Study guide

3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation

Key Takeaways Explain This Topic AI

Dissolved Gas Analysis (DGA per ASTM D3612) is the most sensitive diagnostic tool for detecting incipient thermal and electrical faults in liquid-filled transformers.

Specific fault energy levels produce distinct diagnostic gases: Hydrogen (PD/corona), Ethylene (high-temp thermal >500°C), and Acetylene (high-energy arcing >800°C).

Cellulose degradation produces Carbon Monoxide (CO) and Carbon Dioxide (CO2); a CO2/CO ratio below 3 indicates severe localized paper overheating.

IEEE C57.104 (2019) evaluates transformer condition based on 90th/95th percentile cumulative gas limits (Status 1, 2, 3) and Gas Generation Rates (GGR).

Duval Triangle 1 uses relative percentages of Methane, Ethylene, and Acetylene to definitively classify faults into seven distinct zones (PD, T1, T2, T3, D1, D2, and DT).

Last updated: August 2026

Dissolved Gas Analysis (DGA), Duval Triangle, and Fault Interpretation

The Gold Standard of Transformer Diagnostics: Dissolved Gas Analysis (DGA) is universally recognized as the single most powerful diagnostic tool for identifying incipient internal faults in oil-immersed transformers. Electrical and thermal stresses break chemical bonds in mineral oil and paper insulation, generating specific combustible hydrocarbon gases whose composition and generation rate pinpoint the precise nature and severity of developing internal faults.

Physics and Chemistry of Gas Generation

Mineral insulating oil is a complex mixture of hydrocarbon molecules (paraffins, naphthenes, and aromatics: C_n H₂n+2 and C_n H₂n). When exposed to abnormal thermal or electrical energy, covalent carbon-hydrogen (C-H, bond energy ≈ 338 kJ/mol) and carbon-carbon (C-C, bond energy ≈ 607 kJ/mol) bonds undergo scission, creating free radical fragments that recombine into diagnostic gas molecules. THERMAL & ELECTRICAL ENERGY SPECTRUM

  • ENERGY: LOW ────────────────────────────────────────────────────────► EXTREME
  • TEMP: 150°C 300°C 500°C 700°C >1000°C
  • │ │ │ │ │
  • GAS: H2 (Hydrogen) CH4 (Methane) C2H6 (Ethane) C2H4 C2H2 (Acetylene)
  • Corona / PD Low-Temp Thermal Moderate Thermal (Ethylene) High-Energy Arc
  • Hot Oil (Plasma Arc)
  • Gas Formation Mechanisms

Key Diagnostic Gas Chemical Formula Predominant Fault Generation Mechanism

Hydrogen H₂ Low-energy electrical discharges, corona / partial discharge, electrolysis of moisture.

Methane CH₄ Low-temperature thermal oil breakdown (150°C – 300°C).

Ethane C₂H₆ Moderate-temperature thermal oil breakdown (200°C – 500°C).

Ethylene C₂H₄ High-temperature thermal oil breakdown (> 500°C); severe hotspot on core/windings.

Acetylene C₂H₂ High-energy electrical arcing (> 800°C – 1000°C) ; flashover, tap arcing.

Carbon Monoxide CO Thermal degradation of solid cellulose (paper, pressboard) insulation (> 105°C).

Carbon Dioxide CO₂ Normal aging oxidation and thermal degradation of cellulose insulation.

Cellulose Degradation and the CO₂ / CO Ratio

Kraft insulating paper consists of polymeric glucose rings ([C₆ H₁₀ O₅]_n). When paper overheats, it decomposes into carbon monoxide (CO), carbon dioxide (CO₂), moisture (H₂O), and furanic compounds.

Normal Paper Aging: Generates significantly more CO₂ than CO, yielding a CO₂ / CO ratio between 3.0 and 10.0 .

Active Paper Overheating (Thermal Fault): Rapid localized cellulose degradation produces excessive carbon monoxide, driving the CO₂ / CO ratio below 3.0 .

Low-Temperature Aging / Over-Oxidation: A CO₂ / CO ratio exceeding 10.0 indicates low-temperature thermal aging with high dissolved oxygen.

