Study guide

2.2 Safety & Hazard Management

NHA Certified Phlebotomy Technician CPT

Track your progress as you read

Finished sections get a check mark.

1 Introduction & NHA CPT Exam Overview

1.1 NHA CPT Exam Facts 1.2 Eligibility & Application 1.3 Test Plan & Study Strategy

2 Safety & Compliance

2.1 Infection Control & Standard Precautions 2.2 Safety & Hazard Management 2.3 Regulatory Compliance & Quality

3 Patient Preparation

3.1 Patient Identification & Communication 3.2 Pre-Analytical Variables 3.3 Vascular Anatomy & Site Selection

4 Routine Blood Collections

4.1 Equipment & Tube Selection 4.2 Venipuncture Technique 4.3 Capillary Collection & Complications

5 Special Collections & Processing

5.1 Special Collections I 5.2 Special Collections II & Special Populations 5.3 Specimen Processing & Handling

6 Final Review & Test-Day Strategy

6.1 High-Yield Recap 6.2 Order-of-Draw & Scenario Drills 6.3 Test-Day Strategy & Pitfalls

2.2 Safety & Hazard Management

Key Takeaways Explain This Topic AI

Never recap, bend, break, or shear a contaminated needle; activate the engineered safety device and discard the unit immediately at point of use.

Sharps containers must be rigid, puncture-resistant, leak-proof, closable, biohazard-labeled, and replaced when about three-quarters full.

After a needlestick, wash the site with soap and water immediately, then report the incident for post-exposure evaluation — do not delay.

On the safety hierarchy, engineering controls (e.g., self-sheathing needles) rank above work-practice controls because they remove the hazard rather than relying on behavior.

A Safety Data Sheet (SDS) must be readily accessible for every hazardous chemical in the workplace under OSHA's Hazard Communication Standard.

Last updated: May 2026

Roughly one-quarter of Safety and Compliance items deal with hazard management — the concrete actions you take with sharps, spills, and chemicals. These questions are highly procedural; the NHA CPT exam wants the single best immediate action .

Sharps Safety and Disposal

A contaminated sharp is any object that can penetrate skin (needles, lancets, broken glass tubes). The leading cause of bloodborne pathogen exposure is the needlestick , and most occur during or after needle disposal.

Rules tested heavily on the exam:

Never recap, bend, break, shear, or remove a contaminated needle by hand. Recapping is the classic wrong answer.

Activate the engineered safety feature immediately after withdrawal, using a one-handed technique.

Discard the needle/holder as one unit at the point of use — do not carry it to a distant container.

Keep the sharps container within arm's reach before you begin the draw.

Sharps Container Requirements

  • Requirement Specification
  • Construction Rigid, puncture-resistant, leak-proof on sides and bottom
  • Closure Closable and sealable for transport
  • Labeling Biohazard symbol and color-coded (red)
  • Fill level Replace when approximately three-quarters (3/4) full — never overfill
  • Placement As close as practical to the point of use, upright, secured
  • Needlestick and Exposure Response

When an exposure incident occurs (needlestick, splash to mucous membranes, blood on non-intact skin), the response order is fixed and frequently tested:

Decontaminate immediately — wash a percutaneous wound with soap and water; flush mucous membranes (eyes, nose, mouth) with water or saline.

Report the incident to the supervisor right away.

Seek post-exposure medical evaluation — OSHA requires a free, confidential evaluation, source-patient testing where permitted, baseline testing, and follow-up.

Document the route of exposure and circumstances in the incident report.

The first action is always to wash/flush the site — not to find the supervisor first, and not to squeeze the wound (no evidence it helps, and it can cause trauma).

Biohazard Handling and Spill Cleanup

Regulated medical (biohazard) waste — blood-soaked materials, used tubes, and sharps — goes into red biohazard bags or labeled containers , separated from regular trash. Do not overfill bags, and transport them sealed.

Blood Spill Cleanup Sequence

Put on appropriate PPE (gloves; add gown/eye protection for large spills).

Absorb and remove visible organic material with absorbent paper towels first — disinfectant works poorly through a thick blood layer.

Disinfect the area with an EPA-registered tuberculocidal disinfectant or a fresh 1:10 dilution of household bleach (sodium hypochlorite) .

Allow the required wet contact time , then wipe and dispose of all materials as biohazard waste.

Perform hand hygiene after removing PPE.

  • Fire, Electrical, and Chemical Safety
  • Fire Safety

Memorize two acronyms:

RACE — R escue anyone in danger, A larm (pull and call), C onfine the fire (close doors), E xtinguish or E vacuate.

PASS — P ull the pin, A im at the base of the fire, S queeze the handle, S weep side to side.

The class A fire is ordinary combustibles, class B is flammable liquids, class C is electrical, and class D is combustible metals. A class ABC extinguisher is multipurpose and common in labs.

Electrical Safety

Unplug a malfunctioning or smoking instrument, do not use damaged cords, avoid daisy-chained power strips, and never use water on an energized electrical fire (use a class C or ABC extinguisher).

Chemical Safety and the SDS

Under OSHA's Hazard Communication Standard , every hazardous chemical must have a Safety Data Sheet (SDS) that is readily accessible to all employees. The SDS follows a standardized 16-section format covering identification, hazards, first aid, handling/storage, and spill response. Secondary containers must be labeled, and incompatible chemicals must be stored apart.

Engineering vs. Work-Practice Controls

OSHA defines a hierarchy of controls . The exam expects you to know that engineering controls outrank work-practice controls because they physically remove or isolate the hazard rather than depending on a person to behave correctly every time.

Control Type Definition Phlebotomy Examples

Engineering controls Isolate or remove the hazard at its source Self-sheathing/retractable needles, safety lancets, sharps containers, splash guards

Work-practice controls Change how a task is performed to reduce exposure No recapping, one-handed scoop only if unavoidable, no eating/drinking in the lab, hand hygiene

PPE Last layer — a barrier worn on the body Gloves, gown, mask, eye protection

If a question asks for the most effective way to prevent needlesticks, the best answer is the engineering control (a safety-engineered sharps device), not a work-practice rule or PPE.