Study guide

2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power

Key Takeaways Explain This Topic AI

Level II task 2.3.1 is entirely arithmetic: calculate voltage, current, and resistance in series and parallel circuits, and calculate power in a circuit.

Series resistances add directly; parallel conductances add, so parallel resistance is always smaller than the smallest branch.

In a series circuit current is common and voltages divide; in a parallel circuit voltage is common and currents divide.

Power dissipation follows P = VI = I squared R = V squared over R, and the I squared R form explains why a small connection resistance produces destructive heating at high current.

The 2026 Level I and Level II outlines both re-state this material as named tasks, so it is examined at every level of the program.

Last updated: August 2026

DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power

Quick Answer: NICET Level II domain 2.3 Troubleshooting and Analysis contains exactly one task — 2.3.1, "Calculate basic electrical quantities" — with the skills stated as "calculate voltage, current, and resistance in series and parallel circuits" and "calculate power (watts) in a circuit." The 2026 outlines re-state the same material at Level I ( 1.1.3 Describe basic electrical equations ) and Level II ( 2.4.1 Apply fundamental electrical laws to simple circuits ). This is guaranteed exam content and it is worth points that require no field experience at all.

1. Ohm's law and the three rearrangements V = I × R I = V R R = V I V = I \times R \qquad I = \frac{V}{R} \qquad R = \frac{V}{I} V = I × R I = R V ​ R = I V ​

Where V is in volts, I in amperes, and R in ohms. The single most common arithmetic error on level exams is a unit-prefix slip — mixing milliamperes with amperes, or megohms with ohms. Convert everything to base units before you compute.

  • Prefix Symbol Multiplier
  • micro µ 10⁻⁶
  • milli m 10⁻³
  • kilo k 10³
  • mega M 10⁶
  • giga G 10⁹

Worked example. A DLRO reports a breaker contact resistance of 45 µΩ. The breaker carries 1,200 A continuous. What is the voltage drop across the contacts? V = I × R = 1,200 × 45 × 10 − 6 = 0.054 V = 54 mV V = I \times R = 1{,}200 \times 45 \times 10^{-6} = 0.054\ \text{V} = 54\ \text{mV} V = I × R = 1 , 200 × 45 × 1 0 − 6 = 0.054 V = 54 mV

2. Kirchhoff's laws

Kirchhoff's Current Law (KCL): the algebraic sum of currents entering and leaving any node is zero. In a three-phase four-wire system the neutral carries the phasor sum of the three phase currents — which is why a balanced linear load produces near-zero neutral current, and why triplen harmonics from non-linear loads produce a neutral current that can exceed a phase current.

Kirchhoff's Voltage Law (KVL): the algebraic sum of voltage rises and drops around any closed loop is zero. This is the law behind every "the readings do not add up" troubleshooting question.

3. Series circuits

Elements in series share one current path .

  • Quantity Behaviour
  • Current Same through every element
  • Resistance R_T = R₁ + R₂ + R₃ + …
  • Voltage Divides in proportion to resistance; the drops sum to the source voltage
  • Voltage divider: V x = V S × R x R T V_x = V_S \times \frac{R_x}{R_T} V x ​ = V S ​ × R T ​ R x ​ ​

Worked example. A 125 V DC station battery feeds a trip circuit consisting of a 20 Ω trip coil in series with 5 Ω of cable resistance.

  • R_T = 20 + 5 = 25 Ω
  • I = 125 / 25 = 5.0 A
  • Voltage across the coil: V = 5.0 × 20 = 100 V

The coil only sees 100 V of the 125 V available. If cable resistance rises to 15 Ω through a corroded connection, current falls to 3.57 A and coil voltage falls to 71.4 V — potentially below the coil's minimum pickup, producing an intermittent failure to trip. This is the classic control-circuit troubleshooting scenario.

4. Parallel circuits

Elements in parallel share one pair of nodes .

