Study guide

3.3 Survey Stakes, Cut/Fill Notation, Differential Leveling (HI Method) & Percent Slope

NICET Highway Construction Inspection Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & the Inspector's Role

NICET HCI Certification: Levels I–IV, Exam Format & the 2026 Open-Reference Change The Inspector's Role, Authority, Ethics & Communication

2 Plans, Specifications & Contract Documents

2.1 Reading Plans & Drawings; Standard Construction Terminology 2.2 Plans vs. Specifications & Order of Precedence (FP-24, Special Provisions, Standard/Supplemental Specifications) 2.3 Contract Administration: Change Orders, Force Account & Project Documents

3 Measurement, Survey & Site Layout

3.1 Units, Conversions & Inspection Math 3.2 Stationing, Offsets & Locating Work from the Plans 3.3 Survey Stakes, Cut/Fill Notation, Differential Leveling (HI Method) & Percent Slope

4 Soils, Aggregates & Earthwork

4.1 Soil & Aggregate Types, Classification & Properties 4.2 Sieve Analysis & Gradation (AASHTO T27 / T11) 4.3 Moisture-Density Relationship: Proctor (AASHTO T99 / T180) 4.4 Field Density & Percent Compaction (Nuclear Gauge T310, Sand Cone T191) 4.5 Embankment & Subgrade Construction: Lifts, Proof Rolling & Earthwork Quantities 4.6 Slope Stabilization, MSE Walls & Geosynthetics

5 Portland Cement Concrete

5.1 Concrete Materials, Mix Design, Certification & Acceptance 5.2 Sampling Fresh Concrete & Slump (ASTM C143 / AASHTO T119) 5.3 Air Content, Unit Weight & Yield (C231/T152, C138/T121) 5.4 Cylinders (C31), Compressive Strength (C39/T22) & Temperature 5.5 Placement, Consolidation, Finishing, Curing & Concrete-Pavement Joints/Sawing

6 Asphalt / HMA Pavement

HMA Materials, Mix Types, Surface Prep & Tack/Prime Coats Sampling & Maximum Specific Gravity (Rice, AASHTO T209); Density Acceptance Placement, Rolling Sequence, Compaction & Yield

7 Reinforcement, Formwork & Structures

Reinforcing Steel: Grades, Cover, Placement, Splices & Pay Weight Formwork & Falsework Inspection Foundations: Footings, Driven Piles & Drilled Shafts Structural Steel, Connections & Prestressed/Post-Tensioned/Precast Concrete Bridge Decks, Mass Concrete & Protective Coatings

8 Drainage, Utilities & Incidentals

8.1 Drainage Systems: Pipe, Bedding, Backfill, Grade & Slope 8.2 Erosion, Sediment Control & Storm Water Management 8.3 Curbs, Sidewalks, Curb Ramps (ADA), Guardrail, Utilities, Signals & Lighting

9 Work-Zone Safety & Traffic Control

Personal Safety, PPE & Hazard Recognition OSHA Excavation & Trenching Safety (5-Ft Rule, Competent Person, Protective Systems) MUTCD Temporary Traffic Control: the Four Areas of a TTC Zone

10 Documentation, Materials Acceptance & Administration

10.1 Project Documentation, Daily Reports, Pay Quantities & Non-Conformance Reporting 10.2 Schedules, Budgets, Payment & Project Closeout (Level IV Administration)

3.3 Survey Stakes, Cut/Fill Notation, Differential Leveling (HI Method) & Percent Slope

Key Takeaways Explain This Topic AI

A hub-and-tack stake marks the exact survey point to the nearest hundredth of a foot; because it sits flush with the ground, it is paired with a guard or offset stake carrying the written station, offset, and cut/fill information.

Cut means the existing ground is higher than proposed grade and must be excavated; fill means the existing ground is lower than proposed grade and material must be added.

The Height of Instrument (HI) method computes elevation in two steps: HI equals the known elevation plus the backsight, and the unknown elevation equals HI minus the foresight.

Percent slope equals rise divided by run, multiplied by 100, and is used to check roadway cross slopes, ditch grades, and pipe invert slopes.

