Study guide
7.4 Nitrogen Generation Systems & Gas Separation Membranes
NICET Inspection and Testing of Water-Based Systems Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Personal Safety, PPE & Equipment
1.1 PPE Requirements & Maintenance 1.2 Tool Safety, Electrical Safety & Stored-Energy Hazards in Charged Piping 1.3 Environmental Hazards, Hazardous Materials & Worksite Illumination
2 Chapter 2: High-Hazard Safety: LOTO, Confined Space & Working at Heights
2.1 Lockout/Tagout (LOTO) Procedures 2.2 Permit-Required Confined Spaces & Atmospheric Testing 2.3 Ladder Safety, Scaffolding & Aerial Lifts
3 Chapter 3: Customer Coordination & Pre-Inspection Scope
3.1 Pre-Inspection Review, Scope of Work & Scheduling 3.2 Stakeholder Notifications: Owners, Designated Representatives & Facility Operations 3.3 Safety Impairment Procedures & Site-Specific Hazard Protocols
4 Chapter 4: Stakeholder Notification, Reporting & Impairment Procedures
4.1 Central Station Alarm Monitoring & AHJ Notifications Before/After Testing 4.2 NFPA 25 Chapter 15 Impairment Program: Coordinator, Tagging & Fire Watch Rules 4.3 ITM Documentation, Record Retention & Delivering Deficiency Reports
5 Chapter 5: Wet Sprinkler Systems ITM
5.1 Gauges, Control Valves & Visual Inspection Frequencies 5.2 Waterflow Alarm Devices: Vane-Type Paddle Switches & Mechanical Gongs 5.3 Main Drain Test Procedure & the 10% Pressure Drop Rule 5.4 Sprinkler Head Inspection, Clearance & Laboratory Testing Age Triggers
6 Chapter 6: Wet System Specialized Components: Antifreeze & Air Vents
6.1 Antifreeze Systems: Types, Listed Solutions, Backflow Isolation & Testing Procedures 6.2 Antifreeze Solution Measurement: Refractometer / Hydrometer & Freeze-Point Verification 6.3 Automatic Air Vents & Nitrogen Inerting in Wet Systems
7 Chapter 7: Dry Pipe Systems & Specialized Equipment
7.1 Dry Pipe Valve Principles, Differential Ratios & Priming Water Level 7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing 7.3 Dedicated Air Compressors, Automatic Air Maintenance Devices (AMDs) & Regulators 7.4 Nitrogen Generation Systems & Gas Separation Membranes
8 Chapter 8: Dry System Testing & Operational Verification
8.1 Annual Partial Trip Test vs. Three-Year Full Flow Trip Test 8.2 Three-Year Air-Leakage Options and Annual Air-Pressure Supervisory Testing 8.3 Dry Pipe Auxiliary Drains (Drum Drips) & Condensate Management in Freezing Weather
9 Chapter 9: Standpipe Systems & Deficiency Classification
9.1 Standpipe Classes (I, II, III), System Types & Component Visual Inspections 9.2 Standpipe 5-Year Hydrostatic & Flow Testing Requirements (500 gpm / 250 gpm) 9.3 Hose Valves, Pressure Regulating Devices (PRDs/PRVs) & FDC Inspection and Testing
10 Chapter 10: Fire Pump Systems & Drivers
10.1 Fire Pump Types (Horizontal Split Case, Vertical Turbine, End Suction) & System Arrangements 10.2 Fire Pump Drivers: Electric Motors, Diesel Engines & Controller Components 10.3 Pressure-Maintenance Pumps: Purpose, Capacity, and Coordinated Settings
11 Chapter 11: Fire Pump Inspection, Testing & Maintenance
11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests 11.2 Annual Fire Pump Flow Test: Churn (0%), 100% Rated Flow & 150% Peak Flow 11.3 Pump Performance Evaluation: Net/Gross Curves and the Complete Acceptance Criteria 11.4 Diesel Support-System Maintenance and Electric-Pump Alternate Power
12 Chapter 12: Private Fire Service Mains & Hydrants
12.1 Underground Piping ITM & 5-Year Underground Flow Testing 12.2 Fire Hydrant Inspection, Lubrication & Annual Drainage Operational Tests 12.3 NFPA 291 Water Flow Testing: Layout, Pitot Readings & Flow Math 12.4 Hydrant Classification, Color Coding & Available Flow Extrapolation at 20 psi Residual
13 Chapter 13: Water Storage Tanks
13.1 Tank Types (Suction, Elevated, Pressure) & Component Overview 13.2 Inspection Frequencies: Water Level, Temperature (Min 40°F), Exterior & Interior 13.3 Tank Heating Systems, Low-Water Alarms, Vents, Overflow & Anti-Vortex Plates
14 Chapter 14: Internal Pipe Assessment & Obstruction Triggers
14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing 14.2 The Sixteen NFPA 25 (2023) Obstruction-Investigation Triggers 14.3 Five-Location Obstruction Examination, Evidence, and Required Follow-Up
15 Chapter 15: Flushing Methods, Contaminants & Deficiency Classification
15.1 Obstruction Materials: Corrosion, MIC Indicators, Scale, Ice, and Foreign Debris 15.2 Hydraulic Flushing: Program Scope, Velocity Calculations, and Completion Evidence 15.3 Specialist Cleaning Methods: Suitability, Safety Controls, and Restoration 15.4 Classifying Findings: Impairments vs. Critical Deficiencies vs. Noncritical Deficiencies
7.4 Nitrogen Generation Systems & Gas Separation Membranes
Key Takeaways Explain This Topic AI
Nitrogen reduces oxygen exposure but does not guarantee zero corrosion, a particular dew point, or a fixed service life.
