Study guide

11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests

NICET Inspection and Testing of Water-Based Systems Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Personal Safety, PPE & Equipment

1.1 PPE Requirements & Maintenance 1.2 Tool Safety, Electrical Safety & Stored-Energy Hazards in Charged Piping 1.3 Environmental Hazards, Hazardous Materials & Worksite Illumination

2 Chapter 2: High-Hazard Safety: LOTO, Confined Space & Working at Heights

2.1 Lockout/Tagout (LOTO) Procedures 2.2 Permit-Required Confined Spaces & Atmospheric Testing 2.3 Ladder Safety, Scaffolding & Aerial Lifts

3 Chapter 3: Customer Coordination & Pre-Inspection Scope

3.1 Pre-Inspection Review, Scope of Work & Scheduling 3.2 Stakeholder Notifications: Owners, Designated Representatives & Facility Operations 3.3 Safety Impairment Procedures & Site-Specific Hazard Protocols

4 Chapter 4: Stakeholder Notification, Reporting & Impairment Procedures

4.1 Central Station Alarm Monitoring & AHJ Notifications Before/After Testing 4.2 NFPA 25 Chapter 15 Impairment Program: Coordinator, Tagging & Fire Watch Rules 4.3 ITM Documentation, Record Retention & Delivering Deficiency Reports

5 Chapter 5: Wet Sprinkler Systems ITM

5.1 Gauges, Control Valves & Visual Inspection Frequencies 5.2 Waterflow Alarm Devices: Vane-Type Paddle Switches & Mechanical Gongs 5.3 Main Drain Test Procedure & the 10% Pressure Drop Rule 5.4 Sprinkler Head Inspection, Clearance & Laboratory Testing Age Triggers

6 Chapter 6: Wet System Specialized Components: Antifreeze & Air Vents

6.1 Antifreeze Systems: Types, Listed Solutions, Backflow Isolation & Testing Procedures 6.2 Antifreeze Solution Measurement: Refractometer / Hydrometer & Freeze-Point Verification 6.3 Automatic Air Vents & Nitrogen Inerting in Wet Systems

7 Chapter 7: Dry Pipe Systems & Specialized Equipment

7.1 Dry Pipe Valve Principles, Differential Ratios & Priming Water Level 7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing 7.3 Dedicated Air Compressors, Automatic Air Maintenance Devices (AMDs) & Regulators 7.4 Nitrogen Generation Systems & Gas Separation Membranes

8 Chapter 8: Dry System Testing & Operational Verification

8.1 Annual Partial Trip Test vs. Three-Year Full Flow Trip Test 8.2 Three-Year Air-Leakage Options and Annual Air-Pressure Supervisory Testing 8.3 Dry Pipe Auxiliary Drains (Drum Drips) & Condensate Management in Freezing Weather

9 Chapter 9: Standpipe Systems & Deficiency Classification

9.1 Standpipe Classes (I, II, III), System Types & Component Visual Inspections 9.2 Standpipe 5-Year Hydrostatic & Flow Testing Requirements (500 gpm / 250 gpm) 9.3 Hose Valves, Pressure Regulating Devices (PRDs/PRVs) & FDC Inspection and Testing

10 Chapter 10: Fire Pump Systems & Drivers

10.1 Fire Pump Types (Horizontal Split Case, Vertical Turbine, End Suction) & System Arrangements 10.2 Fire Pump Drivers: Electric Motors, Diesel Engines & Controller Components 10.3 Pressure-Maintenance Pumps: Purpose, Capacity, and Coordinated Settings

11 Chapter 11: Fire Pump Inspection, Testing & Maintenance

11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests 11.2 Annual Fire Pump Flow Test: Churn (0%), 100% Rated Flow & 150% Peak Flow 11.3 Pump Performance Evaluation: Net/Gross Curves and the Complete Acceptance Criteria 11.4 Diesel Support-System Maintenance and Electric-Pump Alternate Power

12 Chapter 12: Private Fire Service Mains & Hydrants

12.1 Underground Piping ITM & 5-Year Underground Flow Testing 12.2 Fire Hydrant Inspection, Lubrication & Annual Drainage Operational Tests 12.3 NFPA 291 Water Flow Testing: Layout, Pitot Readings & Flow Math 12.4 Hydrant Classification, Color Coding & Available Flow Extrapolation at 20 psi Residual

13 Chapter 13: Water Storage Tanks

13.1 Tank Types (Suction, Elevated, Pressure) & Component Overview 13.2 Inspection Frequencies: Water Level, Temperature (Min 40°F), Exterior & Interior 13.3 Tank Heating Systems, Low-Water Alarms, Vents, Overflow & Anti-Vortex Plates

14 Chapter 14: Internal Pipe Assessment & Obstruction Triggers

14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing 14.2 The Sixteen NFPA 25 (2023) Obstruction-Investigation Triggers 14.3 Five-Location Obstruction Examination, Evidence, and Required Follow-Up

15 Chapter 15: Flushing Methods, Contaminants & Deficiency Classification

15.1 Obstruction Materials: Corrosion, MIC Indicators, Scale, Ice, and Foreign Debris 15.2 Hydraulic Flushing: Program Scope, Velocity Calculations, and Completion Evidence 15.3 Specialist Cleaning Methods: Suitability, Safety Controls, and Restoration 15.4 Classifying Findings: Impairments vs. Critical Deficiencies vs. Noncritical Deficiencies

11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests

Key Takeaways Explain This Topic AI

Diesel no-flow tests normally occur weekly for at least 30 minutes; the approved risk-analysis provision can alter frequency.

