Study guide
14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing
NICET Inspection and Testing of Water-Based Systems Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Personal Safety, PPE & Equipment
1.1 PPE Requirements & Maintenance 1.2 Tool Safety, Electrical Safety & Stored-Energy Hazards in Charged Piping 1.3 Environmental Hazards, Hazardous Materials & Worksite Illumination
2 Chapter 2: High-Hazard Safety: LOTO, Confined Space & Working at Heights
2.1 Lockout/Tagout (LOTO) Procedures 2.2 Permit-Required Confined Spaces & Atmospheric Testing 2.3 Ladder Safety, Scaffolding & Aerial Lifts
3 Chapter 3: Customer Coordination & Pre-Inspection Scope
3.1 Pre-Inspection Review, Scope of Work & Scheduling 3.2 Stakeholder Notifications: Owners, Designated Representatives & Facility Operations 3.3 Safety Impairment Procedures & Site-Specific Hazard Protocols
4 Chapter 4: Stakeholder Notification, Reporting & Impairment Procedures
4.1 Central Station Alarm Monitoring & AHJ Notifications Before/After Testing 4.2 NFPA 25 Chapter 15 Impairment Program: Coordinator, Tagging & Fire Watch Rules 4.3 ITM Documentation, Record Retention & Delivering Deficiency Reports
5 Chapter 5: Wet Sprinkler Systems ITM
5.1 Gauges, Control Valves & Visual Inspection Frequencies 5.2 Waterflow Alarm Devices: Vane-Type Paddle Switches & Mechanical Gongs 5.3 Main Drain Test Procedure & the 10% Pressure Drop Rule 5.4 Sprinkler Head Inspection, Clearance & Laboratory Testing Age Triggers
6 Chapter 6: Wet System Specialized Components: Antifreeze & Air Vents
6.1 Antifreeze Systems: Types, Listed Solutions, Backflow Isolation & Testing Procedures 6.2 Antifreeze Solution Measurement: Refractometer / Hydrometer & Freeze-Point Verification 6.3 Automatic Air Vents & Nitrogen Inerting in Wet Systems
7 Chapter 7: Dry Pipe Systems & Specialized Equipment
7.1 Dry Pipe Valve Principles, Differential Ratios & Priming Water Level 7.2 Quick-Opening Devices (QODs): Accelerators & Exhausters Inspection and Testing 7.3 Dedicated Air Compressors, Automatic Air Maintenance Devices (AMDs) & Regulators 7.4 Nitrogen Generation Systems & Gas Separation Membranes
8 Chapter 8: Dry System Testing & Operational Verification
8.1 Annual Partial Trip Test vs. Three-Year Full Flow Trip Test 8.2 Three-Year Air-Leakage Options and Annual Air-Pressure Supervisory Testing 8.3 Dry Pipe Auxiliary Drains (Drum Drips) & Condensate Management in Freezing Weather
9 Chapter 9: Standpipe Systems & Deficiency Classification
9.1 Standpipe Classes (I, II, III), System Types & Component Visual Inspections 9.2 Standpipe 5-Year Hydrostatic & Flow Testing Requirements (500 gpm / 250 gpm) 9.3 Hose Valves, Pressure Regulating Devices (PRDs/PRVs) & FDC Inspection and Testing
10 Chapter 10: Fire Pump Systems & Drivers
10.1 Fire Pump Types (Horizontal Split Case, Vertical Turbine, End Suction) & System Arrangements 10.2 Fire Pump Drivers: Electric Motors, Diesel Engines & Controller Components 10.3 Pressure-Maintenance Pumps: Purpose, Capacity, and Coordinated Settings
11 Chapter 11: Fire Pump Inspection, Testing & Maintenance
11.1 Weekly Diesel (30-Minute) & Weekly/Monthly Electric (10-Minute) No-Flow (Churn) Tests 11.2 Annual Fire Pump Flow Test: Churn (0%), 100% Rated Flow & 150% Peak Flow 11.3 Pump Performance Evaluation: Net/Gross Curves and the Complete Acceptance Criteria 11.4 Diesel Support-System Maintenance and Electric-Pump Alternate Power
12 Chapter 12: Private Fire Service Mains & Hydrants
12.1 Underground Piping ITM & 5-Year Underground Flow Testing 12.2 Fire Hydrant Inspection, Lubrication & Annual Drainage Operational Tests 12.3 NFPA 291 Water Flow Testing: Layout, Pitot Readings & Flow Math 12.4 Hydrant Classification, Color Coding & Available Flow Extrapolation at 20 psi Residual
13 Chapter 13: Water Storage Tanks
13.1 Tank Types (Suction, Elevated, Pressure) & Component Overview 13.2 Inspection Frequencies: Water Level, Temperature (Min 40°F), Exterior & Interior 13.3 Tank Heating Systems, Low-Water Alarms, Vents, Overflow & Anti-Vortex Plates
14 Chapter 14: Internal Pipe Assessment & Obstruction Triggers
14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing 14.2 The Sixteen NFPA 25 (2023) Obstruction-Investigation Triggers 14.3 Five-Location Obstruction Examination, Evidence, and Required Follow-Up
