Study guide
7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing
NICET Inspection and Testing of Water-Based Systems Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Personal Safety, PPE & Equipment
1.1 PPE Requirements & Maintenance 1.2 Tool Safety, Electrical Safety & Stored-Energy Hazards in Charged Piping 1.3 Environmental Hazards, Hazardous Materials & Worksite Illumination
2 Chapter 2: High-Hazard Safety: LOTO, Confined Space & Working at Heights
2.1 Lockout/Tagout (LOTO) Procedures 2.2 Permit-Required Confined Spaces & Atmospheric Testing 2.3 Ladder Safety, Scaffolding & Aerial Lifts
3 Chapter 3: Customer Coordination & Pre-Inspection Scope
3.1 Pre-Inspection Review, Scope of Work & Scheduling 3.2 Stakeholder Notifications: Owners, Designated Representatives & Facility Operations 3.3 Safety Impairment Procedures & Site-Specific Hazard Protocols
4 Chapter 4: Stakeholder Notification, Reporting & Impairment Procedures
4.1 Central Station Alarm Monitoring & AHJ Notifications Before/After Testing 4.2 NFPA 25 Chapter 15 Impairment Program: Coordinator, Tagging & Fire Watch Rules 4.3 ITM Documentation, Record Retention & Delivering Deficiency Reports
5 Chapter 5: Wet Sprinkler Systems ITM
5.1 Gauges, Control Valves & Visual Inspection Frequencies 5.2 Waterflow Alarm Devices: Vane-Type Paddle Switches & Mechanical Gongs 5.3 Main Drain Test Procedure & the 10% Pressure Drop Rule 5.4 Sprinkler Head Inspection, Clearance & Laboratory Testing Age Triggers
6 Chapter 6: Wet System Specialized Components: Antifreeze & Air Vents
6.1 Antifreeze Systems: Types, Listed Solutions, Backflow Isolation & Testing Procedures 6.2 Antifreeze Solution Measurement: Refractometer / Hydrometer & Freeze-Point Verification 6.3 Automatic Air Vents & Nitrogen Inerting in Wet Systems
7 Chapter 7: Dry Pipe Systems & Specialized Equipment
7.1 Dry Pipe Valve Principles, Differential Ratios & Priming Water Level 7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing 7.3 Dedicated Air Compressors, Automatic Air Maintenance Devices (AMDs) & Regulators 7.4 Nitrogen Generation Systems & Gas Separation Membranes
8 Chapter 8: Dry System Testing & Operational Verification
8.1 Annual Partial Trip Test vs. Three-Year Full Flow Trip Test 8.2 Three-Year Air-Leakage Options and Annual Air-Pressure Supervisory Testing 8.3 Dry Pipe Auxiliary Drains (Drum Drips) & Condensate Management in Freezing Weather
9 Chapter 9: Standpipe Systems & Deficiency Classification
9.1 Standpipe Classes (I, II, III), System Types & Component Visual Inspections 9.2 Standpipe 5-Year Hydrostatic & Flow Testing Requirements (500 gpm / 250 gpm) 9.3 Hose Valves, Pressure Regulating Devices (PRDs/PRVs) & FDC Inspection and Testing
10 Chapter 10: Fire Pump Systems & Drivers
10.1 Fire Pump Types (Horizontal Split Case, Vertical Turbine, End Suction) & System Arrangements 10.2 Fire Pump Drivers: Electric Motors, Diesel Engines & Controller Components 10.3 Pressure-Maintenance Pumps: Purpose, Capacity, and Coordinated Settings
11 Chapter 11: Fire Pump Inspection, Testing & Maintenance
11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests 11.2 Annual Fire Pump Flow Test: Churn (0%), 100% Rated Flow & 150% Peak Flow 11.3 Pump Performance Evaluation: Net/Gross Curves and the Complete Acceptance Criteria 11.4 Diesel Support-System Maintenance and Electric-Pump Alternate Power
12 Chapter 12: Private Fire Service Mains & Hydrants
12.1 Underground Piping ITM & 5-Year Underground Flow Testing 12.2 Fire Hydrant Inspection, Lubrication & Annual Drainage Operational Tests 12.3 NFPA 291 Water Flow Testing: Layout, Pitot Readings & Flow Math 12.4 Hydrant Classification, Color Coding & Available Flow Extrapolation at 20 psi Residual
13 Chapter 13: Water Storage Tanks
13.1 Tank Types (Suction, Elevated, Pressure) & Component Overview 13.2 Inspection Frequencies: Water Level, Temperature (Min 40°F), Exterior & Interior 13.3 Tank Heating Systems, Low-Water Alarms, Vents, Overflow & Anti-Vortex Plates
14 Chapter 14: Internal Pipe Assessment & Obstruction Triggers
14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing 14.2 The Sixteen NFPA 25 (2023) Obstruction-Investigation Triggers 14.3 Five-Location Obstruction Examination, Evidence, and Required Follow-Up
15 Chapter 15: Flushing Methods, Contaminants & Deficiency Classification
15.1 Obstruction Materials: Corrosion, MIC Indicators, Scale, Ice, and Foreign Debris 15.2 Hydraulic Flushing: Program Scope, Velocity Calculations, and Completion Evidence 15.3 Specialist Cleaning Methods: Suitability, Safety Controls, and Restoration 15.4 Classifying Findings: Impairments vs. Critical Deficiencies vs. Noncritical Deficiencies
7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing
Key Takeaways Explain This Topic AI
Conventional accelerators affect a compatible valve’s differential; exhausters speed gas release, while actual products vary.