Electric tests run at least ten minutes; weekly versus permitted monthly frequency depends on the specified categories and exceptions.

Keep normal system suction/discharge/bypass control valves in their prescribed open positions; close the test outlets for churn.

Verify automatic response, required observations, safe cooling, and complete restoration.

Last updated: October 2026

Select frequency from the installed category

A no-flow or churn test demonstrates starting and short-duration operating readiness without discharging the rated test flow. It does not establish that the pump can meet the system's hydraulic demand. NFPA 25 (2023), 8.3.1 and 8.3.2, separates frequency from duration: first determine when this pump must be tested, then run it for the required minimum time and make the pertinent observations.

Diesel pumps normally require weekly no-flow testing, with a minimum 30-minute run. An approved risk analysis can establish the permitted alternative frequency. Do not call a longer interval acceptable merely because the engine is new or has remote indication. The risk-analysis approval and applicable automated-test provisions must actually be satisfied.

Electric pumps run at least 10 minutes. The weekly categories include pumps serving buildings beyond fire department pumping capacity, pumps with limited-service controllers, vertical turbine pumps, and pumps taking suction from ground-level tanks or sources without materially useful pressure in the pump's absence. Monthly testing is permitted for other electric pumps and for the specified redundant-pump arrangements. An approved risk analysis is another permitted basis. A VFD or phase-monitoring indicator is not, by itself, the criterion allowing every electric pump to move to monthly testing.

  • Driver/arrangement Usual frequency basis Minimum run
  • Diesel Weekly unless approved risk-analysis provision applies 30 minutes
  • Electric in specified weekly category Weekly, subject to stated exceptions 10 minutes
  • Other qualifying electric arrangement Monthly permitted 10 minutes

Approved alternative Documented applicable risk-analysis or automated-test provisions Applicable required duration and observations

Prepare the correct valve positions

Check the pump room and weekly inspection items, controller mode, source availability, and drainage. Keep normal suction, system discharge, and bypass control valves open as prescribed. Keep test-header outlets and test valves in their specified closed position for a no-flow test. Closing the system discharge valve merely to create “zero flow” can isolate the building from its pump. No-flow describes the absence of test demand; it does not authorize blocking the normal protective supply.

Verify the applicable cooling and relief arrangements. A small circulation-relief discharge can be necessary to prevent overheating. It is different from intentional rated-flow testing and from a main relief valve opening improperly. Observe actual temperatures and discharge. Stop or correct unsafe conditions through the proper procedure rather than continuing a timed run while the pump overheats.

Initiate automatically and observe

Start the pump automatically through the prescribed test means, such as the provided pressure-drop arrangement for a pressure-actuated controller. Record start pressure and response. A manual-start test alone does not establish pressure-start operation. Do not open an energized electric controller or defeat a pressure sensor to produce the required event. Use approved external controls and instruments and arrange qualified work for any limitation.

Qualified personnel attend the test unless the complete remotely monitored automated-test provisions apply. A timer alone does not replace attendance and observations. Watch for leakage, abnormal noise, excessive vibration, packing or seal problems, cooling issues, and driver/controller abnormalities. For diesel equipment, observe lubrication and cooling indications, fuel supply, batteries/charging, and exhaust/ventilation as applicable. For electric equipment, record the available external electrical information and phase/controller status.

A normal-looking discharge gauge does not establish adequate suction or correct speed. Record the relevant suction and discharge pressures, driver speed where required, and the other specified observations. Compare with prior tests to identify trends. If a new vibration develops, finish the safety response and evaluate the cause; do not label it harmless merely because the pump completed ten minutes.

Timing and stopping

Run an electric pump for at least ten minutes and a diesel pump for at least thirty minutes under the applicable procedure. Record actual start and stop times. A five-minute diesel test is incomplete even if the engine starts instantly. Follow manufacturer instructions and the approved controller arrangement for stopping and any necessary cooldown. Do not invent a universal cooldown duration for every engine or alter the controller's stopping logic during the visit.

Restore and classify

Confirm the controller is in the required automatic mode, supply and system valves are normal, test connections are closed, cooling and drainage arrangements are restored, and alarms/monitoring are normal. Notify the responsible parties that the test is complete and identify any remaining loss of protection. Preserve the results and access limitations in the record.

A failed automatic start can be an impairment even if someone can force the pump to run manually. An unusual indication requires evaluation of actual system effect. Apply Chapter 15 when protection is out of service and arrange the required corrective work and retest. Passing the churn test does not excuse a failed annual flow test or an inadequate supply.

Source checked October 19, 2026: NFPA 25 (2023), 8.2, 8.3.1, and 8.3.2.