Study guide

12.3 Task Appropriate Mode (TAM)

Nautical Institute DP Operator DPO

Track your progress as you read

Finished sections get a check mark.

1 Introduction & NI Scheme

1.1 Current Exam Facts 1.2 Phases A–E Pathway 1.3 Certificates, Eligibility & Revalidation

2 DP Principles Fundamentals

2.1 What is Dynamic Positioning & Degrees of Freedom 2.2 Seven Components of a DP System 2.3 The DP Operator & Human-Machine Interface

3 Controller, Model & Environmental Sensors

3.1 DP Controller & Mathematical Model 3.2 Kalman Filtering & Current Estimation 3.3 Gyrocompass & Heading Feedback 3.4 Wind Sensor, MRU & UPS

4 GNSS & Acoustic Position References

4.1 DGNSS & Differential Correction 4.2 Relative GNSS / RTK Concepts 4.3 Hydroacoustics USBL/SSBL 4.4 Long Baseline (LBL) Systems

5 Relative PRS, Selection & Voting

5.1 Light Taut Wire 5.2 Laser Relative References (Fanbeam/CyScan) 5.3 Radar/Microwave Relative References (RadaScan) 5.4 Reference Selection, Voting & Common-Mode Failure

6 Power Generation & PMS

6.1 Diesel-Electric Power Architecture 6.2 Power Management System 6.3 Load Sharing, Load Shedding & Spinning Reserve

7 Bus Configuration & Power Failures

7.1 Open vs Closed Bus-Tie 7.2 Blackout & Blackout Recovery 7.3 Drive-Off vs Drift-Off

8 Thrusters & Allocation

8.1 Tunnel, Azimuth & Retractable Thrusters 8.2 Thrust Allocation, Forbidden Zones & Bias 8.3 Thruster Interaction & Faulty Thruster Response

9 Control Modes

9.1 Auto DP Mode 9.2 Joystick & Independent Joystick System 9.3 Mode Selection & Practical Setup

10 DP Equipment Classes

10.1 IMO Equipment Classes 1, 2 and 3 10.2 MSC.1/Circ.1580 vs MSC/Circ.645 10.3 Sensor Redundancy & 2-out-of-3 Voting

11 FMEA, Worst Case Failure & Consequence Analysis

11.1 FMEA & Annual DP Trials 11.2 Worst Case Failure 11.3 Consequence Analysis

12 ASOG, CAM & TAM

12.1 Activity Specific Operating Guidelines (ASOG) 12.2 Critical Activity Mode (CAM) 12.3 Task Appropriate Mode (TAM)

13 Capability Plots & Approach Planning

13.1 DP Capability Plots 13.2 Footprint Plots & Weather-Optimal Heading 13.3 500 m Zone Approach & Escape Routes

14 Watchkeeping & Industry Guidance

14.1 Watchkeeping & Handover 14.2 Checklists, Alarms & Time to Terminate 14.3 IMCA M103/M117 Guidance Context

15 Integrated Operations & Assessment Strategy

15.1 Multi-System Failure Scenarios 15.2 Integrated Operations Case Studies 15.3 Induction Assessment Strategy

12.3 Task Appropriate Mode (TAM)

Key Takeaways Explain This Topic AI

Task Appropriate Mode (TAM) is a configuration in which a single failure may exceed residual capability after the design WCF and could cause loss of position — accepted only when task risk allows it

TAM is an intentional efficiency and flexibility trade-off, not accidental plant neglect; it still requires company approval, documentation, and clear abort criteria

Typical TAM uses include open-water standby, low-consequence holding, or transit-related DP where excursion risk is acceptable

CAM prioritises post-WCF position-keeping; TAM may accept higher common-mode or reduced-redundancy risk for lower-consequence tasks

Exam scenarios hinge on matching mode to consequence: divers/close work → CAM; low-risk standby with approval → TAM may be justified

Last updated: July 2026

Not every DP hour is a dive under a platform

If CAM were mandatory for every minute a thruster was in auto, vessels would burn unnecessary fuel, accumulate hours, and still not improve safety when the task risk is low. Task Appropriate Mode (TAM) exists for that reality: configure the plant appropriately for the task , even when that configuration would not guarantee position-keeping after the design worst-case single failure.

