Study guide
1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR
NICET Electrical Power Testing Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)
1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR
2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements
2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes
3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids
3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing
4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers
4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices
5 Chapter 5: Power Cables, Busways, and Terminations
5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing
6 Chapter 6: Protective Relaying and Instrument Transformers
6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting
7 Chapter 7: Grounding Systems and Ground-Fault Protection
7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)
8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management
8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks
9 Chapter 9: Infrared Thermography and Condition-Based Assessment
9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques
10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis
10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations
11 Chapter 11: Documentation, Reporting, and Standards Literacy
11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA
12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice
12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance
1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR
Key Takeaways Explain This Topic AI
Class C designates fires involving energized electrical equipment; the letter identifies the energized hazard, not the burning material.
NICET Level I task 1.2a.1 requires correct selection and use of portable fire extinguishers, and 1.2a.3 requires application of first aid and CPR.
The PASS method - Pull, Aim at the base, Squeeze, Sweep - is the standard portable extinguisher technique, used only on incipient fires with a clear egress path.
Mineral transformer oil is a Class IIIB combustible liquid with a minimum 145 degrees C flash point; less-flammable fluids under NFPA 70 Article 450.23 have a fire point of at least 300 degrees C.
Electrical shock victims must not be touched until the source is de-energized or the victim is separated from it with a non-conductive means.
Last updated: August 2026
Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR
Quick Answer: Level I tasks 1.2a.1 (portable fire extinguishers) and 1.2a.3 (first aid and CPR) are graded separately, and Level II task 2.2a.1 adds fire hazard identification with OSHA 1910.106 and NFPA 30 . The rule that anchors the extinguisher questions: Class C is not a fuel class — it is an "energized electrical equipment" designation layered on top of whatever is actually burning.
1. Fire classification
- Class Burning material Typical agent
- A Ordinary combustibles — wood, paper, cloth, cable jacketing, trash Water, foam, ABC dry chemical
- B Flammable and combustible liquids and gases — transformer oil, solvents, cleaners CO₂, dry chemical, foam
- C Energized electrical equipment CO₂, dry chemical — non-conductive agents only
- D Combustible metals — magnesium, sodium, lithium, titanium Specialized dry powder
- K Cooking oils and fats Wet chemical
The critical concept: Class C describes a condition, not a fuel. A transformer fire is a Class B fire in Class C conditions while energized. De-energize it and the same fire is simply Class B. This is why a "BC" or "ABC" extinguisher is what appears at substation and switchgear locations — the C rating certifies that the agent will not conduct back to the operator.
Agent selection consequences:
CO₂ leaves no residue, which is why it is preferred around switchgear, relays, and control panels where dry chemical residue would be corrosive and require a full equipment cleaning. Its limitations are poor outdoor performance in wind, an asphyxiation hazard in confined spaces, and a cold-burn hazard from the horn.
ABC dry chemical (monoammonium phosphate) is versatile but the residue is mildly acidic and corrosive to electronics and copper. Using it on an energized relay panel converts a small fire into a full panel replacement.
Water and foam are never used on energized equipment. Both conduct.
Halon and clean-agent systems are used in fixed installations for exactly the reason CO₂ is used in portables: no residue.
2. Using a portable extinguisher: PASS, and when not to
P ull the pin. A im at the base of the fire — not the flame. S queeze the handle. S weep side to side.
Aiming at the flames rather than the base is the single most common practical error, and it appears as a distractor.
Equally examinable is when not to fight the fire . Portable extinguishers are for incipient-stage fires only. Evacuate and let the fire brigade respond if any of the following is true:
The fire is larger than a small waste container or is spreading.
You do not have a clear, unobstructed escape route at your back .
The room is filling with smoke.
You are not trained on the specific extinguisher, or you are unsure the agent is correct.
The extinguisher is discharged and the fire is not out.
Before use, verify the extinguisher is the correct type, fully charged (gauge in the green), inspected within the last month, and hydrostatically tested per its schedule. Level I lists "confirm that an extinguisher is of the appropriate type and properly certified for use" as a graded skill.
