Study guide
7.2 Blackout & Blackout Recovery
Nautical Institute DP Operator DPO
Track your progress as you read
Finished sections get a check mark.
1 Introduction & NI Scheme
1.1 Current Exam Facts 1.2 Phases A–E Pathway 1.3 Certificates, Eligibility & Revalidation
2 DP Principles Fundamentals
2.1 What is Dynamic Positioning & Degrees of Freedom 2.2 Seven Components of a DP System 2.3 The DP Operator & Human-Machine Interface
3 Controller, Model & Environmental Sensors
3.1 DP Controller & Mathematical Model 3.2 Kalman Filtering & Current Estimation 3.3 Gyrocompass & Heading Feedback 3.4 Wind Sensor, MRU & UPS
4 GNSS & Acoustic Position References
4.1 DGNSS & Differential Correction 4.2 Relative GNSS / RTK Concepts 4.3 Hydroacoustics USBL/SSBL 4.4 Long Baseline (LBL) Systems
5 Relative PRS, Selection & Voting
5.1 Light Taut Wire 5.2 Laser Relative References (Fanbeam/CyScan) 5.3 Radar/Microwave Relative References (RadaScan) 5.4 Reference Selection, Voting & Common-Mode Failure
6 Power Generation & PMS
6.1 Diesel-Electric Power Architecture 6.2 Power Management System 6.3 Load Sharing, Load Shedding & Spinning Reserve
7 Bus Configuration & Power Failures
7.1 Open vs Closed Bus-Tie 7.2 Blackout & Blackout Recovery 7.3 Drive-Off vs Drift-Off
8 Thrusters & Allocation
8.1 Tunnel, Azimuth & Retractable Thrusters 8.2 Thrust Allocation, Forbidden Zones & Bias 8.3 Thruster Interaction & Faulty Thruster Response
9 Control Modes
9.1 Auto DP Mode 9.2 Joystick & Independent Joystick System 9.3 Mode Selection & Practical Setup
10 DP Equipment Classes
10.1 IMO Equipment Classes 1, 2 and 3 10.2 MSC.1/Circ.1580 vs MSC/Circ.645 10.3 Sensor Redundancy & 2-out-of-3 Voting
11 FMEA, Worst Case Failure & Consequence Analysis
11.1 FMEA & Annual DP Trials 11.2 Worst Case Failure 11.3 Consequence Analysis
12 ASOG, CAM & TAM
12.1 Activity Specific Operating Guidelines (ASOG) 12.2 Critical Activity Mode (CAM) 12.3 Task Appropriate Mode (TAM)
13 Capability Plots & Approach Planning
13.1 DP Capability Plots 13.2 Footprint Plots & Weather-Optimal Heading 13.3 500 m Zone Approach & Escape Routes
14 Watchkeeping & Industry Guidance
14.1 Watchkeeping & Handover 14.2 Checklists, Alarms & Time to Terminate 14.3 IMCA M103/M117 Guidance Context
15 Integrated Operations & Assessment Strategy
15.1 Multi-System Failure Scenarios 15.2 Integrated Operations Case Studies 15.3 Induction Assessment Strategy
7.2 Blackout & Blackout Recovery
Key Takeaways Explain This Topic AI
A DP blackout is total (or effective total) loss of main electrical power to the switchboard(s) and thrusters — not merely loss of references or a single sensor
UPS keeps DP computers, selected sensors, and control networks alive for a limited time so the control system can ride through and support recovery
Recovery priorities: restore generation and bus power, restart thrusters carefully, then re-enable PRS and full Auto DP without thruster surge
Prevent thruster surge on recovery by checking modes, gains, setpoints, thruster enables, and power limits before demanding full force
Operator procedures and engineer coordination matter as much as automation: abort critical work, communicate, recover power first, then position control
Last updated: July 2026
What “blackout” means on a DP vessel
In DP language, a blackout is total loss of main electrical power to the main switchboard(s) — and therefore to thrusters, large consumers, and most ship systems. Without bus power there is no thruster force. The vessel becomes a drifting object under wind, wave, and current (see drift-off in the next section).
Blackout is not :
- loss of all position references only,
- failure of one gyro or wind sensor,
- navigation-light failure alone,
a single generator trip while another section still feeds thrusters (that is a partial power loss / section failure, serious but not full blackout).
- Event Power to thrusters? Typical DP result
- Full blackout No Drift-off until recovery
- One bus section black (open bus) Yes on healthy side Reduced capability; may hold if weather allows
- All PRS lost, power healthy Yes Model / remaining sensors; different emergency
- UPS-only computers, thrusters dead No main thruster power Control “alive,” vessel still drifts
Exam stems often mix these. If the stem says thrusters have no power and the main board is dead, answer blackout . If thrusters still run on the other ring, do not call it total blackout.
Why blackouts happen (exam-useful causes)
Blackouts arise from generation, distribution, or load problems — often combinations:
- generator overload / underfrequency cascade,
- short circuit with failed discrimination (especially closed common bus),
- simultaneous loss of online sets (fuel, cooling, control air, common auxiliaries),
- human error (wrong breaker, inhibited protection, manual trip),
- PMS / automation failure plus high demand,
industrial load step without reserve.
