Study guide

6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21)

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21)

Key Takeaways Explain This Topic AI

Differential protection (ANSI 87) operates on Kirchhoff's Current Law (sum of currents entering a node equals zero), providing high-speed, unit-zone protection that trips exclusively for faults inside the bounded CT zone without intentional time delay.

Transformer differential relays (87T) utilize percentage differential restraint characteristics with single or dual slope breakpoints, CT ratio tap matching, vector group phase shift compensation (e.g., 30° Delta-Wye compensation), zero-sequence filtering, and harmonic restraint (2nd harmonic for inrush, 5th harmonic for overexcitation).

Bus differential schemes (87B) employ high-impedance voltage-operated relays with stabilizing series resistors to remain secure during heavy external through-fault CT saturation, or advanced low-impedance numerical percentage differential algorithms.

Generator differential protection (87G) provides sensitive, high-speed phase-to-phase and phase-to-ground stator winding protection with pickup settings typically between 0.1 to 0.2 per-unit.

Distance / Impedance protection (ANSI 21) measures apparent impedance (Z = V / I) on transmission lines using Mho circle or Quadrilateral R-X characteristics arranged in stepped zones: Zone 1 (instantaneous, 80-85% reach), Zone 2 (overreaching, 120-130% reach, 15-30 cycles delay), and Zone 3 (reverse or remote backup, 150-200% reach).

Last updated: August 2026

Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21)

Quick Summary: Differential Protection (ANSI 87) and Distance/Impedance Protection (ANSI 21) represent the pinnacle of high-speed power system protection. Differential schemes provide absolute selectivity for transformers, buses, and generators by comparing currents entering and leaving the apparatus. Distance schemes protect transmission and sub-transmission lines by measuring apparent line impedance (Z = V / I) across stepped geographical reach zones.

Commissioning and testing these sophisticated protection elements requires an in-depth understanding of percentage restraint slope curves, harmonic blocking algorithms, vector phase angle compensation, and R-X impedance plane plotting per IEEE C37.91 , IEEE C37.113 , and NETA ATS Section 7.9 .

1. Principles of Differential Protection (ANSI 87)

Differential protection is a unit protection scheme based directly on Kirchhoff's Current Law (KCL) : the algebraic vector sum of all currents entering and leaving a healthy electrical node or piece of equipment must equal zero. ∑ I e n t e r i n g − ∑ I l e a v i n g = 0 \sum I_{entering} - \sum I_{leaving} = 0 ∑ I e n t er in g ​ − ∑ I l e a v in g ​ = 0 +-----------------------------------------------------------------------------------------+

  • | DIFFERENTIAL PROTECTION OPERATING PRINCIPLE |
  • | |
  • | EXTERNAL THROUGH-FAULT (Out-of-Zone): |
  • | Primary: ----( 1000 A -> )---- [ PROTECTED APPARATUS ] ----( 1000 A -> )---- [FAULT] |
  • | CTs: [ CT1 ] [ CT2 ] |
  • | Secondary: 5.0 A ------> ------> 5.0 A |
  • | | | |
  • | +-----------> [ 87 ] <-----------+ |
  • | Operating Current |
  • | I_op = |5.0 - 5.0| = 0 A (RESTRAIN / NO TRIP) |
  • | |
  • | INTERNAL FAULT (In-Zone): |
  • | Primary: ----( 1000 A -> )---- [ * FAULT * ] <----( 800 A <--- )------------------- |
  • | CTs: [ CT1 ] [ CT2 ] |
  • | Secondary: 5.0 A ------> <------ 4.0 A |
  • | | | |
  • | +-----------> [ 87 ] <-----------+ |
  • | Operating Current |
  • | I_op = |5.0 - (-4.0)| = 9.0 A (HIGH-SPEED TRIP) |
  • +-----------------------------------------------------------------------------------------+

The Percentage Differential Restraint Characteristic:

