Study guide

12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

Key Takeaways Explain This Topic AI

The NICET Code of Ethics has nine numbered obligations and is cited in Level I task 1.5.1, Level III task 3.5.3, and the Performance Measures at every level.

Item 1 requires notifying the employer, client, and other appropriate authority when a safety judgement is overruled, expressing the concern to the employer first.

Item 4 requires admitting errors and never distorting or altering facts to justify a decision.

NICET certification expires three years after it is awarded and every third year thereafter, and is maintained through Continuing Professional Development.

NICET Policy 28 prohibits using any seal or stamp conveying the NICET name, logo, or certification mark on technical documents or drawings.

Last updated: August 2026

NICET Code of Ethics, Client Relations, and Certification Maintenance

Quick Answer: Ethics is graded from the very bottom of the program. Level I task 1.5.1 requires the candidate to "communicate accurately and ethically about work," with the knowledge being " NICET Code of Ethics as it applies to reporting on work activities." Level III 3.5.3 requires applying "ethics to management of work processes and customer relations." The Performance Measures at every level require a supervisor to verify " ethical behavior on the job, consistent with the NICET Code of Ethics. "

1. The Code of Ethics

NICET's preamble states that certified technicians and technologists "recognize that the services they render have a significant impact on the quality of life for everyone," and that in performing their duties on behalf of "the public, employers, and clients, they shall demonstrate personal integrity and competence."

Accordingly, certificants shall:

Have due regard for the physical environment and for public safety, health, and well being. If their judgment is overruled under circumstances where the safety, health, property, or welfare of the public may be endangered, they shall notify their employer, client, and such other authority as may be appropriate . An employee shall initially express those concerns to the employer.

Undertake only those assignments for which they are competent by way of their education, training, and experience.

Perform their duties in an efficient and competent manner with fidelity and honesty.

Admit and accept their own errors when proven wrong and never distort nor alter the facts in an attempt to justify their decisions.

Avoid conflicts of interest whenever possible. When unavoidable, they shall disclose to their employer or client, in writing , any action that might create the appearance of a conflict of interest.

Avoid receiving and granting bribery in all its forms.

Strive to maintain their proficiency by updating their technical knowledge and skills in engineering technology.

Not misrepresent or permit misrepresentation of their own or their associate's academic or professional qualifications, nor exaggerate their degree of responsibility for any work.

Not reveal facts, data, or information obtained in connection with services rendered without prior consent of the client or employer, except as authorized by law.

Note the ordering in item 1. The obligation is not simply "report it to the authorities." The sequence is: raise it with the employer first , and then, if the concern is not addressed and public safety may be endangered, to the client and to such other authority as may be appropriate. Exam questions test this ordering, and answers that jump straight to an external authority without first raising it internally are incorrect.

2. Applying the Code to real situations

"Record the failed test as a pass so we can energize on schedule." Items 3 and 4 settle it: perform duties with fidelity and honesty, and never distort or alter the facts. Report the result accurately, state the recommendation, and document the client's instruction and decision in writing. The energization decision belongs to the owner; the accuracy of the record belongs to you.

"We don't have time for the ground resistance test — just put down last year's numbers." Fabricating data is a direct violation of items 3 and 4. Record the test as not performed , with the reason. A report silent about an untested item implies it was tested and passed.

"You're not qualified for this, but there's nobody else." Item 2 is unconditional: undertake only assignments for which you are competent. Schedule pressure is not an exception. The correct response is to say so and escalate.

Your own error is discovered after the report is delivered. Item 4 requires admitting and accepting it. Issue a corrected report promptly, notify everyone who received the original, and identify what the correction changes. Concealment converts an honest mistake into misconduct.

Your employer also sells the replacement equipment you are recommending. Item 5 — a real and common conflict in this industry. It is not automatically disqualifying, but it must be disclosed in writing . The recommendation must be technically justified on its own terms and traceable to the test data.

A vendor offers hospitality, tickets, or a gift while their equipment is being evaluated. Item 6, and the safe test is simple: would you be comfortable if the client knew? Follow the employer's gift policy and disclose.

A different client asks about problems you found at a competitor's site. Item 9 — client data is confidential and is not disclosed without consent, except as authorized by law. This includes test results, site conditions, and equipment problems. The general technical lesson can be shared; the client's identity and specifics cannot.

