Study guide

5.3 Radar/Microwave Relative References (RadaScan)

Nautical Institute DP Operator DPO

Track your progress as you read

Finished sections get a check mark.

1 Introduction & NI Scheme

1.1 Current Exam Facts 1.2 Phases A–E Pathway 1.3 Certificates, Eligibility & Revalidation

2 DP Principles Fundamentals

2.1 What is Dynamic Positioning & Degrees of Freedom 2.2 Seven Components of a DP System 2.3 The DP Operator & Human-Machine Interface

3 Controller, Model & Environmental Sensors

3.1 DP Controller & Mathematical Model 3.2 Kalman Filtering & Current Estimation 3.3 Gyrocompass & Heading Feedback 3.4 Wind Sensor, MRU & UPS

4 GNSS & Acoustic Position References

4.1 DGNSS & Differential Correction 4.2 Relative GNSS / RTK Concepts 4.3 Hydroacoustics USBL/SSBL 4.4 Long Baseline (LBL) Systems

5 Relative PRS, Selection & Voting

5.1 Light Taut Wire 5.2 Laser Relative References (Fanbeam/CyScan) 5.3 Radar/Microwave Relative References (RadaScan) 5.4 Reference Selection, Voting & Common-Mode Failure

6 Power Generation & PMS

6.1 Diesel-Electric Power Architecture 6.2 Power Management System 6.3 Load Sharing, Load Shedding & Spinning Reserve

7 Bus Configuration & Power Failures

7.1 Open vs Closed Bus-Tie 7.2 Blackout & Blackout Recovery 7.3 Drive-Off vs Drift-Off

8 Thrusters & Allocation

8.1 Tunnel, Azimuth & Retractable Thrusters 8.2 Thrust Allocation, Forbidden Zones & Bias 8.3 Thruster Interaction & Faulty Thruster Response

9 Control Modes

9.1 Auto DP Mode 9.2 Joystick & Independent Joystick System 9.3 Mode Selection & Practical Setup

10 DP Equipment Classes

10.1 IMO Equipment Classes 1, 2 and 3 10.2 MSC.1/Circ.1580 vs MSC/Circ.645 10.3 Sensor Redundancy & 2-out-of-3 Voting

11 FMEA, Worst Case Failure & Consequence Analysis

11.1 FMEA & Annual DP Trials 11.2 Worst Case Failure 11.3 Consequence Analysis

12 ASOG, CAM & TAM

12.1 Activity Specific Operating Guidelines (ASOG) 12.2 Critical Activity Mode (CAM) 12.3 Task Appropriate Mode (TAM)

13 Capability Plots & Approach Planning

13.1 DP Capability Plots 13.2 Footprint Plots & Weather-Optimal Heading 13.3 500 m Zone Approach & Escape Routes

14 Watchkeeping & Industry Guidance

14.1 Watchkeeping & Handover 14.2 Checklists, Alarms & Time to Terminate 14.3 IMCA M103/M117 Guidance Context

15 Integrated Operations & Assessment Strategy

15.1 Multi-System Failure Scenarios 15.2 Integrated Operations Case Studies 15.3 Induction Assessment Strategy

5.3 Radar/Microwave Relative References (RadaScan)

Key Takeaways Explain This Topic AI

RadaScan-type systems are microwave (radar) relative PRS that measure range and bearing to responders or dedicated targets on a structure

Microwave wavelengths generally perform better than laser in fog, rain, and spray that optically block Fanbeam/CyScan

Active responders/targets and correct identification remain essential; interference and multipath can still degrade quality

Like laser systems, radar relative PRS are relative to the structure—not absolute GNSS positions by themselves

Comparing taut wire, laser, and radar helps the DPO choose diversity: mechanical seabed, optical, and microwave principles

Last updated: July 2026

Microwave Relative References: Why They Exist

Laser relative systems are precise in clear air but fragile in bad optical weather. Offshore DP needed a relative structure-based reference that could keep working when fog banks, rain squalls, and thruster spray blank the laser. Radar/microwave relative position-reference systems — commonly examined under the product name RadaScan and similar microwave concepts — fill that niche.

Exam recognition phrase: microwave / radar energy / responders / better in fog and rain than laser / relative to structure .

Principle of Operation

A microwave relative PRS typically:

Emits radar/microwave energy from a vessel-mounted unit.

Communicates with or reflects from responders / dedicated targets mounted on the platform, rig, or other reference structure.

Measures range and bearing (and processes multi-target geometry where configured).

Outputs a continuous relative position to the DP controller with quality indicators.

