Study guide

3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing

NICET Electrical Power Testing Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Electrical Safety, Standards, and Work Practices (NFPA 70E & OSHA)

1.1 NFPA 70E Framework, Electrically Safe Work Conditions, and Approach Boundaries 1.2 Arc Flash Hazard Analysis, Incident Energy, and PPE Category Selection 1.3 Hazardous Energy Control: OSHA 1910.147 Lockout/Tagout & Grounding Procedures 1.4 Confined Spaces, Hazard Communication, and Job Site Safety Management 1.5 Voltage Classes, Approach Boundaries in Practice, and Equipment Isolation 1.6 Temporary Protective Grounding: ASTM F855, OSHA 1910.269(n), and the Equipotential Zone 1.7 Fall Protection, Ladders, Scaffolds, and Elevated Work 1.8 Fire Hazards, Extinguisher Classes, Emergency Response, First Aid, and CPR

2 Chapter 2: Electrical Power Theory, Test Instrumentation, and Basic Measurements

2.1 AC/DC Power Fundamentals, Three-Phase Systems, and Power Factor Concepts 2.2 Insulation Resistance Testing Fundamentals, Megohmmeters, DAR, and PI (IEEE 43) 2.3 Low-Resistance Measurement: Contact Resistance, DLROs, and Micro-ohmmeters 2.4 High-Voltage Test Equipment: AC/DC Hipots, VLF Sets, and Dielectric Withstand Principles 2.5 DC Circuit Analysis: Ohm's Law, Series and Parallel Networks, and Power 2.6 Test Equipment Identification, Selection, Ranges, and Calibration Control 2.7 Insulation Power Factor and Dissipation Factor Instrumentation: GST, GSTg, and UST Modes

3 Chapter 3: Power Transformers, Regulators, and Insulating Fluids

3.1 Transformer Visual Inspection, Nameplate Interpretation, and Vector Groups 3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing 3.3 Insulation Power Factor & Dissipation Factor Testing (Doble Test & Bushings) 3.4 Insulating Liquid Testing: Dielectric Breakdown (ASTM D877/D1816) and Physical Properties 3.5 Dissolved Gas Analysis (DGA, ASTM D3612), Duval Triangle, and Fault Interpretation 3.6 Excitation Current, Core Insulation, and Applied and Induced Potential Tests 3.7 Load Tap Changers, Voltage Regulators, and Insulating Liquid Processing

4 Chapter 4: Circuit Breakers, Switchgear, and Motor Control Centers

4.1 Low-Voltage Circuit Breakers (MCCB/LVPCB) and Electronic Trip Unit Testing (LSIG) 4.2 Medium- and High-Voltage Circuit Breakers: Vacuum, SF6, and Air Magnetic Breakers 4.3 Circuit Breaker Timing, Motion/Travel Analysis, and Contact Velocity 4.4 Switchgear, Switchboards, MCC Buswork, and Interlock Systems 4.5 Overcurrent Device Testing: Primary Injection, Secondary Injection, and Time-Current Curves 4.6 Vacuum Interrupter Integrity Testing and SF₆ Gas Quality Management 4.7 Fuses, Medium-Voltage Switches, and Disconnecting Devices

5 Chapter 5: Power Cables, Busways, and Terminations

5.1 Medium-Voltage Cable Construction, Shielding, and Termination Inspection 5.2 Cable Insulation Resistance, DC Withstand, and VLF Field Testing (IEEE 400.2) 5.3 Advanced Cable Diagnostics: Tan-Delta / Dissipation Factor and Partial Discharge (IEEE 400.3) 5.4 Busways, Duct Banks, and Cable Shield Continuity Testing 5.5 Cable Fault Location: TDR, Thumping, Arc Reflection, and Sectionalizing

6 Chapter 6: Protective Relaying and Instrument Transformers

6.1 Current Transformers (CTs): Ratio, Polarity, Excitation/Saturation, and Burden Testing 6.2 Voltage Transformers (VTs/PTs) and Control Power Transformers (CPTs) 6.3 Protective Relaying Fundamentals, Device ANSI Numbers (50/51, 87, 21, 27/59, 81), and Coordination 6.4 Electromechanical, Solid-State, and Digital/Microprocessor Relay Testing Methods 6.5 Differential Protection (87T, 87B, 87G) and Impedance/Distance Protection (21) 6.6 Overcurrent Relay Testing (50/51): Pickup, Timing, Reset, and Curve Selection 6.7 Protective Device Coordination, Short-Circuit, and Arc Flash Studies 6.8 Watt-Hour Meters, Transducers, and Power Quality Analysis 6.9 SCADA, Substation Automation, Functional Test Plans, and P&C Troubleshooting

