Study guide
6.4 Notification Appliance Circuit Loading
NICET Fire Alarm Systems Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: NICET FAS Levels, Exams, and Application Path
1.1 Program Purpose and Technician Role 1.2 Levels I Through IV and Role Expectations 1.3 Exam Counts, Times, Fees, and Format 1.4 Application, Work History, and Verification 1.5 Scheduling, Security, Scoring, and Retakes 1.6 Certification Maintenance and Study Planning
2 Code Navigation, References, and Exam Strategy
2.1 Reference Stack by Level 2.2 Physical and On-Screen Reference Rules 2.3 NFPA 72 Navigation Strategy 2.4 NFPA 70, Ugly's, and Electrical Reasoning 2.5 Building, Life Safety, and Management References 2.6 Timing, Exhibits, and Multi-Answer Strategy
3 Fire Alarm System Fundamentals and Components
3.1 System Architecture and Signal Flow 3.2 Control Units, Annunciators, and Interfaces 3.3 Initiating Devices and Detection Concepts 3.4 Notification Appliances and Occupant Signaling 3.5 Power Supplies, Circuits, and Supervision Basics 3.6 Basic Electricity, Electronics, and Field Vocabulary
4 Installation, Pathways, Devices, and Job-Site Safety
4.1 Work Plans, Drawings, and Field Conditions 4.2 Pathways, Raceways, and Cable Routing 4.3 Mounting Boxes and Peripheral Devices 4.4 Terminating Conductors and Labeling Circuits 4.5 Job-Site Safety for Fire Alarm Technicians 4.6 Commissioning Prep, Punch Lists, and Turnover Readiness
5 Inspection, Testing, Maintenance, and Impairments
5.1 Maintenance Domain Map for NICET FAS 5.2 Inspection, Testing, and Maintenance Distinctions 5.3 Periodic Testing Workflow 5.4 Deficiencies, Impairments, and Corrective Action 5.5 Documentation, Records, and Service History 5.6 Restoration, Troubleshooting, and Closeout
6 Power Supplies, Circuits, Loading, and Calculations
6.1 Power and Loading Domain Map for NICET FAS 6.2 Standby and Alarm Load Logic 6.3 Battery Sizing and Secondary Power 6.4 Notification Appliance Circuit Loading 6.5 Initiating and Signaling Circuit Supervision 6.6 Voltage Drop and Wire Resistance
7 Submittals, Technical Drawings, and System Layout
7.1 Drawing Package Purpose and Blueprint Fit 7.2 Site-Condition Surveys and Field Verification 7.3 Shop Drawing Content and Coordination 7.4 Layout Decisions for Devices, Pathways, and Interfaces 7.5 Drawing Review, Approval, and Level Responsibility 7.6 As-Builts, Closeout Packets, and Record Discipline
8 Commissioning, Acceptance, Troubleshooting, and Closeout
8.1 Commissioning Readiness and Systematic Startup 8.2 Acceptance Testing and Witness Coordination 8.3 Troubleshooting Faults and Deficiencies 8.4 Exam Exhibits, Scenario Logic, and Multi-Answer Items 8.5 Coordination with AHJ, Owner, Contractor, and Trades 8.6 Turnover, Closeout, and Post-Acceptance Support
9 Supervision, Project Coordination, and Work History
9.1 Level III and IV Supervision Boundaries 9.2 Coordinating Work Activities and Site Constraints 9.3 Leading Installation and Commissioning Teams 9.4 Managing Testing, Deficiencies, and Impairments 9.5 Documentation, As-Builts, Closeout, and Records 9.6 Work History, Verification, Recommendations, and Major Project Evidence
10 Complex Systems, Interfaces, and Specialty Operations
10.1 Level IV Complex Operations Frame 10.2 Suppression System Interfaces and Release Coordination 10.3 Networked Control Units and Distributed Systems 10.4 Smoke Control and High-Rise Interface Coordination 10.5 Air Sampling and Specialty Detection Strategy 10.6 Voice Evacuation, Emergency Radio, and Industry Coordination
11 Level-by-Level Review and Domain Remediation
11.1 Blueprint-First Review Method 11.2 Level I Remediation: Installation and Maintenance 11.3 Level II Remediation: Layout, Commissioning, and Coordination 11.4 Level III Remediation: Supervision, Records, and Approval 11.5 Level IV Remediation: Complex Operations and Leadership 11.6 Score Report Remediation and Practice Routing
12 Integrated NICET FAS Scenarios and Final Readiness
12.1 Integrated Scenario Reading Method 12.2 Final Seven-Day Study Plan 12.3 Exam-Day Reference and Logistics Checklist 12.4 Testing Interface, Timing, and NDA Readiness 12.5 Retake Decision Tree and Rescheduling 12.6 After Passing: Certification and Recertification
6.4 Notification Appliance Circuit Loading
Key Takeaways Explain This Topic AI
NAC loading checks the appliance current at its actual candela/setting against the circuit and the power-supply output ratings.
Passing the ampacity check does not guarantee passing voltage drop at the farthest appliance.
Strobe current rises with candela setting; always read the row for the model and cd shown in the exhibit.
