Study guide
7.1 Main Drain Testing Procedures & The 10% Comparison Rule
NICET Inspection and Testing of Water-Based Systems Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Strategy & Worksite Safety
1.1 NICET ITWBS Level I Exam Overview & Open-Book Strategy 1.2 Personal Protective Equipment, Worksite Hazards & Safety Impairments 1.3 Hazardous Energy Control: Mechanical & Electrical Lockout/Tagout 1.4 Ladder Safety, Elevated Work, Hand Tools & GFCI Protection
2 Chapter 2: Water Supplies, System Types & Fire Pumps
2.1 Water-Based System Types: Wet, Dry, Preaction & Deluge Systems 2.2 Standpipe Systems: Classes, Types & Component Identification 2.3 Water Supply Identification: Municipal Connections, Gravity & Suction Tanks 2.4 Fire Pump Assemblies: Drivers, Controllers, Casing Relief & System Layout
3 Chapter 3: System Valves: Control, Drain, Test & Position
3.1 Control Valve Types, Functions & Identification 3.2 Drain and Test Valves: Main Drains, Inspector's Tests & Auxiliary Drains 3.3 Confirming Control Valve Position, Sealing, Locking & Signage
4 Chapter 4: Visual Inspection: Sprinklers, Piping & Bracing
4.1 Visual Inspection of Sprinklers: Corrosion, Paint, Loading, Clearance & Orientation 4.2 Spare Sprinkler Cabinets, Stock Quantities, Wrenches & Replacement Rules 4.3 Visual Inspection of Pipe, Fittings, Hangers & Seismic Sway Bracing
5 Chapter 5: FDCs, Gauges, Alarms & Supervisory Devices
5.1 Fire Department Connections (FDCs) and Hose Connections Inspection 5.2 Locating and Reading Pressure Gauges: Wet, Dry, Deluge & Fire Pump Systems 5.3 Alarm and Supervisory Devices: Mechanical Water Motor Gongs vs Electrical Devices 5.4 Signal Verification: Alarm, Supervisory & Trouble Signals at the FACP
6 Chapter 6: Operating Components: Valves & Flow Alarms
6.1 Control Valve Exercising: Operating Procedures, Back-Off Rules & Frequencies 6.2 Waterflow Alarm Testing: Water Motor Gongs, Pressure Switches & Vane-Type Devices 6.3 Electronic Valve Supervisory Device Testing: Tamper Switches & Restoration
7 Chapter 7: Operating Components: Drains, Hydrants & Hoses
7.1 Main Drain Testing Procedures & The 10% Comparison Rule 7.2 Private Fire Hydrant Flushing & Inspection Procedures 7.3 Exercising Hose Connections & Pressure Restricting/Reducing Devices
8 Chapter 8: Documentation, Inventory, Specs & Owner Responsibilities
8.1 NFPA 25 Inspection, Testing, and Maintenance Reporting Forms & Records 8.2 System Component Inventory & Identification: Sprinklers, SINs, Valves & Nameplates 8.3 Preparing Preliminary Reports & Deficiency Classification 8.4 Owner Responsibilities, Impairment Procedures & Record Retention Rules
7.1 Main Drain Testing Procedures & The 10% Comparison Rule
Key Takeaways Explain This Topic AI
NFPA 25 (2023) places main-drain requirements in Section 13.2.2; the summary table provides annual or quarterly frequencies as applicable.
Record static pressure, fully open the drain safely, allow flow pressure to stabilize, record full-flow pressure, close slowly, and verify return to normal.
Compare current full-flow pressure with the original acceptance or previous comparable full-flow result—not current static versus current flow.
A 10 percent reduction in full-flow pressure requires the cause to be identified and corrected if necessary.
The threshold triggers investigation; the condition category depends on the cause and effect and is not automatically one universal deficiency label.
Last updated: October 2026
7.1 Main-Drain Testing and the 10 Percent Comparison
A main-drain test provides a repeatable indication of water-supply condition at a riser. It is not a full fire-flow test and does not by itself prove hydraulic adequacy. The useful result comes from a controlled procedure and comparison with a valid earlier test under similar conditions.
Current reference and frequency
In NFPA 25 (2023), main-drain provisions are in Section 13.2.2 , not the 13.2.5 numbering found in older editions. Table 13.1.1.2 lists the main-drain test at annual or quarterly intervals as applicable . Use the current table, its notes, and Section 13.2.2 to determine the installation's frequency. Do not attach an old subsection number to a remembered backflow or pressure-reducing arrangement.
Preparation
Identify the correct riser, main-drain valve, supply and system gauges, and discharge route. Compare the setup with the prior record. Confirm that the drain can carry full flow without flooding, erosion, ice, exposure to traffic, or contact with electrical equipment. Establish required alarm and monitoring notifications because water movement can operate devices.
Record initial system status and static pressure. Use the same gauge as the prior test when possible and note its identifier, range, and units. Municipal demand, pump operation, tank level, and other water use can affect results, so record unusual conditions that could impair comparison.
Procedure under direct supervision
Record the static supply pressure with the main drain closed and no test flow.
Open the main-drain valve fully in a controlled manner.
Allow the pressure to stabilize while observing the discharge.
Record the full-flow pressure and any required time or discharge observation.
Close the drain slowly to limit water hammer.
Verify that the valve is fully closed, leakage stops, pressure returns toward normal, and alarms or monitoring status restore.
Stop if the drain cannot handle the flow, piping moves dangerously, the gauge fails, uncontrolled leakage develops, or another unexpected condition occurs. Do not throttle the valve to produce a preferred pressure. A partially open drain invalidates comparison with a full-open prior test.
Correct calculation
NFPA 25 Section 13.2.2.3 addresses a 10 percent reduction in full-flow pressure compared with the original acceptance test or a previously performed test. The percentage reduction is:
(previous full-flow pressure − current full-flow pressure) ÷ previous full-flow pressure × 100
If the previous comparable full-flow pressure was 60 psi and the current full-flow pressure is 48 psi:
(60 − 48) ÷ 60 × 100 = 20%
This exceeds 10 percent, so the cause must be identified and corrected if necessary. Do not calculate (static − current flow) ÷ static and call that the historical ten-percent comparison. The static-to-flow drop within one test describes that test condition but is not the comparison specified by the rule.
Interpretation
A reduction can be associated with water-supply change, a valve not fully open, obstruction, backflow-device condition, gauge error, noncomparable flow, or another cause. The Level I technician records the facts and immediately informs the supervisor. Investigation may include confirming valve positions, gauges, test setup, and supply conditions under an approved plan.
Do not state that every result above 10 percent is automatically a critical deficiency or automatically an impairment. NFPA 25 classification depends on the actual condition and its effect on system performance. The threshold means investigation is required.
A result below 10 percent is not a blanket declaration that every supply component is satisfactory. Abnormal static pressure, poor recovery, leakage, valve problems, or other evidence still must be reported.
Documentation
Record property, riser, drain and gauge identifiers, date and time, initial static pressure, stabilized full-flow pressure, final static or recovery observation, prior comparison value and date, calculated percentage, discharge condition, notifications, and restoration. State whether the drain was fully opened and whether alarms were restored.
If the prior test used a different gauge, drain position, or supply condition, flag the comparison limitation. A precise record lets the supervisor distinguish a water-supply trend from a test-method difference and decide what investigation is required.
Exam focus
Keep the denominator straight: the prior comparable full-flow result is the baseline. A current static-to-flow difference is not the historical percentage. Also separate the threshold from the diagnosis—ten percent calls for investigation, while the discovered cause determines classification and correction.