 5 years in service. Space charge accumulates under DC stress and can damage the cable when voltage is removed. VLF is the preferred method.

Laminated dielectric (PILC) cable — DC hipot is still accepted.

A common mistake is applying the 62% rule to a cable pressure test. The rule is a rotating-machinery conversion; cable DC voltages come from IEEE 400 / NETA ATS cable tables, not from a 1.7× multiplier.

MTS Frequency vs ATS Acceptance

ANSI/NETA ATS (Acceptance Testing Specification) governs new equipment acceptance — first commissioning after install or rewind. ANSI/NETA MTS (Maintenance Testing Specifications) governs in-service maintenance testing.

For cable, the practical differences:

ATS — higher test voltages (acceptance column of IEEE 400.2 Table 3); 60-minute duration.

MTS — maintenance voltage ≈ 75% of acceptance; 30-minute minimum (60 min for critical circuits). MTS-2023 added Tan Delta tables for XLPE and EPR and now prefers VLF for all MV/HV shielded cable dielectric tests.

MTS also defines frequency of maintenance intervals based on application criticality and environment — typically 1–3 years for cable feeders, shorter in harsh or critical-service environments.

Common VLF Traps

Confusing cosine-rectangular peak with sinusoidal RMS — the two waveforms use different voltage scales for the same cable class (e.g., 35 kV class: 44 kV RMS sinusoidal vs 62 kV peak cosine-rectangular). Mixing them up over-tests or under-tests the cable.

Shortening the 60-minute acceptance duration — IEEE 400.2 research showed aging-related trees can take the full duration to break down; cutting the test to 15 minutes can pass a defective cable.

Applying the 62% rule to a cable DC test — the 62% factor is a rotating-machinery conversion; cable DC/AC ratios are 2.0–3.0× and IEEE 400 no longer recommends DC for in-service XLPE anyway.

Ignoring MTS-2023's preference for VLF — DC withstand is allowed only for laminated dielectric or extruded cables under 5 years old; everything else should use VLF.