Under heavy external through-fault conditions, unequal CT saturation, CT ratio tolerances, and transformer tap changer positions create false spill current (differential current) in the operating winding. To prevent false tripping, percentage differential relays introduce a Restraint Quantity (I_rest) : Operating Current ( I o p ) = ∣ I 1 − I 2 ∣ \text{Operating Current } (I_{op}) = |I_1 - I_2| Operating Current ( I o p ​ ) = ∣ I 1 ​ − I 2 ​ ∣ Restraint Current ( I r e s t ) = ( ∣ I 1 ∣ + ∣ I 2 ∣ ) / 2 or max ⁡ ( ∣ I 1 ∣ , ∣ I 2 ∣ ) \text{Restraint Current } (I_{rest}) = (|I_1| + |I_2|) / 2 \quad \text{or} \quad \max(|I_1|, |I_2|) Restraint Current ( I res t ​ ) = ( ∣ I 1 ​ ∣ + ∣ I 2 ​ ∣ ) /2 or max ( ∣ I 1 ​ ∣ , ∣ I 2 ​ ∣ ) Tripping Criterion: I o p ≥ Slope × I r e s t + I p i c k u p _ m i n \text{Tripping Criterion:} \quad I_{op} \ge \text{Slope} \times I_{rest} + I_{pickup\_min} Tripping Criterion: I o p ​ ≥ Slope × I res t ​ + I p i c k u p _ min ​ Operating

  • Current (I_op)
  • ^
  • | / Dual-Slope (Slope 2: 50% - 80%)
  • | / (Heavy Through-Fault CT Saturation)
  • | Breakpoint /
  • | ----------+
  • | / Slope 1: 20% - 35%
  • | / (Normal Load & Small Tap Mismatch)
  • | +--------+
  • | TRIP REGION | I_min_pickup
  • | +----------------------------------------
  • | RESTRAIN (BLOCK) REGION
  • +-----------------------------------------------------------------> Restraint Current (I_rest)

Loading diagram... Transformer Differential (87T) Decision & Harmonic Restraint Architecture

2. Transformer Differential Protection (87T) Specifics

Protecting power transformers introduces complex physical phenomena that must be compensated within the differential algorithm:

1. Vector Group Phase Shift Compensation:

A Delta-Wye transformer (e.g., Dyn1 or Dyn11) introduces a 30° phase angle displacement between primary and secondary line currents.

Legacy Electromechanical Method: Compensated via physical CT wiring connections (CTs on the Wye winding were wired in Delta; CTs on the Delta winding were wired in Wye).

Modern Digital Relay Method: CTs on all windings are wired in standard Wye (Star) . The relay software performs internal mathematical matrix phase rotation (e.g., rotating current vectors by ±30°).

2. Zero-Sequence Current Filtering:

An external ground fault on the grounded-Wye side of a Delta-Wye transformer produces zero-sequence current (I0) that circulates in the Wye winding and returns through the neutral, but cannot pass through the Delta winding. Without zero-sequence filtering, this through-fault current appears as false differential current, causing an improper trip. Modern relays subtract zero-sequence current (IA - I0, IB - I0, IC - I0) mathematically.

3. Magnetizing Inrush and Harmonic Restraint:

When a transformer is energized, core magnetization drives the iron into deep unipolar saturation, drawing magnetizing inrush current reaching 8x to 12x full load current on one side only. Because inrush flows into the transformer without exiting, it appears as an internal fault.

2nd Harmonic Restraint / Blocking: Magnetizing inrush current is rich in 2nd harmonic current (120 Hz) . When the ratio of 2nd harmonic to fundamental current (I_2nd / I_fund) exceeds a preset threshold (typically 15% to 20% ), the relay automatically blocks differential tripping.

5th Harmonic Restraint / Blocking: Transformer core overexcitation (excessive Volts/Hertz caused by system overvoltage or underfrequency) produces severe 5th harmonic current (300 Hz) . Relays employ 5th harmonic blocking (typically set at 35% to 40% ) to prevent tripping during temporary system voltage surges, allowing V/Hz relays (ANSI 24) to handle sustained overexcitation.

3. Bus Differential (87B) and Generator Differential (87G)

Bus Differential Protection (ANSI 87B):

Substation buses connect multiple circuits with massive available short-circuit currents. An external fault on a single feeder can drive that feeder's CT into severe saturation while all other incoming CTs remain linear, creating enormous false spill current.

