Study guide

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans

Key Takeaways Explain This Topic AI

Level III task 3.3.1 requires using electrical drawings and site plans, and Level II 2.2b.2 requires reading one-line, riser, and other power distribution diagrams to perform equipment isolation.

IEEE 315 and ANSI Y32.9 define the graphic symbols, IEEE C37.2 the device function numbers, and NEMA ICS 19 the diagram conventions the outline references.

A one-line shows system topology with three phases collapsed into one path; a three-line shows each phase separately and is required for CT and PT connection detail.

A schematic shows control logic without regard to physical layout; a connection or wiring diagram shows actual terminal-by-terminal wiring.

The 2026 Level III outline adds verifying that electrical documents conform to nameplates and actual site conditions as a named task.

Last updated: August 2026

Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans

Quick Answer: Drawing literacy is graded at every level. Level II task 2.2b.2 requires knowledge of "symbols and layout of basic one-line, riser, or other power distribution diagrams," citing IEEE 315 , ANSI Y32.9 , NEMA ICS 19 , and NFPA 70B Annexes F and G . Level III 3.3.1 requires "use electrical drawings and site plans." The 2026 Level III outline adds 3.6.1, "Verify that electrical documents conform to nameplates and actual site conditions."

1. The four drawing types

Drawing Shows Does not show Used for

One-line (single-line) System topology with all three phases collapsed to one line Individual phase detail, control wiring Isolation planning, coordination, switching

Three-line Each phase drawn separately, with CT and PT connections and polarity Physical layout Relay and metering connection verification

Schematic (elementary) Control logic, drawn for readability of the sequence Physical wire routing or terminal numbers Understanding how a scheme operates

Connection / wiring diagram Actual terminal-by-terminal wiring Logic clarity Point-to-point checks, troubleshooting

One-line versus three-line is the distinction that matters most in practice. A one-line is a planning document — it tells you the sources, the paths, the devices, and what feeds what. It cannot tell you which CT secondary lead lands on which relay terminal, or which way the polarity dot faces. Any work involving instrument transformer connections, polarity, or phase relationships requires the three-line. A technician who tries to verify a differential relay's CT connections from a one-line is working from the wrong document.

Schematic versus connection diagram is the second key pair. A schematic is drawn so the logic reads clearly — contacts and coils are placed to make the sequence obvious, and a single device's contacts may appear scattered across the sheet wherever they function. A connection diagram is drawn so the wiring can be executed and traced — it shows terminal blocks, wire numbers, and actual physical grouping. You read the schematic to understand what the scheme does; you use the connection diagram to find the wire.

Site plans and riser diagrams locate equipment physically: where the substation sits, where the duct banks run, which floor a panel is on, how conductors rise through a building. Level III's task pairs "electrical drawings and site plans " because troubleshooting a feeder requires both what it connects and where it physically goes.

2. Symbols and conventions

IEEE 315 / ANSI Y32.9 define the graphic symbols. The essentials on a power one-line:

Transformers by winding configuration — delta (Δ) and wye (Y) , with the wye's neutral shown grounded, resistance-grounded, or floating.

Circuit breakers, drawn differently by class, versus disconnect switches (a simple break) versus fuses .

Current transformers and potential transformers, with polarity marks .

Relays shown as circles containing their device function numbers .

Motors, generators, capacitors, reactors, and surge arresters.

Grounding symbols distinguishing equipment ground, earth, and chassis.

IEEE C37.2 device function numbers turn a relay circle into a statement of function. The core set is covered in the protective relaying chapter; on a drawing, the number is often accompanied by a suffix that qualifies it — N for neutral, G for ground, T for transformer, B for bus, L for line. So 87T is transformer differential, 87B bus differential, 51N neutral time overcurrent.

NEMA ICS 19 covers diagram conventions for industrial control: the ladder-logic layout, the left and right power rails, and the rule that all contacts are shown in their de-energized, un-actuated state — a convention that catches candidates who read a normally-closed contact on a drawing and expect it to be closed in service when its coil is energized.

NFPA 70B Annexes F and G provide reference symbol and diagram material and are cited directly by the NICET outline.

3. Reading a one-line for isolation

This is the practical application Level II grades.

Start at the work location and trace upstream to every source. Follow every path, not the obvious one.

Identify every source that can backfeed: alternate feeders, bus ties, generators, UPS outputs, transfer switches, capacitor banks, and control power transformers — a CPT fed from the load side of the device you just opened will keep a control circuit live.

Note the normal position of every switching device — normally open ties are drawn open, but a tie that has been closed for maintenance changes the whole topology and the drawing will not know.

Identify the isolation points and confirm each provides a verifiable open.

Check for parallel paths — dual feeds, ring buses, and looped distribution mean opening one device does not isolate.

The transfer switch trap: an automatic transfer switch is a source. Work downstream of an ATS is not isolated by opening the normal source alone, because the ATS will detect the loss and transfer to the emergency source. Both sources must be isolated.

4. Reading a three-line for instrument transformers

The three-line is where polarity becomes visible, and polarity errors are the leading cause of differential and directional relay misoperation.

Polarity marks (dots or H1/X1 designations) show the instantaneous current direction relationship. Current entering the polarity mark on the primary produces current leaving the polarity mark on the secondary.

CT ratio and connection — wye or delta — must be read from the three-line, along with which taps are used on multi-ratio CTs.

The grounding point of a CT or PT secondary circuit must appear exactly once. Level III 3.1d.3 requires verifying "that current transformer secondary circuits are grounded and have only one grounding point." Two grounds create a parallel path that diverts current from the relay; zero grounds leave the circuit floating at an unsafe potential.

Phase rotation and phase labelling must be consistent across the drawing set.

5. Verifying drawings against the field

The 2026 outline makes this its own task, and it reflects reality: field drawings are frequently wrong. Equipment gets replaced with a different frame size, CT taps get changed, feeders get re-routed, and the drawing does not follow.

What to verify:

  • Item Check against
  • Transformer kVA, voltage, percent impedance , connection, cooling class Nameplate
  • CT and PT ratios and taps actually in use Nameplate and physical tap connection
  • Breaker frame size, trip unit type, rating plug / sensor Nameplate and physical inspection
  • Fuse type, class, rating The fuse itself
  • Relay model, firmware, settings in service The relay's own setting report
  • Conductor size, quantity, routing Field measurement
  • Device labelling and numbering Equipment nameplate versus drawing tag

A mismatch is a finding to report, not a puzzle to resolve on the spot. A CT installed on a different tap than the drawing shows changes relay pickup by that ratio; a transformer with a different percent impedance invalidates the short-circuit study; a breaker with a different rating plug invalidates the coordination study and the arc flash label. Each of those is an engineering matter, and the technician's job is to document precisely what is installed and escalate.

Red-lining — marking up the drawing set with as-found conditions — is the standard mechanism, and the marked set goes back with the report so the drawings can be formally revised.

6. Practical habits

Work from the current revision. Check the revision block and date. Testing against a superseded drawing produces confident, wrong results.

Highlight the circuit you are working on across the drawing set before starting, so every reference is to the same path.

Reconcile the one-line and the three-line. If they disagree, one is wrong and you need to know which before you connect anything.

Photograph nameplates. A photograph settles a later dispute about what was installed in a way that a transcribed number does not.

Exam trap: A question asks which drawing is required to verify the polarity and secondary connections of current transformers feeding a differential relay. A one-line collapses all three phases into a single path and cannot show individual CT connections or polarity marks — the three-line is required.