A level run should always close back to a known benchmark so the crew can catch and correct reading errors before they are built into the finished grade.

Last updated: July 2026

Why Survey Stakes Exist

Stationing and offsets describe a location on paper, but someone has to translate that plan coordinate into a physical mark the contractor can build to. That is the purpose of a survey stake : a wood or steel marker driven into the ground at, or near, a plan-called point, carrying enough written information for an equipment operator or inspector to find grade without re-surveying the point themselves.

Hub-and-Tack Stakes: The Point of Reference

The most precise stake on a highway project is the hub-and-tack stake: a wooden hub driven flush with the ground, with a small nail or tack in its top marking the exact survey point to the nearest hundredth of a foot. Because a hub is driven flush with the ground, it is easily destroyed by traffic, equipment, or rain, so it is almost always paired with a nearby guard stake (sometimes called a witness stake), driven at an angle and left standing above grade, with the station, offset, and cut/fill information written on it in flagging marker or lumber crayon so the point can still be located and its data read even after the hub itself is gone.

Offset Stakes: Protecting the Point From Construction Traffic

Where a hub would be run over or destroyed by grading or paving equipment before the contractor can use it, the survey crew instead sets an offset stake — a stake placed a fixed, known distance (commonly 5, 10, or 25 ft) away from the true design point, out of the path of construction. The stake is marked with both the offset distance and the cut or fill needed at the true point , not at the stake itself, so the equipment operator or inspector must apply the offset distance first and only then apply the grade information.

Applying an Offset Stake in the Field

A stake at the edge of a proposed lane reads: "10' Rt Offset — C 1.4." The equipment operator needs to know two things before touching the grade: where the true design point is, and how far below the existing ground surface the finished grade sits at that point.

From the stake, measure 10 ft toward the centerline (or as marked) to locate the true design point.

At that true point, "C 1.4" tells the crew to cut, or excavate, 1.4 ft of existing material to reach proposed grade.

Because the offset stake itself sits outside the work area, its own ground elevation is irrelevant to the cut/fill figure — only the true point's cut/fill matters. Reading the offset distance and the cut/fill together, rather than in isolation, is one of the most common sources of grading error on a highway job, and catching that kind of misread is a routine part of the inspector's fieldwork.

Reading Cut and Fill Notation

Cut and fill describe the relationship between the existing ground elevation and the proposed , or design, grade elevation at a given point:

Cut — the existing ground is higher than proposed grade; material must be excavated, or removed, to reach grade

Fill — the existing ground is lower than proposed grade; material must be placed, or added, to reach grade

A grade stake is typically marked with a letter and a number, such as:

  • Notation Meaning
  • C 2.3 Cut 2.3 ft — remove 2.3 ft of material to reach proposed grade
  • F 0.8 Fill 0.8 ft — add 0.8 ft of material to reach proposed grade
  • C 0.0 / F 0.0 (or "Grade") Existing ground already matches proposed grade

The inspector should never assume a stake's cut/fill figure is self-explanatory to the equipment operator; confirming that grading crews are reading the correct stake, at the correct offset, for the correct feature, is a routine and important field check.

Grade Stakes for Slopes, Ditches & Pipe

Beyond the roadway surface itself, grade stakes are used to control side slopes, ditch inverts, and pipe grades — anywhere the finished surface must follow a specific plane or slope rather than a single point elevation. Slope stakes , typically set at the top and bottom of a cut or fill slope, carry the cut/fill at the stake plus the design slope ratio, such as 2:1, so the grading crew can shape the full slope face rather than just the toe or top. Ditch and pipe grade stakes carry the cut/fill needed to establish the correct invert , the flow-line elevation, at each point — a concept tied directly to the percent-slope calculations covered next.

Stake Markings and Local Conventions

Many survey crews use colored flagging or lumber crayon to distinguish stake types at a glance — for example, one color for hubs and guard stakes, another for offset stakes, and another for slope stakes. These color codes are not standardized nationally; they are set by the surveying firm or agency on each project. Rather than assume a color means the same thing job to job, an inspector new to a project should confirm the local key with the survey crew before relying on stake color alone, and should always read the written station, offset, and cut/fill data on the stake itself as the authoritative source.