Study guide
5.2 Risk Assessment, Risk Matrix & ALARP Basics
ISPON HSE Level 1 Basic HSE
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Eligibility, Training Pathway & ISPON Registration 1.3 Study Strategy & Content Blueprint
2 HSE Fundamentals & Management Basics
2.1 HSE Definitions, Philosophy & Core Principles 2.2 Safety Policy & HSE Management System Basics 2.3 Roles and Responsibilities (Employer, Employee, Safety Officer)
3 Nigerian HSE Law & Professional Regulation
3.1 ISPON Act 2014 & Professional Regulation 3.2 Factories Act LFN 2004 & Related Nigerian HSE Law 3.3 HSE in Nigerian Industry Context
4 Hazard Identification Fundamentals
4.1 Hazard vs Risk Fundamentals 4.2 Types of Workplace Hazards 4.3 Unsafe Acts vs Unsafe Conditions
5 Risk Management, HEMP & Controls
5.1 Hazard and Effects Management Process (HEMP) 5.2 Risk Assessment, Risk Matrix & ALARP Basics 5.3 Hierarchy of Controls 5.4 Job Safety Analysis (JSA) Basics
6 Accident Causation & Investigation
6.1 Heinrich's Domino Theory 6.2 Swiss Cheese Model & System Failures 6.3 Incident Classification, Reporting & Investigation Basics
7 Safety Culture & Accident Prevention
7.1 Safety Culture & Behavioural Safety 7.2 Leading vs Lagging Indicators & Toolbox Talks 7.3 Accident Prevention Strategies & Near Misses
8 Fire Safety & Emergency Response
8.1 Fire Chemistry: Triangle and Tetrahedron 8.2 Fire Classes (BS EN 2) 8.3 Fire Extinguishers: Types, Color Codes & PASS 8.4 Emergency Response: RACE & Evacuation
9 Occupational Health & Environmental Hygiene
9.1 Housekeeping & Workplace Hygiene 9.2 Personal Protective Equipment (PPE) 9.3 Manual Handling Techniques 9.4 Ergonomics, Noise Limits & Basic Environmental Awareness
10 Basic First Aid & CPR Awareness
10.1 First Aid Principles & Kit Contents 10.2 Primary Survey (ABC) 10.3 CPR Awareness (30:2) 10.4 Bleeding Control, Shock Management & Recovery Position
5.2 Risk Assessment, Risk Matrix & ALARP Basics
Key Takeaways Explain This Topic AI
Risk is commonly expressed as Risk = Likelihood × Severity (how likely harm is multiplied by how bad the consequences would be).
Qualitative risk matrices plot likelihood against severity on a grid so teams can classify risk as low, medium, or high and prioritise action.
Residual risk is the risk that remains after controls are applied; assessment should consider both initial and residual risk.
ALARP (As Low As Reasonably Practicable) means reducing risk until further reduction would be grossly disproportionate to the benefit—Level 1 awareness, not full legal analysis.
Stop work and escalate when risk is intolerable, controls are missing or failed, or conditions change beyond the assessment.
Last updated: July 2026
5.2 Risk Assessment, Risk Matrix & ALARP Basics
Once hazards and effects are identified (HEMP Step 1), you must assess risk (HEMP Step 2). Assessment turns a long hazard list into a priority list : what must be controlled before work starts, what can be managed with standard rules, and what is intolerable until conditions change. For ISPON HSE Level 1, master the formula Risk = Likelihood × Severity , the idea of a risk matrix , residual risk , basic ALARP awareness, and stop-work / escalate rules.
Risk = Likelihood × Severity
Risk is not the same as hazard . A hazard is the source of potential harm. Risk describes how big the problem is in practice , combining:
Likelihood (probability) — how often or how probable it is that the hazard will cause the unwanted event
Severity (consequence) — how bad the effects would be if the event occurred (injury, ill health, fatality, environmental damage, major asset loss)
In words used across Nigerian training rooms:
Risk = Likelihood × Severity
Implications you must understand:
A rare event with catastrophic severity can still be high risk (for example, major hydrocarbon fire).
A frequent event with minor severity can be medium risk and still deserve controls (for example, repeated minor cuts from poor housekeeping).
Reducing either likelihood or severity reduces risk; the best programmes often reduce both.
Component Questions assessors ask Example factors
Likelihood How often could this happen here? Exposure frequency, condition of equipment, competence, history of near misses
Severity How bad if it happens? Energy level, number of people exposed, toxicity, fire/explosion potential, environmental sensitivity
Qualitative Risk Assessment
At Level 1, risk assessment is usually qualitative or semi-quantitative : people use words and simple scores (low/medium/high or 1–5 scales), not complex probabilistic models. A typical simple process:
Describe the task and location.
List hazards and who/what could be harmed.
Estimate likelihood without adequate controls (initial risk).
List existing and planned controls.
Estimate residual risk after controls.
Decide: proceed, add controls, or stop/escalate.
Record and communicate (toolbox talk, JSA, permit).
Assessment should be team-based when possible. Operators and craft workers often know real failure modes that a desk-only assessment misses—especially on Nigerian sites where conditions change with weather, contractor mix, and production pressure.
