Study guide
6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies
NICET Electrical Power Testing Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)
1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR
2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements
2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes
3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids
3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing
4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers
4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices
5 Chapter 5: Power Cables, Busways, and Terminations
5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing
6 Chapter 6: Protective Relaying and Instrument Transformers
6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting
7 Chapter 7: Grounding Systems and Ground-Fault Protection
7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)
8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management
8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks
9 Chapter 9: Infrared Thermography and Condition-Based Assessment
9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques
10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis
10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations
11 Chapter 11: Documentation, Reporting, and Standards Literacy
11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA
12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice
12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance
6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies
Key Takeaways Explain This Topic AI
The 2026 Level III outline adds recognizing the essential components of short-circuit, protective device coordination, and arc flash studies as a named task.
A short-circuit study establishes available fault current, which sets equipment interrupting ratings and is an input to both coordination and arc flash calculations.
Coordination is achieved when the downstream device's total clearing curve stays below the upstream device's minimum operating curve across the fault current range.
IEEE 1584 computes incident energy from available fault current, arcing time, working distance, electrode configuration, and enclosure dimensions.
Lower fault current can produce higher incident energy because the protective device takes longer to clear, which is the central counterintuitive result of arc flash analysis.
Last updated: August 2026
Protective Device Coordination, Short-Circuit, and Arc Flash Studies
Quick Answer: The 2026 Level III outline adds task 3.6.2, "Recognize essential components of short-circuit, protective device coordination, and arc flash studies." The verb is recognize , not perform — the technician's role is to verify installed equipment against the study, feed the study accurate field data, and flag conditions that invalidate its assumptions . The three studies are sequential: the short-circuit study feeds coordination, and both feed the arc flash calculation.
1. The short-circuit study
What it produces: the available fault current at every bus and equipment location, in symmetrical rms amperes, together with X/R ratio and asymmetrical peak values.
What it needs as input:
Utility available fault contribution at the service point, obtained from the utility and stated with the source impedance.
Transformer data: kVA, primary and secondary voltage, and percent impedance — the single most influential number in the whole study. Percent impedance comes off the nameplate, which is why Level II grades nameplate data capture as a task.
Conductor data: size, material, length, and configuration, which add impedance and reduce fault current with distance.
Motor contribution: motors act as generators for the first few cycles of a fault and contribute meaningfully to the total.
What it is used for:
Verifying that every device's interrupting rating equals or exceeds the available fault current at its location . An under-rated device is a code violation and a life-safety hazard.
Verifying bus bracing against the mechanical forces of the asymmetrical peak.
Providing the fault current input to coordination and arc flash.
The technician's field role is verification: confirm the installed transformer's nameplate kVA and impedance match what the study assumed, confirm conductor sizes and lengths, confirm device frame sizes, trip units, rating plugs, and fuse classes match the study, and report any mismatch . A study built on a 5.75 % impedance transformer that was actually delivered at 4.5 % understates fault current everywhere downstream.
2. Coordination
The objective: for any fault, the device closest to the fault on the source side operates first, and nothing upstream operates. That confines the outage to the smallest possible section.
How it is read. Coordination is evaluated on a time-current curve (TCC) plot — log-log axes with all devices in a series path drawn on one sheet, all referred to a common voltage base.
The criterion: the downstream device's total clearing curve must lie below and to the left of the upstream device's minimum operating curve, with a margin, across the entire range of fault current the pair can see.
- Term Meaning
- Minimum melting (fuse) Earliest the element can begin to melt
- Total clearing (fuse) Latest the fuse fully clears including arcing time
Coordination time interval The margin between curves, covering breaker clearing time, relay overtravel, and tolerances
Selectivity The property of only the nearest device operating
Where coordination breaks down:
Curves cross. At some fault current the upstream device becomes faster than the downstream one, and a downstream fault trips the upstream device. Very common between an instantaneous element and a downstream device.
Instantaneous elements overlap. Two devices in series both with instantaneous elements covering the same current range cannot coordinate by time.
Zone selective interlocking (ZSI) is the engineered answer for the low-voltage case: the downstream trip unit sends a restraining signal upstream when it sees the fault, so the upstream device holds in for its full delay. Without the signal — meaning the fault is between the two — the upstream device trips with no delay. ZSI wiring is a functional test item : Level III task 3.1d.3 explicitly lists "perform functional testing of zone interlocking and control circuits."
Coordination versus protection is a real trade-off. Adding delay upstream improves selectivity but increases the arcing time for a fault at that location, which increases incident energy . That tension is the reason arc flash and coordination studies are performed together rather than independently.
3. Arc flash analysis under IEEE 1584
What IEEE 1584 computes: the incident energy at a defined working distance, in calories per square centimetre (cal/cm²), and the arc flash boundary — the distance at which incident energy falls to 1.2 cal/cm², the onset of a second-degree burn.
The inputs:
- Input Source
- Bolted fault current Short-circuit study
- Arcing current Derived from bolted fault current; always lower
- Arcing time From the protective device's TCC at the arcing current
- Working distance Typical distance from the arc to the worker's face and chest
- Gap between conductors Equipment class dependent
- Electrode configuration Vertical, horizontal, in-box, in-open-air — a 2018-edition refinement
- Enclosure dimensions Box size affects how energy is focused outward
- System voltage and grounding Affects arc sustainability
The counterintuitive result that anchors exam questions: lower available fault current can produce higher incident energy. The mechanism is arcing time. Incident energy is roughly proportional to arcing current multiplied by arcing time. If reducing the fault current drops the current below a protective device's instantaneous pickup, the device falls back onto its long inverse delay — clearing time can jump from a few cycles to several seconds. The current halved; the time went up thirtyfold; the energy went up.
Practical corollaries:
A location far down a long feeder can be worse than one close to the transformer.
Reduced-capacity operation — running on one transformer of a two-transformer bus, or on a backup generator with much lower fault contribution — can move a location into a higher PPE category. Studies therefore evaluate multiple system configurations , and labels may cite more than one.
Maintenance mode / energy-reducing settings — an "arc flash reduction maintenance system" that temporarily lowers the instantaneous setting while work is in progress — cuts arcing time and therefore incident energy. Verifying that this function operates is a legitimate field test.
Arc flash boundary versus shock boundaries is a distinction the exam probes: the arc flash boundary is calculated from thermal energy ; the limited, restricted, and prohibited-era shock approach boundaries are fixed table values based on voltage . They are different phenomena and the arc flash boundary can be either inside or outside the shock boundaries.
4. What the technician checks in the field
Labels exist, are legible, and are current. NFPA 70E requires equipment likely to be examined while energized to be field-marked with arc flash hazard information. A study updated without labels replaced is an incomplete job.
Study currency. Studies are reviewed at intervals — commonly not more than five years — and after any change to the electrical distribution system that could affect results.
Installed equipment matches the study. Frame sizes, trip units, rating plugs, sensor sizes, fuse class and rating, CT ratios, and relay settings.
As-left settings match the study. This is where testing intersects the study most directly: a technician who leaves a trip unit on a test setting or a "convenient" higher instantaneous invalidates both the coordination and the arc flash label.
Report configuration changes. New feeders, added transformers, changed utility service, and generator additions all change fault current.
Exam trap: A question offers "the arc flash boundary is determined from the system voltage using NFPA 70E Table 130.4" as an option. Shock approach boundaries come from voltage tables; the arc flash boundary is calculated from incident energy, and it is the distance at which exposure falls to 1.2 cal/cm².