Study guide

6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination

Key Takeaways Explain This Topic AI

Power system protection is architected around overlapping zones of protection bounded by current transformers and circuit breakers, guaranteeing zero unmonitored dead zones across electrical networks.

The five cardinal tenets of protection system design are selectivity (isolating only the faulted zone), speed (clearing faults before equipment damage or instability), sensitivity (detecting minimum fault levels), dependability (tripping when required), and security (avoiding false operations).

Standard ANSI/IEEE C37.2 device function numbers provide a universal industry language, including 50 (Instantaneous Overcurrent), 51 (Time Overcurrent), 52 (AC Circuit Breaker), 87 (Differential), 21 (Distance), 27/59 (Under/Overvoltage), 67 (Directional Overcurrent), 81U/O (Under/Over Frequency), and 86 (Lockout Relay).

Time-Current Characteristic (TCC) curves govern time-overcurrent (51) coordination, mathematically formulated via standardized IEEE and IEC inverse curve equations parameterized by Pickup Current (Tap × CTR) and Time Dial (TD) multipliers.

The Coordination Time Interval (CTI)—typically 0.20 to 0.40 seconds for electromechanical systems and 0.15 to 0.25 seconds for digital systems—guarantees selective tripping by budgeting for breaker clearing time, relay overtravel, CT errors, and safety margins.

Last updated: August 2026

Protective Relaying Fundamentals, Device ANSI Numbers, and Coordination

Quick Summary: Protective relaying systems monitor power system currents, voltages, and frequencies to detect abnormal faults and initiate high-speed circuit breaker tripping. Governed by ANSI/IEEE C37.2 , IEEE C37.90 , and NETA ATS/MTS , protection engineering balances five core objectives—selectivity, speed, sensitivity, dependability, and security—through precise device coordination and overlapping protection zones.

Protective relays do not prevent faults; rather, they detect short circuits, overloads, and abnormal operating conditions, isolating the faulted apparatus in the minimum possible time to minimize equipment damage, maintain system stability, and protect human life.

1. Core Protection Philosophy and Zones of Protection

A power system is segmented into distinct Zones of Protection , each encompassing a specific apparatus:

  • Generator Zones
  • Transformer Zones
  • Busbar Zones
  • Transmission / Distribution Feeder Zones
  • Motor Zones +-----------------------------------------------------------------------------------------+
  • | OVERLAPPING ZONES OF PROTECTION |
  • | |
  • | [ GENERATOR ZONE ] [ TRANSFORMER ZONE ] [ FEEDER ZONE ] |
  • | +-----------------------+ +------------------------+ +--------------------+ |
  • | | | | | | | |
  • | | (GEN) === [CT1] === | [52G] | === [CT2] === (XFMR) ==|== | [52F] === [CT3] ===| |
  • | | | | | | | |
  • | +-----------------------+ +------------------------+ +--------------------+ |
  • | ^ ^ ^ |
  • | |------- OVERLAP REGION --------| | |
  • | (Circuit Breaker 52G) | |
  • +-----------------------------------------------------------------------------------------+

The Overlap Principle:

To ensure that no part of the electrical system is left unprotected, adjacent protection zones must overlap . The boundary of each protection zone is defined by the physical location of the current transformers (CTs). By placing CTs on both sides of the circuit breaker (or utilizing bushing CTs on opposite sides of the breaker mechanism), the breaker itself resides within both zones, eliminating "blind spots."

Primary vs. Backup Protection:

Primary (Unit/Main) Protection: The first-line protection scheme designed to operate with no intentional time delay (or minimal coordination delay) to clear faults within its assigned zone.

Backup Protection: Operates with intentional time delay to clear faults if the primary scheme fails (due to relay failure, loss of DC trip supply, CT failure, or breaker mechanism failure).

Local Backup: Located within the same substation, utilizing separate relays, separate CT/VT inputs, and separate trip coils on the same breaker (or a breaker failure scheme, ANSI 50BF).