Test QODs quarterly using the permitted method for the installed arrangement.
Use actual anti-flooding, internal-maintenance, and reset instructions; never enlarge a restricted orifice.
Verify the QOD is restored to the complete protective arrangement, not merely that it responded while isolated.
Last updated: October 2026
QODs improve response through the listed arrangement
A quick-opening device (QOD) helps a dry system respond to gas-pressure loss. Whether a system requires one depends on its approved installation criteria, volume/delivery method, and listed arrangement. Do not impose a universal 500-gallon threshold or sixty-second maximum on every existing system. Identify the actual device and its compatible valve before planning an operational test or reset.
An accelerator and an exhauster can achieve faster valve operation through different actions. In a conventional compatible accelerator arrangement, a rapid pressure reduction causes the device to transmit system pressure to the dry valve's intermediate chamber, overcoming the differential balance. An exhauster releases gas to atmosphere to speed pressure reduction. Modern products can use other listed mechanisms; the category name alone does not define every internal part or connection.
Rate response and gradual pressure changes
A conventional pneumatic accelerator compares pressures in communicating chambers through a restriction. Slow pressure changes can equalize, while a sufficiently rapid sustained reduction produces the operating differential. The actual response threshold, chamber filling time, and reset condition are product specific. Do not use an invented universal ten-second response or assume an isolated device has operated because its gauge pointer moved.
The TYCO ACC-1 description illustrates this conventional mechanism for its compatible DPV-1 valve. That example supports understanding; it is not authorization to install the same accelerator on an unrelated valve. Confirm the listing, trim diagram, pressure range, and actual technical instructions.
- Feature Conventional accelerator example Exhauster principle
- Response objective Accelerate valve operation Accelerate system depressurization
- Action Affect compatible differential valve operation Release system gas through a larger path
- Performance details Actual model and trim govern Actual model and system govern
- Inspection/test basis NFPA 25 plus listed instructions NFPA 25 plus listed instructions
- Quarterly operational testing
NFPA 25 (2023) requires QOD operational testing quarterly. The annual dry-valve trip test does not replace the quarterly requirement. A permitted listed arrangement can allow testing the QOD while isolating it from the dry valve; otherwise use the applicable complete test method. Verify exactly what the selected method demonstrates and record the device, isolation arrangement, and observed response.
Coordinate notifications and any impairment before operating the trim. Review the actual manufacturer test procedure, ensure suitable drainage, and establish the required starting pressure. Use the intended test connection and observe operation. Do not intentionally flood an accelerator, remove a pressurized plug, or manipulate a valve not identified on the approved procedure. If the procedure cannot be completed safely, record the limitation and arrange the necessary work.
A device can respond locally while remaining isolated from the valve it is meant to operate. Therefore restoration of the QOD's prescribed control-valve position is part of completion. Conversely, an annual valve trip without the installed QOD in its required operating arrangement cannot demonstrate that accessory's complete intended function. Record the actual configuration rather than only a checkbox marked “trip passed.”
Protection from water and contamination
Accelerators can have integral or separate anti-flooding features protecting sensitive passages from water and debris. Their design and reset are model specific. Do not teach that every device has an identical float, piston, latch, or manually operated reset button. Check the actual instructions and inspect the protection arrangement when required. Water contamination or a blocked restricted passage can prevent correct response.
Internal strainers, filters, and restricted orifices have the applicable five-year inspection/cleaning requirement and any more frequent manufacturer or condition-based work. Isolate and depressurize before disassembly. Use the specified parts and cleaning method; do not enlarge an orifice with a drill or wire to make the device refill faster. That changes the operating characteristic and can defeat its intended response.
Reset as a complete procedure
The dry valve, system gas pressure, QOD chambers, isolation valves, and any anti-flood device must be restored in the product's specified sequence. Some procedures require timed chamber filling or verification at a particular pressure. A generic six-step diagram cannot replace that model-specific process. Obtain the current technical sheet and confirm each required observation, not only the last handle position.
If the QOD trips unexpectedly during reset, investigate the actual cause. Pressure instability, incorrect sequence, blocked passages, leakage, or damaged parts can produce similar symptoms. Do not automatically diagnose a ruptured diaphragm from a single hiss. Record observations and arrange qualified correction and retest. Verify normal pressure, all required valve positions, drain condition, monitoring, and final protection status before ending the work.
Sources checked October 19, 2026: NFPA 25 (2023), 13.4.5.2 and applicable maintenance provisions; TYCO ACC-1 manufacturer description and technical resources.