Study guide
6.6 Voltage Drop and Wire Resistance
NICET Fire Alarm Systems Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation: NICET FAS Levels, Exams, and Application Path
1.1 Program Purpose and Technician Role 1.2 Levels I Through IV and Role Expectations 1.3 Exam Counts, Times, Fees, and Format 1.4 Application, Work History, and Verification 1.5 Scheduling, Security, Scoring, and Retakes 1.6 Certification Maintenance and Study Planning
2 Code Navigation, References, and Exam Strategy
2.1 Reference Stack by Level 2.2 Physical and On-Screen Reference Rules 2.3 NFPA 72 Navigation Strategy 2.4 NFPA 70, Ugly's, and Electrical Reasoning 2.5 Building, Life Safety, and Management References 2.6 Timing, Exhibits, and Multi-Answer Strategy
3 Fire Alarm System Fundamentals and Components
3.1 System Architecture and Signal Flow 3.2 Control Units, Annunciators, and Interfaces 3.3 Initiating Devices and Detection Concepts 3.4 Notification Appliances and Occupant Signaling 3.5 Power Supplies, Circuits, and Supervision Basics 3.6 Basic Electricity, Electronics, and Field Vocabulary
4 Installation, Pathways, Devices, and Job-Site Safety
4.1 Work Plans, Drawings, and Field Conditions 4.2 Pathways, Raceways, and Cable Routing 4.3 Mounting Boxes and Peripheral Devices 4.4 Terminating Conductors and Labeling Circuits 4.5 Job-Site Safety for Fire Alarm Technicians 4.6 Commissioning Prep, Punch Lists, and Turnover Readiness
5 Inspection, Testing, Maintenance, and Impairments
5.1 Maintenance Domain Map for NICET FAS 5.2 Inspection, Testing, and Maintenance Distinctions 5.3 Periodic Testing Workflow 5.4 Deficiencies, Impairments, and Corrective Action 5.5 Documentation, Records, and Service History 5.6 Restoration, Troubleshooting, and Closeout
6 Power Supplies, Circuits, Loading, and Calculations
6.1 Power and Loading Domain Map for NICET FAS 6.2 Standby and Alarm Load Logic 6.3 Battery Sizing and Secondary Power 6.4 Notification Appliance Circuit Loading 6.5 Initiating and Signaling Circuit Supervision 6.6 Voltage Drop and Wire Resistance
7 Submittals, Technical Drawings, and System Layout
7.1 Drawing Package Purpose and Blueprint Fit 7.2 Site-Condition Surveys and Field Verification 7.3 Shop Drawing Content and Coordination 7.4 Layout Decisions for Devices, Pathways, and Interfaces 7.5 Drawing Review, Approval, and Level Responsibility 7.6 As-Builts, Closeout Packets, and Record Discipline
8 Commissioning, Acceptance, Troubleshooting, and Closeout
8.1 Commissioning Readiness and Systematic Startup 8.2 Acceptance Testing and Witness Coordination 8.3 Troubleshooting Faults and Deficiencies 8.4 Exam Exhibits, Scenario Logic, and Multi-Answer Items 8.5 Coordination with AHJ, Owner, Contractor, and Trades 8.6 Turnover, Closeout, and Post-Acceptance Support
9 Supervision, Project Coordination, and Work History
9.1 Level III and IV Supervision Boundaries 9.2 Coordinating Work Activities and Site Constraints 9.3 Leading Installation and Commissioning Teams 9.4 Managing Testing, Deficiencies, and Impairments 9.5 Documentation, As-Builts, Closeout, and Records 9.6 Work History, Verification, Recommendations, and Major Project Evidence
10 Complex Systems, Interfaces, and Specialty Operations
10.1 Level IV Complex Operations Frame 10.2 Suppression System Interfaces and Release Coordination 10.3 Networked Control Units and Distributed Systems 10.4 Smoke Control and High-Rise Interface Coordination 10.5 Air Sampling and Specialty Detection Strategy 10.6 Voice Evacuation, Emergency Radio, and Industry Coordination
11 Level-by-Level Review and Domain Remediation
11.1 Blueprint-First Review Method 11.2 Level I Remediation: Installation and Maintenance 11.3 Level II Remediation: Layout, Commissioning, and Coordination 11.4 Level III Remediation: Supervision, Records, and Approval 11.5 Level IV Remediation: Complex Operations and Leadership 11.6 Score Report Remediation and Practice Routing
12 Integrated NICET FAS Scenarios and Final Readiness
12.1 Integrated Scenario Reading Method 12.2 Final Seven-Day Study Plan 12.3 Exam-Day Reference and Logistics Checklist 12.4 Testing Interface, Timing, and NDA Readiness 12.5 Retake Decision Tree and Rescheduling 12.6 After Passing: Certification and Recertification
6.6 Voltage Drop and Wire Resistance
Key Takeaways Explain This Topic AI
Voltage drop = current × total conductor resistance; the remaining voltage at the load is source minus drop.
Both the outgoing and return conductors carry current, so use twice the one-way length when the exhibit gives one-way distance.
Most notification appliances require at least about 16 V at the appliance; NAC calcs commonly start from a 20.4 V worst-case battery source.
Copper resistance: 14 AWG ≈ 3.14 Ω/1000 ft, 16 AWG ≈ 4.89 Ω/1000 ft, 18 AWG ≈ 7.95 Ω/1000 ft (round-trip doubles these).
Last updated: June 2026
Voltage Drop and Wire Resistance
Voltage drop is the loss of voltage caused by current flowing through conductor resistance. On a NAC, if the drop is too large the farthest horn/strobe may receive less than its listed minimum operating voltage — commonly about 16 V for 24 V-nominal appliances — and may fail to flash, sound at reduced volume, or behave erratically. Voltage drop most often appears with NACs, auxiliary power outputs, and long runs.