Use only the appliances on the circuit/output under review — never borrow appliances from another NAC.
Last updated: June 2026
Notification Appliance Circuit Loading
A notification appliance circuit (NAC) powers audible and visible appliances — horns, strobes, horn/strobes, speakers — during alarm. NAC loading is a favorite NICET FAS scenario because it blends field recognition with arithmetic. You must know which appliances are on the circuit, the current each draws at its selected candela (cd) setting , what the circuit and the power-supply output can deliver, and whether wire resistance leaves enough voltage at the last appliance.
Strobe current is not a single number. It rises with candela: a published horn/strobe might draw roughly 0.090 A at 75 cd but 0.135 A at 110 cd and more at 177 cd. Current also varies by manufacturer, voltage range (regulated vs full-wave/filtered), and whether synchronization is used. The exam gives a current table when exact values matter; your job is to pick the correct row for the model and setting and multiply by quantity.
- Check What to use What it proves
- Appliance current Table row for model + cd setting Load per device
- Circuit current Sum of appliances on THAT NAC NAC rating not exceeded (e.g., 3.0 A)
- Supply output current Sum of all NACs on that output/supply Power supply not overloaded
- Voltage drop Current, wire resistance, distance End device gets usable voltage
- Spare capacity Rating minus load Whether additions are allowed
Worked loading example: NAC-2 carries 18 horn/strobes at 75 cd , each 0.090 A . Circuit current = 18 × 0.090 = 1.62 A . If the NAC is rated 3.0 A , the ampacity check passes (1.62 A < 3.0 A) with ~1.38 A spare. But that does not end the analysis — voltage drop at the far end must still be verified (Section 6.6).
Isolating the Circuit and the Common Traps
For NICET FAS scenarios, isolate the circuit first . If NAC-1 serves the first floor and NAC-2 serves the second floor, a question about adding three appliances to NAC-2 must not include NAC-1 appliances in the circuit-current sum. A question about total power-supply load, however, may include both outputs when one supply feeds both.
A NAC loading workflow:
Identify the circuit or supply output being tested.
Count only the appliances on that circuit/output.
Select current per appliance from the provided data at the actual cd setting.
Multiply current × quantity for each group.
Sum the group loads.
Compare the total to the NAC rating and the supply-output rating (two separate ratings).
If asked, calculate voltage drop at the farthest appliance.
Include synchronization/control-module loads if the scenario shows them.
Trap 1 — lowballing candela: using the lowest cd current because it makes the circuit pass. If the exhibit shows 110 cd, use the 110 cd current, not 15 cd. Trap 2 — supply vs circuit: checking only total power-supply capacity while ignoring the per-output rating. A supply may have ample total capacity while one output is overloaded. Trap 3 — unit mixing: combining 0.120 A with 120 mA as if they were different scales; convert first.
Voltage drop is a separate concern. A NAC can be well under its amp rating yet still deliver too little voltage at the farthest appliance because of conductor resistance and distance. If the question supplies wire size, distance, current, and a minimum operating voltage, expect voltage drop to be the deciding check.
NICET Level II places loading in the layout/submittal domain, so a drawing question may ask which NAC schedule is incomplete . A complete schedule shows device counts, models and cd settings, per-device current, the NAC and supply-output ratings, conductor size and length, and a voltage-drop basis. Missing any of these is a documentation gap a reviewer should flag.
Finally, watch the operating mode. Some appliances draw a different current in synchronized versus non-synchronized mode, and speaker NACs are sized by wattage tap (e.g., 1/4 W, 1/2 W, 1 W) rather than a fixed current. Use the data sheet value that matches the configuration in the exhibit.
Two Ratings, Two Failure Modes, and Spare Capacity
Every NAC has two limits you must satisfy, and they fail in different ways:
NAC circuit rating (e.g., 3.0 A) — the maximum current the single output can supply. Exceed it and the panel either will not power up the circuit or trips its internal protection.
Power-supply output rating — the total all NACs on that supply may draw. A supply with three 3.0 A NACs is rarely rated for 9.0 A total; the aggregate is its own limit.
A derating margin is also good practice: many designers load a NAC to no more than about 80% of its rating to leave headroom for tolerance and future devices. On a 3.0 A NAC that is 2.4 A; the 1.62 A worked load sits comfortably below it. The exam may ask for spare capacity — rating minus load — which here is 3.0 − 1.62 = 1.38 A , enough for roughly 15 more 75 cd strobes electrically, though voltage drop may limit additions sooner.
Reading the NAC Schedule on a Submittal
On a Level II layout/submittal question, you may be handed a NAC schedule and asked whether it is complete or which circuit is overloaded. A defensible schedule lists, per circuit: device count and models, candela/wattage settings, per-device alarm current, the circuit total , the NAC rating , the supply-output rating , conductor AWG and run length, and the end-of-line voltage (the voltage-drop result). Spotting the missing column is exactly the plan-review skill NICET tests.
A schedule that shows current but omits the voltage-drop basis, or shows wire size but no length, cannot be verified — and "insufficient information to verify" is sometimes the correct answer. Train yourself to check the output rating and the circuit rating as separate gates, because a supply can be fine in total while one of its outputs is over its individual limit.