7 Chapter 7: Grounding Systems and Ground-Fault Protection

7.1 Ground Resistance Testing: Fall-of-Potential (IEEE 81), 62% Rule, and Clamp-On Methods 7.2 Soil Resistivity Measurement (Wenner 4-Pin Method) and Ground Grid Integrity 7.3 Equipment Grounding, System Grounding, and Bonding Verification 7.4 Ground-Fault Protection Systems (GFPE): Sensor, Relay, and Injection Testing (NEC 230.95) 7.5 Step and Touch Potential and Ground Grid Design Criteria (IEEE 80)

8 Chapter 8: Rotating Machinery, Specialty Equipment, and Commissioning Management

8.1 AC/DC Motors and Generators: Stator, Rotor, Surge Comparison, and High-Potential Testing 8.2 Stationary Battery Systems, UPS, and DC Distribution Testing (IEEE 450 / 1188) 8.3 Automatic Transfer Switches and Emergency Power Transfer 8.4 NETA Acceptance vs. Maintenance Standards, Test Data Trending, and Temperature Correction 8.5 Electrical Commissioning: The Phased Sequence from Receipt to Full Load 8.6 Surge Arresters: Types, MCOV, Application, and Field Evaluation 8.7 Capacitors, Reactors, and Harmonic Filter Banks

9 Chapter 9: Infrared Thermography and Condition-Based Assessment

9.1 Infrared Thermography Fundamentals: Emissivity, Reflectivity, and Camera Setup 9.2 Conducting and Evaluating Thermographic Surveys (NETA Section 9, Table 100.18) 9.3 Ultrasonic, Corona, and Vibration Survey Techniques

10 Chapter 10: Test Data Evaluation, Troubleshooting, and Failure Analysis

10.1 Reading Electrical Drawings: One-Lines, Three-Lines, Schematics, and Site Plans 10.2 Evaluating Test Results Against NETA, Manufacturer, and Baseline Data 10.3 Serviceability Determination and Energization Readiness 10.4 Failure Modes, Root-Cause Analysis, and Corrective Recommendations

11 Chapter 11: Documentation, Reporting, and Standards Literacy

11.1 IEEE C37.2 Device Function Numbers, IEEE 315 Symbols, and NEMA Ratings 11.2 Test Data Recording, Field Forms, and Data Integrity 11.3 Technical Report Writing, Data Trending, and Communicating Deficiencies 11.4 Standards and Regulatory Literacy: NETA, IEEE, NFPA, ASTM, ANSI, and OSHA

12 Chapter 12: Job Planning, Switching, Supervision, and Professional Practice

12.1 Site-Specific Safety Plans, Job Hazard Analysis, and Safety Audits 12.2 Project Testing (Job) Plans, Scheduling, and Resource Management 12.3 Switching Procedures: Development, Review, Confirmation, and Execution 12.4 Supervising Test Crews, Training, and Assigning Personnel 12.5 NICET Code of Ethics, Client Relations, and Certification Maintenance

3.2 Transformer Turns Ratio (TTR) and Winding Resistance Testing

Key Takeaways Explain This Topic AI

Transformer Turns Ratio (TTR) testing per IEEE C57.12.90 verifies winding turns counts and detects open turns, shorted turns, and tap changer misalignments.

NETA ATS/MTS acceptance criteria require that measured turns ratios deviate by no more than ±0.5% from calculated nameplate ratios across all DETC and LTC tap positions.

Winding DC resistance testing detects loose bolted joints, bad crimps, broken strands, and pitted tap changer contacts using 4-wire Kelvin micro-ohmmeter measurements.

Due to high winding inductance, technicians must allow full magnetic core saturation before recording readings and must never disconnect leads until test set discharge circuits dissipate inductive energy.

Winding resistance measurements must be temperature-corrected to 75°C (or 85°C) and must not deviate by more than 2% between adjacent phases (1% for factory baseline comparison).

Last updated: August 2026

Transformer Turns Ratio (TTR) and Winding Resistance Testing

Diagnostic Focus: Transformer Turns Ratio (TTR) and Winding DC Resistance testing are primary baseline electrical tests performed during commissioning and routine maintenance. TTR verifies the magnetic turns geometry and tap connections, while winding resistance verifies the physical integrity of current-carrying conductors, internal joints, and tap contacts.