The governing relationship is Ohm's law applied to the conductors :
Voltage drop (V) = Circuit current (A) × Total conductor resistance (Ω)
Three details decide the answer:
Source voltage. Battery-powered NAC calcs typically start at a worst-case 20.4 V (the battery's discharged/end-of-life floor, ~15% below 24 V), not the nominal 24 V — this is the conservative value AHJs and designers use.
Round-trip length. Current flows out and back, so a circuit with a one-way run of L feet has 2L feet of conductor resistance. Forgetting the return path understates the drop by half.
Compare remaining voltage, not the drop. The pass/fail test is (source − drop) ≥ appliance minimum.
Standard solid-copper resistance values (per 1000 ft, one conductor):
- AWG Ω per 1000 ft Ω per ft
- 12 1.93 0.00193
- 14 3.14 0.00307
- 16 4.89 0.00489
- 18 7.95 0.00777
Read the exhibit's units before calculating: some give Ω/1000 ft, some give Ω/ft, some give total ohms. A unit slip here is a common, costly error.
Fully Worked Voltage-Drop Example
Scenario: A NAC carries 1.62 A of strobe load (from 6.4) to appliances at the end of a 500 ft (one-way) run of 14 AWG copper. Source = worst-case 20.4 V . Appliance minimum = 16 V . Does the end appliance receive enough voltage? (Simplified end-loaded model — all current to the far end.)
Voltage-drop worksheet
- Line Quantity Result
- A. Circuit current 1.62 A —
- B. One-way length 500 ft —
- C. Round-trip length (2 × B) 1000 ft —
- D. 14 AWG resistance 3.14 Ω/1000 ft —
- E. Total resistance (C × D / 1000) 1000 × 3.14 / 1000 3.14 Ω
- F. Voltage drop (A × E) 1.62 × 3.14 5.09 V
- G. Source voltage 20.4 V —
- H. Voltage at appliance (G − F) 20.4 − 5.09 15.31 V
- I. Required minimum 16 V —
- J. Pass/fail (H ≥ I?) 15.31 < 16 FAIL
Step-by-step:
Round-trip conductor length = 2 × 500 = 1000 ft .
Total resistance = 1000 ft × 3.14 Ω/1000 ft = 3.14 Ω .
Voltage drop = 1.62 A × 3.14 Ω = 5.09 V .
Voltage at the appliance = 20.4 − 5.09 = 15.31 V .
15.31 V is below the 16 V minimum → the circuit fails .
Design fixes (each reduces drop): increase wire size (12 AWG cuts resistance from 3.14 to 1.93 Ω/1000 ft → drop falls to about 3.13 V, giving ~17.27 V — a pass); shorten the run; split into two shorter NACs; relocate the panel/booster supply closer; or use lower-current LED appliances. Re-running with 12 AWG: total R = 1000 × 1.93/1000 = 1.93 Ω, drop = 1.62 × 1.93 = 3.13 V, end voltage = 20.4 − 3.13 = 17.27 V ≥ 16 V → PASS .
Trap 1 — answering with the drop: if the drop is 5.09 V, the appliance sees 15.31 V, not 5.09 V; compare the remaining voltage. Trap 2 — one-way length: using 500 ft instead of the 1000 ft round trip halves the drop and produces a false pass. Trap 3 — starting at 24 V: using nominal 24 V instead of the worst-case 20.4 V makes a marginal circuit look acceptable. Trap 4 — mixing units: treating 1.62 A as 1620 (mA) inside an amp equation.
Voltage drop interacts with NAC loading (6.4): a circuit can pass ampacity yet fail voltage drop, or vice versa. The correct exam answer checks the condition the stem actually asks. A plan that shows NAC counts and wire size but no current or voltage-drop basis has a documentation gap a reviewer should flag.
Why 20.4 V, and the Segment-Current Refinement
The 20.4 V starting point deserves a sentence of why : a 24 V-nominal system rides on a battery, and a discharged lead-acid battery near the end of its standby duty can sag to roughly 85% of 24 V , i.e., about 20.4 V. Designing from 20.4 V guarantees the appliance still gets ≥16 V even on the worst day of a power outage. Using the cheerful nominal 24 V hides exactly the condition the calculation is meant to protect against, which is why it is a deliberate trap value in answer choices.
The end-loaded model used in the worked example (all current at the far end) is the conservative case and is what most exam problems use. Real circuits with appliances spread along the run carry less current in the later segments, so a segment-by-segment analysis yields a smaller drop. If an exhibit explicitly gives device positions and per-segment currents, sum the drop segment by segment: each segment's drop = (current in that segment) × (segment round-trip resistance), and the total drop to the last device is the sum.
If the exhibit gives only a total current and total length, the end-loaded model is expected. Choosing the wrong model is a subtle trap; when in doubt, the conservative end-loaded result will never under -state the drop.
A Reusable Voltage-Drop Checklist
Identify the critical (farthest) appliance.
Determine the current in the conductor path to it.
Pull resistance from the table in the correct units (Ω/ft vs Ω/1000 ft).
Use the round-trip length (2 × one-way).
Compute drop = current × total resistance.
Subtract from the worst-case source (20.4 V for battery NACs).
Compare the remaining voltage to the appliance minimum (~16 V).
If it fails, upsize wire, shorten/split the run, relocate the supply, or use lower-current LED appliances.
Because personal calculators are barred, write each labeled value — amps, ohms, feet, volts — and keep the arithmetic linear. If answer choices are close, rounding matters; if they differ by 2× or 1000×, suspect a forgotten return path or a milliamp/amp slip rather than a rounding issue.