TAM is often misunderstood as “lazy CAM” or “broken redundancy.” Correct teaching treats TAM as a conscious, authorised risk decision with documentation — the counterpart to CAM, not its careless cousin.

TAM definition (exam-stable)

In TAM , the DP system may be configured such that a single failure could exceed the residual capability associated with the usual WCF case and could cause loss of position . That risk is accepted because the consequence of an excursion for the present task is judged acceptable (open water, no divers, no close structure, recoverable delay).

  • TAM is… TAM is not…
  • Task-matched configuration with accepted higher residual risk Automatic permission to dive with one thruster
  • Often more fuel-efficient (fewer gensets, sometimes closed bus) Proof that Class 2 notation was cancelled
  • Documented and approved under company procedures A silent DPO decision to ignore standing orders
  • Still monitored with an ASOG (usually looser bands) “No procedures needed”
  • Reversible — escalate to CAM when the task becomes critical A permanent lifestyle for all offshore work

Important

Exam trap: “TAM is more redundant than CAM.” False. TAM generally accepts less residual protection relative to critical-work CAM. Another trap: “TAM is only used during annual DP trials.” TAM is an operational mode for lower-risk tasks, not a trials-only label.

Why companies allow TAM

Driver Explanation

Consequence Open-water standby excursion may only mean a larger footprint and a restart — not fatality or platform contact

  • Efficiency Fewer online generators, possible closed bus, reduced thruster bias lower fuel and maintenance
  • Flexibility Industrial loads and hotel demand can share a common plant more easily

Human factors Clear modes prevent “everything is always maximum CAM” fatigue and cynicism when risk is truly low

Honest risk management Better to name accepted risk than to claim CAM while running a minimal plant

The key word is accepted . TAM without approval, without ASOG, and without understanding post-failure drift risk is just under-configured DP .

Typical TAM plant picture

Vessel procedures differ, but exam-level contrasts with CAM are:

  • Element Often in CAM Often acceptable in TAM (if authorised)
  • Bus-tie Open / proven isolation Closed bus for shared reserve (know blackout cascade risk)
  • Generators online High count / high reserve Fewer sets matched to average load + some reserve
  • Thrusters Maximum practical residual set May allow lower online thruster count if task risk allows
  • PRS Multiple independent families May accept fewer references when excursion is tolerable
  • Weather limits Conservative vs theoretical capability May use wider bands if open water and abort is easy
  • Fuel / wear Higher Lower
  • After single failure Still keep position May lose position — planned contingency

TAM does not mean disable all references, trip all generators, or abandon watchkeeping. It means the redundancy bar is set to the task, and the crew has thought through “if we black one side or lose a thruster group, we may drift — and that is acceptable here.”

Contrast table: CAM vs TAM (memorise)

Dimension CAM TAM

Primary goal Survive WCF without loss of position during critical work Match configuration to lower task risk / efficiency needs

Post-single-failure position Must remain within limits May be lost / large excursion accepted

Typical activities Diving, close proximity, critical heavy-lift phase Open-water standby, low-risk holding, some transit DP

  • Power philosophy Partitioned, high online reserve May share bus and run leaner generation
  • Fuel cost Higher Lower
  • ASOG tightness Strict equipment and weather rows Wider limits, still colour-coded
  • Approval Default for high-consequence work Requires company/task approval when below critical redundancy

Exam decision rule High human/asset collision consequence → CAM Low consequence + authorised efficiency → TAM possible

Intentional and documented — the non-negotiables

For TAM to be legitimate:

Task risk assessment shows excursion is acceptable (no divers in water, adequate sea room, no SIMOPS that turn drift into disaster).

Company procedure allows TAM for this activity class.

Master / DP authority (and client if required) approve the mode.

Configuration is logged — bus state, gensets, thrusters, PRS, defects.