DGA Sampling Protocol (ASTM D3612)

Representative DGA results require strict adherence to ASTM D3612 :

Gas-Tight Glass Syringe: Use precision-ground, calibrated glass syringes (50 mL or 100 mL) fitted with a 3-way nylon stopcock.

Bubble-Free Sampling: Technicians must purge the sampling port thoroughly, flush the syringe multiple times, and ensure zero air bubbles or headspace exist in the collected syringe.

Protection from Sunlight: Samples in glass syringes must be shielded from sunlight/UV exposure during transit because photolysis reactions generate artificial hydrogen and hydrocarbon gases.

Laboratory Extraction: Diagnostic gases are extracted in the laboratory using vacuum extraction, headspace analysis, or stripper column gas chromatography.

IEEE C57.104 (2019) Condition Classification and Rates

The revised IEEE C57.104 (2019) standard evaluates transformer condition based on 90th and 95th percentile cumulative distribution limits (accounting for transformer age and breathing type) combined with the Gas Generation Rate (GGR) .

IEEE C57.104 Condition Status Levels +-----------------------------------------------------------------------------------------+

  • | IEEE C57.104 (2019) STATUS LEVELS |
  • | |
  • | • STATUS 1 (NORMAL): |
  • | - Gas concentrations below 90th percentile; low generation rate. |
  • | - Continue standard routine annual sampling. |
  • | |
  • | • STATUS 2 (PRECAUTIONARY): |
  • | - Gas levels between 90th and 95th percentile, OR elevated gas generation rate. |
  • | - Increase sampling frequency (e.g., quarterly/monthly); calculate rate-of-rise. |
  • | |
  • | • STATUS 3 (WARNING / CRITICAL): |
  • | - Gas levels exceed 95th percentile, OR high gas generation rate. |
  • | - Immediate engineering evaluation, load restriction, acoustic PD test, or outage. |
  • +-----------------------------------------------------------------------------------------+
  • 90th Percentile Gas Baseline Thresholds (Mineral Oil, Non-Breathing Sealed Tanks)

Diagnostic Gas 90th Percentile Limit (Status 1 / Status 2 Boundary) 95th Percentile Limit (Status 2 / Status 3 Boundary)

  • Hydrogen (H₂) 80 ppm 200 ppm
  • Methane (CH₄) 90 ppm 200 ppm
  • Ethane (C₂H₆) 90 ppm 175 ppm
  • Ethylene (C₂H₄) 50 ppm 100 ppm
  • Acetylene (C₂H₂) 1 ppm 2 ppm
  • Carbon Monoxide (CO) 900 ppm 1,400 ppm
  • Carbon Dioxide (CO₂) 9,000 ppm 14,000 ppm

The Acetylene Rule: Any detectable concentration of Acetylene (C₂H₂ > 1.0 ppm) represents an immediate red flag indicating electrical sparking or high-temperature arcing requiring immediate investigation.

Gas Generation Rate (GGR)

Evaluating active fault severity requires calculating the rate of combustible gas increase over time (Δppm / day): GGR = ( C f i n a l − C i n i t i a l ) / Δ t (days) \text{GGR} = (C_{final} - C_{initial}) / \Delta t\text{ (days)} GGR = ( C f ina l ​ − C ini t ia l ​ ) /Δ t (days)

Duval Triangle 1 Fault Diagnostic Method

Developed by Michel Duval, Duval Triangle 1 is the industry's most accurate graphical method for identifying transformer fault types. It utilizes three hydrocarbon gases with varying generation energies: Methane (CH₄) , Ethylene (C₂H₄) , and Acetylene (C₂H₂) .