Transformer Turns Ratio (TTR) Theory and Principles

Under ideal no-load conditions, the ratio of voltages induced in transformer windings is directly proportional to the physical ratio of turns in those windings: Turns Ratio = N p r i m a r y / N s e c o n d a r y = V p r i m a r y p h a s e / V s e c o n d a r y p h a s e \text{Turns Ratio} = N_{primary} / N_{secondary} = V_{primary\ phase} / V_{secondary\ phase} Turns Ratio = N p r ima ry ​ / N seco n d a ry ​ = V p r ima ry p ha se ​ / V seco n d a ry p ha se ​

Ratio Calculations for Three-Phase Winding Connections

Because nameplate voltages are stated as line-to-line (V_LL) values, calculating the theoretical phase turns ratio requires accounting for Delta (Δ) and Wye (Y) internal connections: DELTA (Δ) WINDING WYE (Y) WINDING

  • V_phase = V_line-to-line V_phase = V_line-to-line / √3
  • A A
  • / \ |
  • / \ |
  • / \ • Neutral
  • B-------C / \
  • / \
  • B C
  • Connection Configuration HV Phase Voltage (V_p,HV) LV Phase Voltage (V_p,LV) Theoretical Turns Ratio Formula
  • Delta – Delta (Dd) V_LL,HV V_LL,LV Ratio = V_LL,HV / V_LL,LV
  • Wye – Wye (Yy) V_LL,HV / √3 V_LL,LV / √3 Ratio = V_LL,HV / V_LL,LV
  • Delta – Wye (Dy) V_LL,HV V_LL,LV / √3 Ratio = √3 × (V_LL,HV / V_LL,LV)
  • Wye – Delta (Yd) V_LL,HV / √3 V_LL,LV Ratio = (1 / √3) × (V_LL,HV / V_LL,LV)
  • Worked Calculation: Delta-Wye Turns Ratio

A 13,800 V Delta to 480/277 V Wye distribution transformer is tested on its nominal tap: Theoretical Ratio = V p , H V / V p , L V = 13 , 800 V / ( 480 V / 3 ) = 13 , 800 V / 277.13 V = 49.796 \text{Theoretical Ratio} = V_{p,HV} / V_{p,LV} = 13,800\text{ V} / (480\text{ V} / \sqrt{3}) = 13,800\text{ V} / 277.13\text{ V} = 49.796 Theoretical Ratio = V p , H V ​ / V p , L V ​ = 13 , 800 V / ( 480 V / 3 ​ ) = 13 , 800 V /277.13 V = 49.796

TTR Test Procedure and Tap Sweep Protocol

TTR testing per IEEE C57.12.90 is executed by applying an AC excitation voltage (typically 8 V to 100 V AC, single-phase or three-phase) to the high-voltage winding while measuring the induced voltage and phase angle on the corresponding low-voltage winding. +-------------------------------------------------------------------------+

  • | TTR TEST EXECUTION RULES |
  • | 1. ALWAYS excite the HIGH-VOLTAGE winding to prevent dangerous step-up |
  • | voltages on the HV terminals. |
  • | 2. TEST ALL TAPS: Every DETC position (1-5) and all 33 LTC positions |
  • | (16 Raise through 16 Lower). |
  • | 3. RECORD ratio, excitation current, and phase angle deviation. |
  • +-------------------------------------------------------------------------+
  • Acceptance Criteria (NETA ATS/MTS Section 7.2.2)

According to NETA ATS Section 7.2.2.B.2 and NETA MTS Section 7.2.2.B.2 , measured turns ratio results must not deviate from the calculated nameplate ratio by more than ±0.5% : % Deviation = ∣ ( Measured Ratio − Calculated Ratio ) / Calculated Ratio ∣ × 100 % ≤ 0.50 % \%\text{ Deviation} = |(\text{Measured Ratio} - \text{Calculated Ratio}) / \text{Calculated Ratio}| \times 100\% \le 0.50\% % Deviation = ∣ ( Measured Ratio − Calculated Ratio ) / Calculated Ratio ∣ × 100% ≤ 0.50%

Failure Modes Identified by TTR

Turn-to-Turn Short Circuit: Causes a substantial change in measured ratio accompanied by abnormally high excitation current on the faulted phase winding.

Open Winding or Broken Tap Lead: Results in an open-circuit condition with zero induced secondary voltage (infinite ratio).

Misaligned Tap Mechanism: Generates ratios that do not match the designated tap step sequence or repeat previous tap ratios.

Reversed Winding Polarity / Internal Wiring Error: Results in a 180° phase angle error or incorrect phase displacement.

Winding DC Resistance Testing

Winding resistance testing measures the DC resistance of transformer coils to verify the health of current-carrying paths. It is extremely sensitive to mechanical defects, including loose bolted internal busbars, fractured conductor strands, poor crimps, and burnt, pitted, or misaligned LTC/DETC contacts.