Remote Backup: Located at an adjacent upstream substation (e.g., an upstream overcurrent or Zone 2 distance relay), which trips all lines feeding the faulted bus, causing a larger system outage.

Loading diagram... Five Cardinal Tenets of Protective Relaying Design

2. Essential ANSI/IEEE C37.2 Standard Device Function Numbers

ANSI/IEEE C37.2 defines standardized numerical designations for electrical power apparatus protection and control functions:

ANSI Device Number Standard Function Name Operational Description & Protective Application

21 Distance / Impedance Relay Measures apparent impedance (Z = V / I); trips when measured impedance drops below reach setting (transmission lines).

25 Synchronizing / Synch-Check Relay Verifies voltage magnitude, phase angle difference (<10° to 20°), and slip frequency before permitting breaker closing between two systems.

27 Undervoltage Relay Operates when AC voltage drops below a preset threshold (bus undervoltage, motor protection, loss-of-source detection).

46 Reverse-Phase / Phase-Unbalance Relay Detects negative-sequence current (I2) caused by open phases, unbalanced loads, or phase reversal, protecting generators and motors from rotor overheating.

49 Thermal Overload Relay Protects transformers, cables, and motors against excessive temperature rise based on thermal replica models (I^2 × t).

50 Instantaneous Overcurrent Relay Operates with zero intentional time delay when current exceeds a predetermined threshold (high-magnitude short circuits).

51 AC Time Overcurrent Relay Operates with an inverse time characteristic ; trip time decreases as current magnitude increases (feeder overloads and coordinated faults).

51N / 51G Neutral / Ground Time Overcurrent Monitors residual neutral current (3I0) or zero-sequence ground sensor CT current for ground fault detection.

52 AC Circuit Breaker The primary switching and fault interruption apparatus (operated by 52a normally open and 52b normally closed auxiliary contacts).

59 Overvoltage Relay Operates when AC voltage exceeds a preset limit (generator load rejection, ferroresonance, capacitor overvoltage).

67 Directional Overcurrent Relay Operates only for overcurrent flowing in a specific predetermined direction, determined by phase angle comparison between current and reference voltage (polarizing quantity).

79 AC Reclosing Relay Automatically recloses a transmission or distribution feeder circuit breaker after an instantaneous trip to restore service following transient faults (lightning, tree contact).

81U / 81O Under / Over Frequency Relay Detects system generation-to-load imbalances; initiates high-speed underfrequency load shedding (UFLS) or generator overfrequency tripping.

86 Lockout Relay (Master Trip) High-speed, multi-contact auxiliary relay that trips and locks out all associated circuit breakers upon major faults (transformer differential, bus differential); requires manual or electrical deliberate reset before reclosing is permitted.

87 Differential Relay Operates on the difference between incoming and outgoing currents (Sum of I != 0) within a bounded zone (transformers, buses, generators, motors).

3. Time-Current Characteristic (TCC) Curves and Mathematical Formulations

Time overcurrent relays (ANSI 51) utilize standardized inverse Time-Current Characteristics (TCC). As fault current increases, the operating time decreases, ensuring fast clearing for severe close-in faults while coordinating with downstream devices for distant faults. Operating

  • Time (sec)
  • ^
  • 10 | \
  • | \
  • 1 | \ Moderately Inverse
  • | \---\ Very Inverse
  • 0.1 | \---\ Extremely Inverse
  • | \----
  • +-----------------------------------------> Multiples of Pickup Current (I / I_pickup)
  • 1x 2x 5x 10x 20x

IEEE Standard Curve Equation (IEEE C37.112): t ( I ) = T D × ( A ( I / I p i c k u p ) p − 1 + B ) t(I) = TD \times \left( \frac{A}{(I / I_{pickup})^p - 1} + B \right) t ( I ) = T D × ( ( I / I p i c k u p ​ ) p − 1 A ​ + B )

Where:

  • t(I) = Operating trip time in seconds
  • TD = Time Dial setting (multiplier from 0.5 to 15.0)
  • I = Measured secondary fault current
  • I_pickup = Selected pickup current setting (Tap × CTR)
  • A, B, p = Curve shape constants

IEEE Curve Type Constant A Constant B Exponent p Typical Protective Application

IEEE Moderately Inverse 0.0515 0.1140 0.02 Utility distribution feeders with long lines; gentle slope.