Understanding causes helps prevention (spinning reserve, open bus for critical work, healthy PMS). Recovery procedure, however, is largely cause-independent at the first minutes: get power and controlled thrust back .
UPS: what survives the blackout
Uninterruptible Power Supplies (UPS) feed DP process stations, operator stations, selected sensors (gyros, MRUs, some PRS receivers), and network gear for a limited duration. UPS purpose:
Keep the control brain alive so modes, alarms, and displays remain usable.
Avoid cold reboot of DP computers during a short power dip.
Support orderly recovery when main power returns.
UPS does not power full thruster motors for station-keeping. Believing “we still have DP because screens are on” while the main board is black is a fatal misconception. Screens on UPS with dead thrusters = drifting vessel with a working HMI .
Load Typically UPS-backed? Survives full blackout?
- DP computers / HMI Yes Yes (time-limited)
- Selected gyros / MRUs / PRS receivers Often yes Yes (time-limited)
- Thruster motors / VFDs full power No No
- Hotel loads No No
- Main generation N/A Offline until restarted
- Blackout recovery priorities
Vessel-specific blackout recovery procedures (engine room and bridge checklists) rule, but exam and industry logic share a priority order:
Recognise and raise the alarm — blackout declared; stop critical external work (diving, heavy lift, close approach) per ASOG/emergency plan.
Restore electrical generation — emergency/standby generators start; engineers clear faults; breakers closed to re-energise bus sections per procedure.
Restore thruster power carefully — feed thrusters only when voltage/frequency are stable and drives ready; do not slam full thruster demand into a fragile plant.
Re-establish controlled thruster use — manual thruster/joystick or controlled DP modes as procedure allows; check enables and power limits.
Re-enable PRS carefully — bring references online only when power and control are stable; avoid flooding a recovering controller with wild measurements.
Regain position / clear the hazard — move to a safe location if required; then rebuild Auto DP and footprint confidence.
Record and debrief — log times, actions, and plant state after the vessel is safe.
- Priority Action family Why first
- 1 Restore generation and main bus power No power → no thrust
- 2 Restart thrusters without surge Controlled force, plant protection
- 3 Re-enable PRS and full Auto DP carefully Bad references + high gain can drive-off
- 4 Resume task only if ASOG allows Critical work may remain aborted
Important
First priority is almost always re-establish electrical power so thrusters can restart. Re-entering a worksite track, finishing the logbook, or recalibrating references is not first while the board is dead.
Prevent thruster surge on recovery
A common secondary incident is thruster surge (or drive-off-like behaviour) when power returns: thrusters spin up hard because setpoints, gains, or residual force demands from before the blackout are still large, or because Auto DP is re-enabled with poor references. Prevention measures the exam expects you to reason about:
Confirm control mode before thrusters are enabled (often joystick/manual or thrusters zeroed per company SOP).
Check position/heading setpoints match present reality if entering Auto DP.
Bring PRS online gradually ; verify quality before high weighting.
Observe PMS load limits and spinning reserve; do not demand full weather capability on one weak genset.
Coordinate with engineers so frequency and voltage are healthy before large thruster ramps.
Watch for frozen or stale pre-blackout commands in some system designs — follow manufacturer recovery steps.
Operator procedures: bridge and engine room as one team
Blackout recovery is not a solo DPO software exercise. Typical operator responsibilities:
Immediately reduce operational risk (stop divers, clear ROV, inform OIM/client per emergency matrix).
Maintain situational awareness : drift direction, proximity to asset, depth of water, weather.
Use emergency communications and thruster/joystick control as soon as power allows if needed to clear a structure.
Follow the vessel blackout recovery checklist rather than inventing steps.
Do not fight the engineer for breaker control; agree who owns generation restoration.
After recovery, do not automatically resume critical DP work — reassess plant health, residual capability, and ASOG colour.
Worked recovery scenario
A closed-bus short blacks both sections of a PSV holding 30 m off a platform. Screens remain on UPS; thrusters stop; vessel begins drifting toward the jacket. The DPO sounds blackout, notifies the platform and master, and prepares joystick. Engineers start emergency generation and reclose breakers on one section first. When thrusters regain power, the DPO uses controlled joystick thrust to open distance from the platform before selecting Auto DP. PRS are re-enabled after power is stable; Auto DP is restored only with confirmed references and adequate online generation. The task remains aborted until the electrical fault is understood.
Exam traps for blackout items
- Trap Correct framing
- Blackout = all PRS failed Blackout is main power loss
- UPS keeps thrusters at full force UPS is for control/sensors , limited time
- First action: recalibrate laser First: restore power
- Immediately reselect Auto DP hard Recover carefully ; avoid thruster surge
- Resume diving as soon as screens return Screens ≠ thrusters; ASOG may stay red
Bottom line: blackout kills main power and thrusters; UPS only buys control continuity. Recover generation first, restore thrusters without surge, re-enable PRS carefully, and keep the worksite safe while the plant returns to a known healthy state.