4-Wire Kelvin Measurement Technique

To eliminate the resistance of test leads and contact probes, winding resistance is measured using a 4-wire (Kelvin) configuration: [ CONSTANT CURRENT SOURCE (I) ]

  • + -
  • | Current Lead (+) | Current Lead (-)
  • +--▼-------------------------▼--+
  • | C1 C2 |
  • | TRANSFORMER COIL |
  • | P1 P2 |
  • +--▲-------------------------▲--+
  • | Potential Lead (+) | Potential Lead (-)
  • + -
  • [ HIGH-IMPEDANCE VOLTMETER (V) ]
  • R_coil = V / I
  • Core Saturation Physics and Stabilization Time

Power transformer windings exhibit enormous inductance (L) coupled with very low resistance (R), creating a large magnetic time constant: τ = L / R \tau = L / R τ = L / R

When DC test current is initially injected, the current rises exponentially (I(t) = I₀(1 - e^-t/τ)). As the core iron becomes magnetically saturated, inductance drops dramatically and the test current stabilizes. Technicians must not record the resistance value until the digital reading has completely stabilized (which may require 30 seconds to several minutes on large power transformers).

Inductive Kickback Hazard: A transformer core stores substantial magnetic energy (E = 0.5 × L × I²). Sudden disconnection of DC leads while current is flowing produces a destructive inductive kickback voltage (V = -L × di/dt) that can exceed several thousand volts. Technicians must use test instruments equipped with automated discharge circuits and never disconnect test leads until the discharge sequence is complete and discharge indicator lamps confirm zero residual energy.

Temperature Correction of Winding Resistance

Copper and aluminum winding resistance varies directly with conductor temperature. All field measurements must be converted to a standard reference temperature (75°C for oil-filled units rated for 55°C or 65°C rise; 85°C or 100°C for dry-type units): R c o r r e c t e d = R m e a s u r e d × [ ( T k + T r e f e r e n c e ) / ( T k + T m e a s u r e d ) ] R_{corrected} = R_{measured} \times [(T_k + T_{reference}) / (T_k + T_{measured})] R correc t e d ​ = R m e a s u re d ​ × [( T k ​ + T re f ere n ce ​ ) / ( T k ​ + T m e a s u re d ​ )]

Where the inferred zero-resistance temperature constant (T_k) is:

T_k = 234.5°C for Copper (Cu) conductors.

T_k = 225.0°C (or 230.0°C) for Aluminum (Al) conductors.

Step-by-Step Worked Example: Temperature Correction

A copper winding on an oil-filled transformer is measured at a top oil temperature of 22.0°C with a measured resistance of 0.04520 Ω. Correct the reading to the 75.0°C standard baseline:

Identify constants: T k = 234.5 ∘ C , T r e f = 75.0 ∘ C , T m e a s = 22.0 ∘ C , R m e a s = 0.04520 Ω T_k = 234.5^\circ\text{C},\quad T_{ref} = 75.0^\circ\text{C},\quad T_{meas} = 22.0^\circ\text{C},\quad R_{meas} = 0.04520\ \Omega T k ​ = 234. 5 ∘ C , T re f ​ = 75. 0 ∘ C , T m e a s ​ = 22. 0 ∘ C , R m e a s ​ = 0.04520 Ω

Calculate temperature correction factor (F_T): F T = ( 234.5 + 75.0 ) / ( 234.5 + 22.0 ) = 309.5 / 256.5 = 1.20663 F_T = (234.5 + 75.0) / (234.5 + 22.0) = 309.5 / 256.5 = 1.20663 F T ​ = ( 234.5 + 75.0 ) / ( 234.5 + 22.0 ) = 309.5/256.5 = 1.20663

Calculate corrected resistance (R₇₅°C): R 75 ∘ C = 0.04520 Ω × 1.20663 = 0.05454 Ω ( 54.54 m Ω ) R_{75^\circ\text{C}} = 0.04520\ \Omega \times 1.20663 = 0.05454\ \Omega\ (54.54\text{ m}\Omega) R 7 5 ∘ C ​ = 0.04520 Ω × 1.20663 = 0.05454 Ω ( 54.54 m Ω )

Acceptance Criteria for Winding Resistance

According to NETA ATS / MTS Section 7.2.2.B.1 and IEEE C57.152 :

Phase-to-Phase Comparison: Temperature-corrected resistance values of adjacent winding phases (e.g., A-B vs. B-C vs. C-A on Delta, or A-N vs. B-N vs. C-N on Wye) must agree within 2.0% of each other.

Factory Baseline Comparison (NETA ATS): Field measurements must not deviate by more than 1.0% from factory test report values corrected to the same temperature.

LTC Tap Sweep Profiling: Resistance measurements across all 33 LTC tap steps must transition smoothly and monotonically without abrupt spikes or dropouts. A resistance spike on a specific tap indicates contact erosion, poor spring tension, or carbon buildup on that transition finger.

Loading diagram... Winding Resistance Testing and Inductive Discharge Safety Workflow