IEEE Very Inverse 19.61 0.4910 2.00 Feeders where fault current drops significantly with distance.

IEEE Extremely Inverse 28.20 0.1217 2.00 Transformer feeder protection, coordinating with upstream/downstream power fuses and cable damage curves (I^2 × t).

IEC 60255 Standard Curve Equation: t ( I ) = T M S × ( k ( I / I s ) α − 1 ) t(I) = TMS \times \left( \frac{k}{(I / I_s)^\alpha - 1} \right) t ( I ) = TMS × ( ( I / I s ​ ) α − 1 k ​ )

Where TMS is the Time Multiplier Setting, I_s is the current setpoint, and curve constants are defined as:

  • Standard Inverse: k = 0.14, α = 0.02
  • Very Inverse: k = 13.5, α = 1.00
  • Extremely Inverse: k = 80.0, α = 2.00
  • Long-Time Inverse: k = 120.0, α = 1.00

4. Relay Coordination and Coordination Time Interval (CTI)

Protective Device Coordination is the process of setting overcurrent devices in series such that the device closest to the fault trips first, isolating the minimum portion of the system. Total Upstream Operating Time = t d o w n s t r e a m + CTI \text{Total Upstream Operating Time} = t_{downstream} + \text{CTI} Total Upstream Operating Time = t d o w n s t re am ​ + CTI +-----------------------------------------------------------------------------------------+

  • | COORDINATION TIME INTERVAL (CTI) BUDGETING |
  • | |
  • | Upstream Relay Operating Time (0.55 s) |
  • | ==================================================== |
  • | ^ |
  • | | [SAFETY MARGIN] 0.10 s (Margin for setting drift / ambient) |
  • | | [CT RATIO & SATURATION ERROR] 0.05 s (CT transient performance error) |
  • | CTI | [RELAY OVERTRAVEL / OVERSHOOT] 0.10 s (Electromechanical disk coasting) |
  • | (0.35 s) | [BREAKER INTERRUPTING TIME] 0.08 s (5-Cycle breaker total clearing time) |
  • | v |
  • | ==================================================== |
  • | Downstream Relay Operating Time (0.20 s) |
  • +-----------------------------------------------------------------------------------------+

Breakdown of CTI Components:

Circuit Breaker Total Clearing Time (t_breaker): The time required from trip coil energization until the arc is fully extinguished in all phases. Typically 3 to 5 cycles (0.05 to 0.083 seconds) for modern medium-voltage vacuum or SF6 breakers.

Relay Overtravel / Overshoot (t_overtravel): In electromechanical relays, after the fault is cleared by the downstream breaker, the induction disc continues to rotate due to rotational inertia. An allowance of 0.10 seconds is required for electromechanical relays. For microprocessor relays, inertia is zero (t_overshoot ≤ 0.02 s).

CT Ratio and Transient Errors (t_error): Accounting for CT saturation delays and ratio inaccuracies during high asymmetrical faults (typically 0.05 seconds ).

Safety Margin (t_margin): Engineering safety factor to accommodate tolerance variations in relay calibration, temperature drift, and ambient variables (typically 0.10 seconds ).

Standard CTI Guidelines:

Electromechanical Upstream & Downstream: CTI = 0.30 to 0.40 seconds (typically 0.35 s).

Digital Upstream & Electromechanical Downstream: CTI = 0.20 to 0.30 seconds.

Digital Upstream & Digital Downstream: CTI = 0.15 to 0.25 seconds (typically 0.20 s).

Relay Coordinating with Downstream Fuse: Clear of the fuse total clearing curve by at least 0.15 to 0.20 seconds or 135% of fuse total clearing time.