Study guide

11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies

Key Takeaways Explain This Topic AI

Level III task 3.4.1 requires preparing and reviewing technical reports, and Level IV 4.4.1 requires integrating Level II and III reports into a single deliverable.

A deficiency statement must give the location, the measurement, the comparison basis, the probable cause, the consequence, and a recommended action with urgency.

Trending detects degradation from the rate of change long before an absolute limit is reached, which is why baseline data is the most valuable record in a maintenance program.

Level II task 2.5.1 grades business communication, including the parts of a business letter and clear written communication with the client.

Reports must be written for two audiences at once: the technician who will perform the repair and the manager who will authorize it.

Last updated: August 2026

Technical Report Writing, Data Trending, and Communicating Deficiencies

Quick Answer: Reporting is graded at every level. Level II 2.4.4 requires preparing "simple reports on daily activities" and 2.5.1 requires maintaining business communications, with the knowledge listed as "parts of a business letter" and "proper sentence structure." Level III 3.4.1 requires " prepare and review technical reports." Level IV 4.4.1 requires " integrate Level II and III reports" into a coherent deliverable. The report is the product. Everything else is the process that produced it.

1. Why the report is the deliverable

A client does not buy test measurements. They buy a decision-quality answer to a question: is this equipment safe to energize, is it fit for another service interval, and what do I need to do about it. The measurements are the evidence; the report is the answer.

That framing has a practical consequence: a technically flawless test program that produces an unreadable, unactionable report has failed to deliver. Conversely, a clear report that surfaces the two findings that matter, in language a maintenance planner can act on, delivers most of the value.

2. Report structure

Section Content

Executive summary The conclusion, the count of deficiencies by severity, and the top recommendations — one page, readable by a manager

Scope What equipment was tested, to which standard, on what dates, by whom, under what authorization

Limitations and exclusions What was not tested, and why — access denied, outage window closed, component could not be isolated

  • Methodology Tests performed, standards applied, instruments used with serial numbers and calibration dates
  • Results Tabulated data by equipment, with conditions and corrections shown
  • Deficiencies Each finding, severity-ranked, with the elements in Section 3
  • Recommendations Prioritized, with urgency and, where possible, an owner
  • Appendices Raw data, thermograms, photographs, relay setting reports, curves, calibration certificates

The limitations section is the one candidates undervalue and the one that protects everybody. A report silent about an untested item implies it was tested and passed. If a failure later occurs there, the silence is indefensible. State plainly: "Cubicle 7 could not be tested; the tenant declined the outage. Recommend testing at the next available opportunity."

3. Writing a deficiency that gets acted on

A deficiency statement needs six elements. Omit any one and the finding will not be actioned correctly.

Location — specific enough for a crew to walk to it. "Switchgear SWG-2, cubicle 4, breaker load-side B-phase lug."

The measurement — what was found, with units and conditions.

The comparison basis — what it was measured against, named. "Referenced to A and C phases at identical load."

Probable cause — the technician's judgement. This is the element that distinguishes a report from a data dump.

Consequence — what happens if nothing is done, and on what timescale.

Recommended action with urgency — what to do, and when.

Compare:

Weak: "Hot spot found on SWG-2."

Strong: " SWG-2, cubicle 4, breaker load-side B-phase lug: 22 °C above A and C phases at identical load (450 A of 600 A rating), projected to approximately 39 °C at full load. Probable cause is a loose or corroded compression lug. Left uncorrected this will progress to thermal runaway and an open circuit or fire. Recommend de-energizing at the earliest opportunity, inspecting and cleaning the connection, re-torquing to the manufacturer's value, and re-surveying under load. Given the projected full-load rise this is a major discrepancy under NETA Table 100.18 and should not wait for the next scheduled outage."

The second version can be scheduled, resourced, and closed out. The first cannot.

Severity ranking must be consistent and explained. Whatever scheme is used — critical / major / minor, or a numbered priority — define it in the report so that "Priority 2" means the same thing to every reader.

4. Trending

Trending is what converts a test program from a compliance exercise into a predictive one. The absolute value tells you where you are; the rate of change tells you where you are going and how fast.

Worked example. A transformer winding's insulation resistance, all values corrected to 20 °C:

  • Year Corrected IR
  • Commissioning 5,000 MΩ
  • +3 years 4,200 MΩ
  • +6 years 3,100 MΩ
  • +9 years 1,800 MΩ

Every one of these comfortably exceeds any table minimum. Taken individually, each year's test is a pass. Taken as a trend, the winding has lost 64 % of its insulation resistance and the decline is accelerating — the losses per three-year interval are 800, 1,100, and 1,300 MΩ. That is a unit heading for trouble, and the finding is invisible to anyone comparing single readings against a limit.

Requirements for valid trending:

Consistent test conditions — same test voltage, same connections, same duration, same guard configuration. Change any of them and the comparison is broken.

Consistent correction — everything normalized to the same reference temperature.

Consistent instrument type where practical, with the instrument recorded.

A baseline. This is why acceptance testing has value long after commissioning: the ATS data set is the baseline. A maintenance program on equipment with no commissioning data is working blind for its first several cycles.

What to trend: insulation resistance, PI, power factor and capacitance, contact and bolted-connection resistance, winding resistance, DGA gas concentrations and rates of gas generation , oil quality parameters, battery cell impedance and voltage, thermographic ΔT at identical load, breaker timing and travel, and relay as-found deviation.

For DGA in particular, the rate of gas generation is more diagnostic than the concentration. A stable elevated level is a healed old event; a rapidly rising level at a lower absolute concentration is an active fault.

5. Writing for two audiences

Every report has two readers with different needs:

The technician or maintenance planner needs specificity, numbers, locations, torque values, and part identification.

The manager or owner needs the decision: what is the risk, what does it cost, when must it happen, what happens if we defer.

Serve both by putting the decision-quality summary at the front and the technical detail behind it. Do not make a manager read forty pages of tabulated micro-ohm readings to discover that one breaker should not be re-energized.

Language practices that matter:

Define acronyms on first use. DLRO, PI, TTR, VLF, GST, and MCOV are not universal vocabulary outside the trade.

State facts and judgements separately. "The measured value is 22 °C above the reference phases" is a fact. "Probable cause is a loose lug" is a judgement. Marking the difference is honest and it protects the technician if the judgement turns out wrong.

Avoid absolute claims the data does not support. "The equipment is safe" is a claim about the future. "The tests performed on the date shown produced results within the applicable criteria" is what the data actually supports.

Write in plain, direct sentences. Level II's outline literally grades "proper sentence structure" and the ability to "read and write standard English."

6. Integrating multi-crew reports at Level IV

Level IV's task is integration, and the difficulties are real:

Reconcile inconsistent formats and units across crews into one presentation.

Resolve contradictions. Two technicians reporting different values for the same connection must be reconciled before publication, not published side by side.

Identify patterns no single crew could see. Three crews each reporting one loose connection on a different lineup have collectively found a systemic torque or workmanship problem, and only the integrator sees it.

Normalize severity ranking so a "critical" from one crew means what a "critical" from another crew means.

Produce one coherent set of prioritized recommendations rather than three parallel lists.

That pattern-recognition step is where a Level IV report earns its value: converting a pile of individual findings into a statement about the condition of the installation.

Exam trap: A question asks whether a maintenance test that produced a value well above the NETA minimum needs to be reported as a concern, given a series of prior readings showing steady decline. The absolute value passing is not the whole answer — a consistent and accelerating downward trend is a reportable finding regardless of where the current reading sits relative to the table.