3. Flammable and combustible liquids — OSHA 1910.106 and NFPA 30
Level II task 2.2a.1 requires identifying fire hazards and storage and transportation requirements for flammable materials. The classification hinges on flash point — the lowest temperature at which a liquid gives off enough vapor to form an ignitable mixture.
- Category Flash point Examples in EPT work
- Flammable (Class I) Below 100 °F (37.8 °C) Contact cleaners, some solvents, aerosol propellants
- Combustible Class II 100-140 °F Some cleaning solvents
- Combustible Class IIIA 140-200 °F Certain oils
- Combustible Class IIIB At or above 200 °F Mineral transformer oil
Mineral insulating oil is a Class IIIB combustible liquid, with a minimum flash point of about 145 °C (roughly 293 °F) for new oil per ASTM specification. It is not "flammable" in the regulatory sense, but a large heated oil volume in a transformer fire behaves catastrophically, and a falling flash point in a service-aged oil is a fault indicator — it signals the presence of low-molecular-weight combustible gases produced by internal arcing.
Less-flammable liquids — silicone, high-molecular-weight hydrocarbon, and natural and synthetic esters — are defined by NFPA 70 Article 450.23 and IEEE C57.111 as having a fire point of at least 300 °C . That is the threshold that allows indoor installation without a vault under specified conditions, and it is a frequently examined number.
Practical requirements: bond and ground containers during liquid transfer to prevent static ignition, store flammables in approved cabinets, keep oil-soaked rags in self-closing metal containers, obtain a hot work permit before any cutting, welding, or grinding, and know the facility's burn-permit requirements — a skill Level I lists explicitly.
4. Arc flash and fire are different events
Candidates sometimes assume the extinguisher answers an arc flash question. It does not. An arc flash is an energy release event lasting milliseconds , not a sustained fire. There is no extinguisher response to an arc flash. The response is:
Do not approach until the circuit is confirmed de-energized.
Treat the victim for thermal burns and blast trauma.
Address any secondary fire the arc ignited — that is where the extinguisher belongs.
5. First aid and CPR — the electrical-specific elements
Level I task 1.2a.3 cites the American Red Cross First Aid and Safety Handbook and the American Heart Association Guidelines for CPR and ECC .
The rescuer's first rule: do not become the second victim.
Never touch a victim still in contact with an energized conductor. The victim is part of the circuit.
De-energize the source if that can be done immediately — open the breaker, pull the disconnect, operate the emergency stop.
If the source cannot be de-energized, separate the victim using a non-conductive means — a dry hot stick, a dry wooden implement, a rescue hook. Never a metal tool, never a wet or damp object, never bare hands.
Call for emergency response and retrieve the AED before beginning treatment where a second person is available.
Electrical injury has features other trauma does not:
Ventricular fibrillation is the common cause of death in low-voltage electrocution. Currents in the range of tens of milliamperes across the chest can induce it. This is why CPR plus early defibrillation is the treatment path and why AEDs are stocked at electrical work sites.
Entry and exit wounds at the skin can look minor while the current path has caused extensive deep tissue destruction, muscle necrosis, and kidney injury from myoglobin release. All electrical shock victims are transported for evaluation, regardless of how well they appear.
Delayed cardiac arrhythmia can occur hours after the event, which is another reason the victim does not simply return to work.
Arc flash burns are thermal. Do not remove clothing fused to the skin, do not apply ointments or ice, cover with a clean dry dressing, and treat for shock.
CPR essentials for an adult victim: check responsiveness and breathing, call for help and an AED, begin chest compressions at 100-120 per minute at a depth of at least 2 inches, allow full chest recoil, and minimize interruptions. Apply the AED as soon as it arrives and follow its prompts.
Exam trap: A question presents a small fire inside an energized 480 V motor control center and offers a water extinguisher, a foam extinguisher, a CO₂ extinguisher, and an ABC dry chemical extinguisher. Both CO₂ and ABC carry a C rating, but CO₂ is the graded answer for energized electronics because it leaves no corrosive residue on the controls and buswork.