For increased-C-value systems, verify at least 98% concentration semiannually, with the stated annual constantly supervised-monitoring exception.
Generator inspection, operational testing, concentration verification, and manufacturer maintenance are distinct duties.
Loss of the design-required C=120 nitrogen supply invokes the Chapter 14 provision with its stated exception.
Last updated: October 2026
Nitrogen reduces one contributor to corrosion
Dry and preaction piping can retain moisture after operation or condensation. Oxygen exposure in those conditions can contribute to corrosion and obstruction. Nitrogen supply can reduce oxygen exposure under an appropriate design, while drainage, leak correction, assessment, and maintenance remain necessary. Do not promise zero corrosion, immunity to MIC, a fixed pipe life, or freedom from ice from one purity reading.
Identify the generator, compressor/source, tanks, filtration, purge arrangement, analyzer, sample points, and systems served. Record whether the approved design relies on nitrogen to permit an increased Hazen-Williams C value. That design dependency changes the significance of supply and concentration findings. An inspector must not assume that fitting a generator automatically permits smaller pipe or a different hydraulic calculation.
Understand separation at a useful level
A membrane generator uses different gas permeation rates to produce nitrogen-enriched output from compressed air. Appropriate filtration and moisture control protect the separation equipment. The Potter INS-1000 description illustrates membrane separation followed by gas delivery and system purging. It is one product example, not a universal filter train or valve layout.
Other equipment can use pressure-swing adsorption, cycling between adsorption and regeneration conditions. The actual equipment determines pressures, valves, capacity, maintenance, and analyzer requirements. Do not memorize an unsupported universal dew point, filter micron size, oil concentration, or ten-year module life as an NFPA rule. Use the installed manufacturer's current instructions and service information.
Concentration requirements for increased-C-value systems
NFPA 25 (2023), 13.4.5.2.10 for dry systems and 13.4.3.2.14 for preaction, requires semiannual testing to verify at least 98% nitrogen where nitrogen permits the increased design C value under NFPA 13. Where concentration is monitored at a constantly supervised location, the stated annual verification exception applies. Below 98%, identify and correct the cause under the applicable provision.
Verify through the specified system sampling arrangement and suitable instrument. An outlet display at the generator does not establish the concentration in every connected remote pipe. Purging, leakage, valve positions, and sample method can affect readings. Identify system, sample point, instrument, date, operating condition, measured concentration, and follow-up. Do not choose only the most favorable point and report it as an unqualified result for all risers.
Observation What it establishes What still needs evaluation
Generator outlet at 99% Output concentration at that point under the method System distribution and required sample verification
Remote required sample at 95% Concentration below the 98% criterion there Instrument/method and actual cause/correction
High compressor run hours Abnormal demand or performance may exist Leakage, controls, purge, and supply condition
A normal purity result The tested concentration criterion Drainage, obstruction, and other readiness requirements
Inspection and operational testing
Section 13.10 requires monthly inspection of dedicated compressors/generators for physical damage, wiring and supply-piping condition, secure attachment, and oil level where applicable. Operational testing is annual for the prescribed response and restoration of normal supervisory pressure within the required time. These duties are separate from concentration verification. A cabinet passing its annual start test does not establish that a remote system has reached the required purity.
Maintenance and calibration follow the actual manufacturer instructions and applicable provisions. Check filters, drains, purge devices, analyzer condition, and alarms through the defined method. There is no universal annual replacement of every filter in every design. A blocked filter or incorrect purge arrangement can affect capacity or purity; diagnose before replacing unrelated parts or raising pressure.
Loss of a design-required supply
Chapter 14 includes failure to maintain the nitrogen supply installed for a dry/preaction C=120 design as an investigation trigger, with the stated preplanned-impairment exception. Apply that provision rather than inventing a universal grace period or assuming ordinary compressed air is always an acceptable permanent substitute. Coordinate the protection status, required investigation, correction, and restoration with the owner.
A generator shutdown can have several effects: reduced gas replenishment, declining concentration over time, or loss of an approved design assumption. Establish the actual arrangement and elapsed condition from records. An inspector should not conclude from the stopped cabinet alone that every sprinkler is immediately blocked, nor ignore the design-dependent trigger because the riser still shows pressure.
Work safely and preserve evidence
Nitrogen can displace oxygen in enclosed rooms, pits, and tanks. Arrange appropriate ventilation and atmospheric controls; never use nitrogen as breathing air. Equipment also has electrical and stored-pressure hazards. Isolate safely before internal maintenance and preserve fire protection through the impairment process when necessary.
After correction, verify required concentration and operation through the prescribed methods, normal valves and purge arrangement, supervisory pressure, alarms, and final status. Keep results and service records available for the next comparison. A defensible report states what was tested and restored rather than promising that nitrogen has eliminated every future corrosion or ice problem.
Sources checked October 19, 2026: NFPA 25 (2023), 13.10, 13.4.5.2.10, 13.4.3.2.14, and 14.3.1(16); Potter manufacturer resources linked above.