Bus Differential Scheme Operating Principle Advantages Requirements & Limitations

High-Impedance Voltage Differential (87B-HiZ) All CTs of identical ratio are paralleled into a high-impedance voltage relay in series with a stabilizing resistor (R_s). Immune to CT saturation on external through-faults; extremely fast (< 1 cycle); highly reliable. Requires dedicated, identical CT ratios on all breakers; all CTs must have fully distributed C-class cores; requires MOV surge voltage suppressors across relay.

Low-Impedance Numerical Bus Differential (87B-LoZ) Individual CT inputs from every breaker feed separate channels of a digital relay; numerical algorithms detect CT saturation. Accommodates mixed CT ratios; handles dynamic bus re-configuration (double bus / breaker-and-a-half); shares CTs with other relays. Requires complex multi-processor relay hardware; relies on software saturation detection algorithms.

High-Impedance Stabilizing Resistor Formula: V s t a b i l i z i n g = I f a u l t _ m a x _ s e c × ( R C T _ i n t e r n a l + R l e a d _ o n e _ w a y ) V_{stabilizing} = I_{fault\_max\_sec} \times (R_{CT\_internal} + R_{lead\_one\_way}) V s t abi l i z in g ​ = I f a u lt _ ma x _ sec ​ × ( R CT _ in t er na l ​ + R l e a d _ o n e _ w a y ​ ) R s t a b i l i z i n g = ( V s t a b i l i z i n g / I r e l a y _ p i c k u p ) − R r e l a y _ i n t e r n a l R_{stabilizing} = (V_{stabilizing} / I_{relay\_pickup}) - R_{relay\_internal} R s t abi l i z in g ​ = ( V s t abi l i z in g ​ / I re l a y _ p i c k u p ​ ) − R re l a y _ in t er na l ​

Generator Differential Protection (ANSI 87G):

Protects generator stator windings against phase-to-phase and phase-to-ground faults. Because generators do not experience inrush or phase shifts, 87G elements operate as sensitive, high-speed percentage differential relays with very low pickup settings (typically 0.10 to 0.20 per-unit ) and a single slope (typically 10% to 15% ).

4. Transmission Line Distance / Impedance Protection (ANSI 21)

Distance protection calculates the electrical impedance of the transmission line by comparing measured secondary voltage (V) to secondary current (I): Z m e a s u r e d = V s e c o n d a r y I s e c o n d a r y = V p r i m a r y / PTR I p r i m a r y / CTR = Z p r i m a r y × ( CTR PTR ) Z_{measured} = \frac{V_{secondary}}{I_{secondary}} = \frac{V_{primary} / \text{PTR}}{I_{primary} / \text{CTR}} = Z_{primary} \times \left(\frac{\text{CTR}}{\text{PTR}}\right) Z m e a s u re d ​ = I seco n d a ry ​ V seco n d a ry ​ ​ = I p r ima ry ​ / CTR V p r ima ry ​ / PTR ​ = Z p r ima ry ​ × ( PTR CTR ​ )

Because line impedance (Z = R + jX) is directly proportional to physical line length, the calculated impedance reflects the physical distance from the relay to the fault. +-----------------------------------------------------------------------------------------+

  • | STEPPED DISTANCE PROTECTION ZONES |
  • | |
  • | LOCAL SUBSTATION [A] REMOTE SUBSTATION [B] SUBSTATION [C] |
  • | ====== [ 52A ] =============================== [ 52B ] =============== [ 52C ] ===== |
  • | | | |
  • | |<------------ ZONE 1 (80% - 85%) -------->| |
  • | | [ 0 Cycles / Instantaneous Trip ] | |
  • | | | |
  • | |<---------------- ZONE 2 (120% - 130%) -------------->| |
  • | | [ 15 - 30 Cycles Time Delay (0.25 - 0.50 s) ] | |
  • | | | |
  • | |<----------------------- ZONE 3 (150% - 200%) -------------------------->| |
  • | | [ 45 - 90 Cycles Remote Backup Time Delay (0.75 - 1.50 s) ] | |
  • +-----------------------------------------------------------------------------------------+

Stepped Distance Zone Philosophy:

Zone 1 (Instantaneous Unit):

Set to reach 80% to 85% of the protected transmission line positive-sequence impedance (Z_1L).