ASOG for the task is active with clear red abort criteria (weather, proximity change, start of critical phase).

Trigger to leave TAM is pre-agreed — e.g. “on dive bell run, switch to CAM and verify before lock-out.”

Crew briefing so nobody assumes CAM residual when the plant is TAM-lean.

If any of those are missing, examiners and incident investigators will treat the setup as uncontrolled degradation , not TAM.

Exam scenarios: choosing the mode

Scenario 1 — Divers deployed. Always CAM (or stricter). TAM’s acceptance of post-failure loss of position is incompatible with divers in the water.

Scenario 2 — Open-water ROV standby 5 nm from nearest asset, calm weather, company TAM procedure. TAM may be justified: fewer gensets, possibly closed bus, documented ASOG. If ROV moves into a structure’s 500 m zone for close inspection, escalate to CAM before the critical approach.

Scenario 3 — Heavy lift. Approach and rigging may allow elevated readiness; the critical lift phase is CAM. After the load is secure and clear, documented return to TAM may be allowed for standby.

Scenario 4 — “Fuel saving” inside the 500 m zone. Candidate chooses TAM with reduced redundancy under the platform. Wrong. Proximity hazard demands CAM-type residual protection regardless of fuel price.

Scenario 5 — Generator trip in TAM. Position may start to degrade more than CAM would allow. Correct response is still ASOG-driven : assess whether residual risk remains acceptable; if not, restore plant or abort the (even low-risk) task and move clear. TAM is not “ignore failures.”

Scenario 6 — Mislabelled mode. Bridge says TAM but worksite starts diving without reconfiguration. That is an operational control failure . Mode labels must track real activity phase changes.

Operator decision flow (simple) Is a position excursion after single failure unacceptable

(divers, close structure, critical lift geometry, client mandate)?

  • │
  • ├─ YES → CAM (+ tight ASOG) → verify plant residual → start critical work
  • │

└─ NO → Is company TAM allowed and approved for this task?

  • │
  • ├─ YES → Configure TAM, document, brief, use TAM ASOG
  • │ Watch for task creep → re-enter CAM when risk rises
  • └─ NO → Default to CAM / higher redundancy until approved otherwise
  • Worked comparison narrative

A DP construction vessel spends the morning in open water calibrating systems. Engineers run a lean generator set and closed bus under TAM ; ASOG weather limits are wide; an excursion would only delay the schedule. At midday the vessel enters the 500 m zone for platform approach. Before the approach checklist completes, the DPO and Master exit TAM : open bus-ties, start additional gensets, enable full PRS set, activate the proximity CAM ASOG . After work, clear of the zone, they may return to TAM with a logged decision. The skill is mode switching with activity phase , not permanent loyalty to either label.

Exam traps for TAM items

  • Trap Correct framing
  • TAM more redundant than CAM TAM usually accepts greater post-failure risk
  • TAM = no references References still used; redundancy bar may be lower
  • TAM only for DP trials TAM is operational for lower-risk tasks
  • TAM needs no documentation TAM must be approved and logged
  • TAM allows diving if weather is nice Diving / high consequence → CAM
  • Closed bus blackout risk disappears in TAM Risk remains; it is accepted , not eliminated
  • “Position holding now” proves TAM safe forever Task change or weather rise can invalidate TAM
  • Linking TAM to ASOG and CAM

ASOG still governs yellow/red actions in TAM; bands differ, discipline does not.

CAM is the default mental model when consequence is high; TAM is the authorised exception when consequence is low.

WCF / consequence analysis still matter: in TAM you may accept a warning that WCF would lose position — but you must know that is the deal, not discover it after divers lock out.

Power chapters (open/closed bus, spinning reserve) supply the technical content of what you are accepting.

Bottom line: TAM intentionally accepts that a single failure may exceed residual capability and cause loss of position when the task risk allows it. It is an efficiency and flexibility mode that remains deliberate, approved, and documented , with an ASOG and a clear path back to CAM when the work becomes critical. On the exam, match the mode to consequence , not to fuel price alone.