  • Element Role
  • Microwave sensor head Transmits/receives radar energy; scans or tracks targets
  • Responders / active targets Mounted on structure; provide reliable returns at microwave frequencies
  • Processor Target ID, filtering, relative position solution
  • DP interface Feeds relative offsets into voting and the estimator

Active responders matter conceptually: the system is designed around cooperative targets, not random radar paint of the entire platform. Wrong target selection, dead batteries/power to a responder (where applicable), or mounting on a moving appendage creates the same class of operational errors seen with laser prisms — different physics, similar human-factor traps.

Better Poor-Visibility Performance Than Laser

The headline operational advantage over Fanbeam/CyScan:

  • Condition Laser relative Microwave relative (RadaScan-type)
  • Clear air Excellent Excellent / very good
  • Fog / mist Often poor Generally better
  • Heavy rain Often poor Generally better
  • Sea spray Often intermittent loss Generally more robust
  • Needs LOS to targets Yes (optical) Yes (radar path, but different attenuation)
  • Absolute WGS-84 alone? No No

This table is gold for exam stems that ask how RadaScan differs from Fanbeam/CyScan . The answer is almost always: microwave vs laser and better fog/rain/spray performance , not “measures depth,” not “uses seabed transponder arrays,” and not “provides satellite absolute position.”

Interference, Multipath, and Other Limits

Microwave is not magic immunity:

  • Issue Effect
  • Radio/radar interference Noise, dropouts, false tracks if environment is electromagnetically hostile
  • Multipath / complex steel clutter Reflections from adjacent structure can confuse geometry if not filtered
  • Target/responder failure Loss of that relative PRS channel
  • Geometry / range limits Too far, too close, or poor aspect angle reduces quality
  • Incorrect target ID Relative hold to wrong object
  • Structure motion Relative truth follows the structure (same as laser)

The DPO should still maintain independent absolute or alternative relative references so a microwave outage does not leave the vessel single-threaded. Weather that helps microwave relative systems (fog) may also stress visual lookout — procedures and watchkeeping still apply.

Relative Frame Reminder

RadaScan-type systems are relative PRS :

They answer “where am I relative to this structure’s responders?”

They do not replace DGNSS for open-water absolute station-keeping without a structure.

They do pair powerfully with DGNSS and HPR for principle diversity during platform work in dirty weather.

Comparison Table: Laser vs Radar vs Taut Wire

Use this master comparison for selection questions and oral/simulator explanations:

  • Feature Light taut wire Laser (Fanbeam/CyScan) Microwave (RadaScan-type)
  • Physical principle Mechanical wire + clump weight Optical laser to reflectors Radar/microwave to responders
  • Reference frame Relative to seabed weight Relative to structure targets Relative to structure targets
  • Needs structure targets? No Yes (prisms/reflectors) Yes (responders/targets)
  • Needs seabed weight? Yes No No
  • Best niche Shallow–moderate depth Close structure work, clear air Close structure work, poor optical weather
  • Classic weakness Depth, current, snag Fog, rain, glare, spray Interference, multipath, target issues
  • Deep water ideal? No Structure-dependent, not depth-based Structure-dependent, not depth-based
  • Absolute GNSS? No No No
  • Typical exam product names Light taut wire / LTW Fanbeam, CyScan RadaScan
  • How the Three Fit a Diverse Reference Mix

A robust platform-approach mix might look like:

DGNSS — absolute earth frame and long-range approach.

HPR/USBL or LBL — independent acoustic principle (where water depth and noise allow).

Laser and/or microwave relative — tight relative offsets to the structure; microwave preferred if weather is optical-hostile; laser excellent in clear conditions.

Taut wire — optional diversity in shallow fields if fitted and snag risk is acceptable.

You rarely need every sensor online at once, but you do need enough independent online references for Class 2/3 critical work, and you should not count two sensors that fail together as two principles.

Operator Practices for Microwave Relative PRS

Confirm responders/targets are powered, correctly identified, and mounted on the intended structure element.

Verify range/aspect is within system capability for the planned station-keeping box.

Prefer microwave relative when fog/rain/spray is forecast and laser is likely to drop — but still keep non-optical diversity (DGNSS/HPR).

Investigate interference sources if quality collapses without weather explanation (nearby radar, industrial RF, damaged cabling).

On voting rejection, do not force a noisy microwave channel back as “must have three greens” without quality — three healthy independents beat three forced labels.

Exam Scenarios

  • Scenario Correct link
  • RadaScan vs Fanbeam principal difference Microwave vs laser; better fog/rain/spray
  • Needs seabed transponder array False for RadaScan — that is HPR/LBL
  • Measures water depth under keel False — echo sounder, not relative radar PRS
  • Absolute satellite position False — relative structure reference
  • Platform work in thick fog with laser failing Microwave relative + other independents
  • Bottom Line for Assessment

RadaScan-type = microwave relative PRS to responders/targets .

Better than laser in many poor optical visibility conditions.

Still has interference, multipath, target limits.

Relative, not absolute .

Compare freely with taut wire and laser using principle, frame, and environment columns.