Operates with zero intentional time delay (0 cycles).

Why not 100%? Prevents "overreaching" the remote substation bus due to CT/VT measurement errors, line impedance parameter inaccuracies, and DC offset transients.

Zone 2 (Overreaching Unit):

Set to reach 120% to 130% of the protected line impedance (covering the remaining 15-20% of the line plus 20-30% into the adjacent shortest line).

Operates with an intentional time delay of 15 to 30 cycles (0.25 to 0.50 seconds) to coordinate with Zone 1 relays at the remote terminal.

Zone 3 (Remote Backup / Reverse Unit):

Set to reach 150% to 200% of the protected line plus adjacent longest line impedance (or reverse reach behind the local bus).

Operates with a time delay of 45 to 90 cycles (0.75 to 1.50 seconds) to provide remote backup for bus or breaker failures at the remote station.

R-X Impedance Plane Characteristics: +-----------------------------------------------------------------------------------------+

  • | R-X DIAGRAM CHARACTERISTICS |
  • | |
  • | +X (Reactance) +X (Reactance) |
  • | ^ ^ |
  • | | / Line Angle (75°-85°) | / Line Angle |
  • | | +--+--+ | +-------+ X_reach |
  • | | / | \ | | | |
  • | | | | | MHO CIRCLE | | | QUADRILATERAL |
  • | | \ | / (Self-Polarized) | | | |
  • | | +--+--+ | +-------+ |
  • | ---------------+------+---------> +R ---------------+-------+---------> +R |
  • | | (Origin) (Resistance) | (Origin) R_reach (Fault Arc)|
  • | | | |
  • +-----------------------------------------------------------------------------------------+

Mho Characteristic: A circular operating boundary passing through the origin on the R-X diagram. Inherently directional; trips when measured impedance falls inside the circle.

Quadrilateral Characteristic: A 4-sided polygonal boundary with independently adjustable reach in resistance (R_reach) and reactance (X_reach). Superior for detecting high-resistance ground faults and arc resistance on short lines.

5. Secondary Injection Testing of 87 and 21 Elements

Testing Transformer Differential (87T) Elements:

Minimum Pickup Test: Inject single-phase current into primary winding channel (I1) with secondary channel (I2) at zero. Incrementally increase current until relay asserts 87T. Verify pickup matches I_min_pickup ± 3%.

Percentage Restraint Slope Verification:

Set up dual current injection (I1 and I2) out-of-phase by 180° to simulate through-current.

Establish fixed restraint levels (I_rest = 2 A, 5 A, 10 A).

Increase differential current until trip occurs; calculate measured slope: Slope = (I_op / I_rest) × 100%.

Verify Slope 1, Slope 2, and Breakpoint knee.

Harmonic Restraint Testing:

Inject fundamental 60 Hz current above pickup simultaneously with a variable 120 Hz (2nd harmonic) component.

Gradually increase 2nd harmonic content; record the percentage threshold where the 87T trip contact is blocked (verify setting: 15% ± 2%).

Repeat with 300 Hz (5th harmonic) component (verify setting: 35% ± 3%).

Testing Distance / Impedance (21) Elements:

MTA (Maximum Torque Angle / Line Characteristic Angle) Verification:

Inject test voltage (V) and current (I) at varying phase angles (e.g., from 0° to 90°).

Identify the angle of maximum sensitivity (typically 75° to 85° for transmission lines).

Reach Verification (Z_reach):

At the Maximum Torque Angle, hold current constant (e.g., 5.0 A) and slowly reduce voltage until the relay trips.

Calculate secondary reach: Z_reach = V_trip / I_test.

Verify Zone 1 reach (Z1), Zone 2 reach (Z2), and Zone 3 reach (Z3) against setting sheet tolerances (±3% to ±5% per NETA ATS Table 100.10).

Zone Timer Verification:

Apply a dynamic step-change in impedance from healthy nominal load (150% reach) to fault impedance (50% Zone 1 reach, 110% Zone 2 reach). Record instantaneous Zone 1 trip time (< 25 ms) and Zone 2 timer delay (0.30 s ± 15 ms).