Calculating Triangle Percentage Coordinates

Calculate total sum of the three triangular gases (T): T = [ C H 4 ] + [ C 2 H 4 ] + [ C 2 H 2 ] T = [CH_4] + [C_2 H_4] + [C_2 H_2] T = [ C H 4 ​ ] + [ C 2 ​ H 4 ​ ] + [ C 2 ​ H 2 ​ ]

Calculate triangular percentage coordinates: % C H 4 = ( [ C H 4 ] / T ) × 100 \%CH_4 = ([CH_4] / T) \times 100 % C H 4 ​ = ([ C H 4 ​ ] / T ) × 100 % C 2 H 4 = ( [ C 2 H 4 ] / T ) × 100 \%C_2 H_4 = ([C_2 H_4] / T) \times 100 % C 2 ​ H 4 ​ = ([ C 2 ​ H 4 ​ ] / T ) × 100 % C 2 H 2 = ( [ C 2 H 2 ] / T ) × 100 \%C_2 H_2 = ([C_2 H_2] / T) \times 100 % C 2 ​ H 2 ​ = ([ C 2 ​ H 2 ​ ] / T ) × 100 %CH4 (100%)

  • ▲
  • / \
  • / \
  • / PD \
  • / \
  • / T1 \
  • / \
  • / T2 D1 \
  • / \
  • / T3 DT \
  • / D2 \
  • (100%) %C2H4 ◄──-----------------------──► %C2H2 (100%)
  • Duval Triangle 1 Fault Classifications and Zone Boundaries
  • Fault Zone Fault Classification Physical Diagnosis / Root Cause Coordinate Boundaries
  • PD Partial Discharge Corona in gas-filled cavities, voids, or micro-bubbles in paper/oil. %CH₄ ≥ 98%

T1 Low-Temp Thermal Fault (T < 300°C) Localized overheating of conductors, core surface heating. %CH₄ > 76%, %C₂H₄ < 20%, %C₂H₂ < 4%

T2 Medium-Temp Thermal (300°C ≤ T ≤ 700°C) Overheating of internal copper connections, circulating core currents. 20% ≤ %C₂H₄ < 50%, %C₂H₂ < 4%

T3 High-Temp Thermal (T > 700°C) Large circulating currents in core/tank, severe joint overheating. %C₂H₄ ≥ 50%, %C₂H₂ < 15%

D1 Low-Energy Electrical Discharge Sparking, tracking in solid insulation, pinhole breakdown. %C₂H₂ > 13%, %C₂H₄ < 23%

D2 High-Energy Electrical Arcing Flashover, power arc between winding turns or to ground. %C₂H₂ ≥ 29%, %C₂H₄ ≥ 23%

DT Thermal and Electrical Mix Combined fault (e.g., thermal hotspot developing into arcing). Intermediate boundary region

Worked Example: Duval Triangle Calculation

A DGA laboratory report provides the following gas concentrations:

  • Methane (CH₄) = 150 ppm
  • Ethylene (C₂H₄) = 380 ppm
  • Acetylene (C₂H₂) = 12 ppm

Calculate triangular sum (T): T = 150 + 380 + 12 = 542 ppm T = 150 + 380 + 12 = 542\text{ ppm} T = 150 + 380 + 12 = 542 ppm

Calculate percentage coordinates: % C H 4 = ( 150 / 542 ) × 100 = 27.68 % \%CH_4 = (150 / 542) \times 100 = 27.68\% % C H 4 ​ = ( 150/542 ) × 100 = 27.68% % C 2 H 4 = ( 380 / 542 ) × 100 = 70.11 % \%C_2 H_4 = (380 / 542) \times 100 = 70.11\% % C 2 ​ H 4 ​ = ( 380/542 ) × 100 = 70.11% % C 2 H 2 = ( 12 / 542 ) × 100 = 2.21 % \%C_2 H_2 = (12 / 542) \times 100 = 2.21\% % C 2 ​ H 2 ​ = ( 12/542 ) × 100 = 2.21%

Evaluate zone: %C₂H₄ ≥ 50% (70.11%) and %C₂H₂ < 15% (2.21%), classifying this fault definitively as Zone T3: High-Temperature Thermal Fault (T > 700°C) .

Action Plans and Operational Response Protocols

When DGA indicates active gas generation or critical status thresholds:

Status 2 (Precautionary): Re-sample within 30 to 90 days to establish Gas Generation Rate (GGR). Perform infrared thermography on tank, radiators, and bushings. Review recent loading history.

Status 3 (Warning): Re-sample within 7 to 14 days. If GGR is confirmed positive and elevating, reduce transformer loading, perform Sweep Frequency Response Analysis (SFRA) and acoustic partial discharge location, and schedule an immediate diagnostic outage.

Loading diagram... DGA Fault Classification and Response Flowchart