  • Quantity Behaviour
  • Voltage Same across every branch
  • Resistance 1/R_T = 1/R₁ + 1/R₂ + 1/R₃ + …
  • Current Divides inversely with branch resistance; branch currents sum to total

For exactly two resistors the product-over-sum shortcut applies: R T = R 1 × R 2 R 1 + R 2 R_T = \frac{R_1 \times R_2}{R_1 + R_2} R T ​ = R 1 ​ + R 2 ​ R 1 ​ × R 2 ​ ​

For n equal resistors, R_T = R / n.

The rule that catches errors: total parallel resistance is always smaller than the smallest individual branch . If your arithmetic gives a larger number, you inverted something.

Worked example. Three parallel grounding electrodes measure 30 Ω, 25 Ω, and 20 Ω. 1 R T = 1 30 + 1 25 + 1 20 = 0.03333 + 0.04 + 0.05 = 0.12333 \frac{1}{R_T} = \frac{1}{30} + \frac{1}{25} + \frac{1}{20} = 0.03333 + 0.04 + 0.05 = 0.12333 R T ​ 1 ​ = 30 1 ​ + 25 1 ​ + 20 1 ​ = 0.03333 + 0.04 + 0.05 = 0.12333 R T = 8.11 Ω R_T = 8.11\ \Omega R T ​ = 8.11 Ω

Note this is a theoretical figure. Real electrodes suffer mutual resistance interference when spaced closer than roughly twice their driven depth, so the measured combined resistance is always higher than the parallel calculation predicts. Recognizing that gap is a Level III analysis skill.

5. Series-parallel reduction

Reduce from the inside out.

Worked example. A 48 V DC control supply feeds a 4 Ω series resistance, then splits into two parallel branches of 12 Ω and 6 Ω.

  • Parallel section: (12 × 6)/(12 + 6) = 72/18 = 4 Ω
  • Total: 4 + 4 = 8 Ω
  • Total current: 48 / 8 = 6 A
  • Drop across the series resistor: 6 × 4 = 24 V
  • Voltage across the parallel section: 48 - 24 = 24 V

Branch currents: 24/12 = 2 A and 24/6 = 4 A — which sum to 6 A, confirming the result.

Always run that final check. If branch currents do not sum to the total, the reduction is wrong.

6. Power P = V × I = I 2 R = V 2 R P = V \times I = I^2 R = \frac{V^2}{R} P = V × I = I 2 R = R V 2 ​

The I²R form is the one that matters in field testing , because it shows heating rises with the square of current.

Worked example. A bolted busway joint should measure 20 µΩ but measures 200 µΩ. The busway carries 2,000 A.

  • Good joint: P = I² R = 2,000² × 20 × 10⁻⁶ = 4,000,000 × 0.00002 = 80 W
  • Degraded joint: P = 4,000,000 × 0.0002 = 800 W

Eight hundred watts concentrated in a joint the size of a fist is a thermal runaway in progress: heat raises resistance, higher resistance produces more heat, and the joint eventually fails. That feedback loop is why contact resistance is trended rather than merely compared to a pass/fail limit , and why an infrared survey finds these joints before a DLRO campaign does.

7. Resistance, temperature, and conductor material

Metallic conductor resistance rises with temperature: R 2 = R 1 × T + t 2 T + t 1 R_2 = R_1 \times \frac{T + t_2}{T + t_1} R 2 ​ = R 1 ​ × T + t 1 ​ T + t 2 ​ ​

where T is 234.5 for copper and 228 for aluminum, and t₁ and t₂ are the initial and final temperatures in °C.

Note the direction and contrast it with insulation: conductor resistance increases with temperature, insulation resistance decreases with temperature. Candidates routinely apply the insulation correction factor in the conductor direction. The two behave oppositely because conduction in metal is impeded by lattice vibration while conduction in a dielectric is aided by thermal activation of charge carriers.

Exam trap: A question gives three parallel branches and offers an answer equal to the sum of the branch resistances. Parallel resistance can never exceed the smallest branch — that answer is checkable on sight without doing the arithmetic.