You are asked to sign a Performance Measure for a candidate who has not demonstrated the ability. Items 3 and 8. The verifier's initials are a representation that the candidate "has repeatedly demonstrated" that ability. Signing without that basis misrepresents a professional qualification and undermines the credential itself.

You are offered exam questions in advance, or asked to share them afterward. NICET's Conditions of Application address this explicitly: "acquiring and/or providing specific knowledge of test questions prior to testing, or acquiring or providing assistance during an examination; intentionally providing information to NICET that is incomplete, or inaccurate; or knowingly providing technical services in an unsafe, inaccurate, or unprofessional manner may subject the offender to any number of sanctions, including legal prosecution ." Every candidate signs a non-disclosure agreement before the exam begins, and declining to accept it results in a failed score with fees forfeited.

3. Sanctions

NICET "reserves the right to deny, suspend, or revoke any certification (pending or awarded)" where it determines that an applicant, candidate, or certificant has misrepresented information, violated a NICET policy or procedure, or violated the NICET Code of Ethics.

The credential is therefore contingent on conduct, not only on examination performance. That is what makes it worth something to a client.

4. Certification maintenance

All NICET certifications expire three years after an individual's initial certification is awarded, and every third year thereafter. Recertification is based on the certificant's activities during that three-year period, through Continuing Professional Development (CPD) .

Practical obligations:

Track CPD activity as it happens. Reconstructing three years of activity from memory in the final month is how lapses occur.

Understand what counts — technical training, relevant coursework, industry conference and seminar attendance, participation in code and standard development, professional society activity, and relevant instruction delivered.

Submit before the deadline. A lapsed certification is a materially worse position than a renewed one, and restoring it is harder than maintaining it.

Keep contact information current with NICET. The Conditions of Application make this the certificant's responsibility, and notices about renewal go to the address on file.

Item 7 of the Code frames CPD as an ethical obligation rather than an administrative chore: certificants shall "strive to maintain their proficiency by updating their technical knowledge and skills." A technician working to a superseded edition of a standard is not merely out of date; they are working outside the competence the credential asserts.

5. Using the credential correctly

NICET Policy 28 is specific and frequently violated in practice: "The use of any seal or stamp conveying the full NICET name, logo or certification mark on technical documents or drawings prepared, checked or reviewed by a NICET certificant is not authorized by NICET. "

Where a project requires a certificant to identify their credentials within a document or drawing, that information "must be contained within the title block of the document/drawing, or within a square or rectangular box near the title block."

And the point that item 8 makes unavoidable: NICET certification does not constitute a license to practice engineering. The Conditions of Application state it directly. A NICET certificant is a certified engineering technician or technologist . Representing the credential as engineering licensure, or performing work that requires a professional engineer's seal, misrepresents professional qualifications — a violation of item 8 and, in most jurisdictions, of state engineering practice law as well.

Represent the certification accurately: the correct program, the correct level, and the current status. "NICET Level II certified in Electrical Power Testing" is accurate; "NICET certified engineer" is not, on two counts.

6. Client relations

Level III's task pairs ethics with customer relations , and the connection is not decorative — the ethical obligations are what make a technician's report worth paying for.

Set accurate expectations. Explain what the testing will and will not determine. Testing establishes condition at a point in time; it does not guarantee future performance, and saying so protects both parties.

Communicate bad news early and directly. A client who learns about a failed test at the end of an outage has lost the opportunity to respond to it.

Explain findings in terms the client can act on — the risk, the consequence, the options, the cost of deferral.

Distinguish fact from judgement in every conversation, as in every report.

Do not oversell. Recommending unnecessary work damages the relationship permanently when it is discovered, and it is a conflict-of-interest problem under item 5 when your employer supplies the work.

Respect confidentiality under item 9, including in casual conversation. Discussing a client's problems at an industry event is a disclosure.

Exam trap: A question describes a technician whose safety judgement has been overruled by a supervisor in circumstances where the public may be endangered, and offers "immediately report the matter to the local authority having jurisdiction" as an option. Code item 1 requires notifying the employer, the client, and such other authority as appropriate — and it states specifically that an employee shall initially express those concerns to the employer. The internal step comes first.