The Risk Matrix
A risk matrix is a grid with likelihood on one axis and severity on the other. Each cell is coloured or labelled (for example green/yellow/red or low/medium/high) to show risk level. Matrices help teams:
- Compare different hazards on a common scale
- Agree when risk is acceptable with controls
- Show supervisors and clients why extra barriers are needed
- Train new workers on what "high risk" looks like
Companies use different sizes (3×3, 4×4, 5×5). Learn the logic , not one company's exact colour rules. On exam day, apply the matrix you are given in the question stem.
Simple 5×5 Matrix Example (Illustrative)
Likelihood scale (example):
- Score Likelihood label Meaning (plain language)
- 1 Rare May occur only in exceptional circumstances
- 2 Unlikely Could occur sometime, but not expected often
- 3 Possible Might occur at some time under current conditions
- 4 Likely Will probably occur in most circumstances if unchecked
- 5 Almost certain Expected to occur frequently without control
Severity scale (example):
- Score Severity label Typical consequence band
- 1 Negligible First aid only; trivial environmental effect
- 2 Minor Medical treatment; limited local impact
- 3 Moderate Lost-time injury; moderate spill or damage
- 4 Major Permanent disability / serious injury; major spill
- 5 Catastrophic Fatality / multiple fatalities; disaster-level release
Illustrative risk score = Likelihood score × Severity score (range 1–25):
- L \ S 1 Negligible 2 Minor 3 Moderate 4 Major 5 Catastrophic
- 5 Almost certain 5 10 15 20 25
- 4 Likely 4 8 12 16 20
- 3 Possible 3 6 9 12 15
- 2 Unlikely 2 4 6 8 10
- 1 Rare 1 2 3 4 5
Example banding (site-specific; for learning only):
- Score band Risk level Typical action
- 1–4 Low Monitor; standard controls and good housekeeping
- 5–9 Medium Specific controls required; supervisor awareness
- 10–16 High Senior review; robust controls before work; consider stop
- 17–25 Extreme / intolerable Do not proceed until risk reduced; escalate
Worked example: Working in an unsupported deep excavation.
- Severity if collapse occurs: 5 (catastrophic)
- Likelihood without shoring/battering and controls: 4 (likely) on unstable soil after rain
- Initial score: 4 × 5 = 20 (extreme) → do not enter; engineer controls first
After proper shoring, access control, and inspection: likelihood drops to 1–2 → residual score much lower, work may proceed under permit and supervision
Residual Risk
Initial (inherent) risk is the risk before additional controls (or with only weak existing controls). Residual risk is what remains after controls are applied. No real workplace has zero residual risk. The goal is residual risk that is tolerable under company standards and ALARP thinking.
- Concept Meaning Level 1 question
- Initial risk Risk picture without adequate controls "How bad is it if we do nothing extra?"
- Controls Barriers that reduce L and/or S "What will we put in place?"
- Residual risk Risk left after controls "Is it now low enough to proceed?"
If residual risk is still high or extreme, add stronger controls or do not do the task that way. PPE alone rarely turns extreme risk into low residual risk for high-energy hazards.
ALARP at Level 1 Awareness
ALARP means As Low As Reasonably Practicable . It is a risk-management principle: keep reducing risk until the cost, time, and effort of further reduction would be grossly disproportionate to the extra safety benefit gained. At Basic HSE depth, know these points:
ALARP does not mean "as low as we can afford this week if we are in a hurry."
ALARP does not mean zero risk or absolute safety.
ALARP does mean serious, proportionate effort—especially for high-severity hazards.
Documented assessment, hierarchy of controls, and competent judgement support ALARP decisions.
For Level 1 workers, the practical translation is: use effective controls that are reasonable for the risk; do not accept high residual risk just because fixing it is inconvenient.
You are not expected to perform full cost-benefit legal arguments on the exam. You are expected to recognise that "reasonably practicable" implies real effort, not empty paperwork.
When to Escalate and When to Stop Work
Every Level 1 worker should know stop-work authority in spirit: if conditions are immediately dangerous or the assessment is no longer valid, pause the job and call supervision/HSE.
Stop work / do not start when:
- Risk is assessed as high/extreme and agreed controls are not in place
- Required permits, isolations, gas tests, or competent persons are missing
- Equipment is defective (for example damaged lifting gear, broken scaffold components)
- Weather or process conditions create a new high-severity scenario
- You are asked to bypass a critical safety device without authorised procedure
- People are impaired (fatigue, alcohol/drugs) for safety-critical tasks
Escalate when:
- You cannot reduce residual risk with resources available at crew level
- There is disagreement about severity (for example possible H₂S, structural instability)
- A near miss shows controls are weaker than assumed
- Client, community, or environmental exposure expands beyond the original plan
- Situation Worker action
- Controls match the JSA/permit and residual risk is acceptable Proceed with vigilance
- Condition changes mid-task Pause, reassess, update controls
- Pressure to "just finish quickly" without barriers Stop and escalate; production does not override life safety
- Unsure about gas test or isolation status Treat as unsafe until competent confirmation
- Common Exam Traps
- Treating a hazard as already a quantified risk without likelihood and severity thinking
- Assuming low likelihood always means low risk even when severity is catastrophic
- Forgetting residual risk after naming controls
- Confusing ALARP with "ignore expensive controls forever"
- Continuing work when the matrix would show intolerable risk
- Exam Focus
You will see formula items ( Risk = Likelihood × Severity ), matrix interpretation (which cell is higher risk), residual-risk scenarios, and ALARP definitions at awareness level. Link assessment back to HEMP: assessment prioritises where Control and Recover effort must go.