15 Chapter 15: Flushing Methods, Contaminants & Deficiency Classification
15.1 Obstruction Materials: Corrosion, MIC Indicators, Scale, Ice, and Foreign Debris 15.2 Hydraulic Flushing: Program Scope, Velocity Calculations, and Completion Evidence 15.3 Specialist Cleaning Methods: Suitability, Safety Controls, and Restoration 15.4 Classifying Findings: Impairments vs. Critical Deficiencies vs. Noncritical Deficiencies
14.1 NFPA 25 Five-Year Internal Piping Assessment Procedures & Non-Destructive Testing
Key Takeaways Explain This Topic AI
Assess internal piping at least every five years or at the approved risk-analysis frequency; 14.2 exempts nonmetallic piping.
Apply the multiple-wet-system alternate assessment provisions with a traceable system list and expand when foreign material is found.
Use methods capable of finding the condition of interest; wall thickness alone cannot prove freedom from loose obstruction.
Potentially obstructive material requires investigation, and tubercules/slime require testing for MIC indications.
Last updated: October 2026
Assessment and investigation have different triggers
An internal piping assessment looks for foreign organic and inorganic material that could affect the system. An obstruction investigation is the more extensive response when specified conditions or findings indicate a potential obstruction. NFPA 25 (2023), 14.2 and 14.3, separates them. A five-year assessment is not automatically the same operation as every investigation, and a current assessment date does not cancel a new investigation trigger.
Section 14.2 requires assessment at least every five years unless an approved risk analysis establishes the applicable frequency. Nonmetallic piping is exempt from the 14.2 assessment requirement. That exemption does not mean foreign debris can be ignored or that a plastic system cannot be obstructed. Apply the actual investigation and condition requirements when evidence warrants them.
Plan a meaningful assessment
Review system drawings, type, age, materials, water source, prior findings, corrosion/leak history, and previous test results. Select locations and methods that provide useful evidence of internal condition. Annex A suggests approaches, including opening representative piping locations, but does not turn one suggested assessment method into the mandatory five-location investigation list. Avoid choosing only the most accessible clean section while excluding known troublesome areas.
Identify the system and locations in advance, coordinate access, and manage any interruption of protection. Prepare suitable tools, replacement gaskets/components, drainage, debris control, and documentation. Isolate and depressurize correctly before opening piping. A gauge at zero at one point does not prove every trapped section is relieved. Control stored energy and prevent debris entering the open system during the assessment.
Multiple wet systems
For buildings with multiple wet-pipe systems, apply the alternating-system assessment provision and assess the previously unexamined alternate systems at the next required interval. Keep an exact system list so the same convenient systems are not repeatedly selected while others are never examined. If foreign organic or inorganic material is found in any system in the building, the standard requires assessment of all systems under that provision.
Do not extend that alternate-system approach automatically to every dry or preaction system. System type and the wording of the provision matter. A record saying “half the building checked” is inadequate if it does not identify the systems, locations, findings, and basis. The owner needs enough information to schedule the next interval correctly.
Inspection methods and their limits
Direct observation through an appropriate opening can show loose debris, deposits, corrosion products, and the condition of the accessible surface. A borescope can extend the view into nearby piping, but bends, water, deposits, and limited reach can restrict coverage. Save images with system and location identifiers and an orientation or scale where useful. A photograph of clean pipe with no location cannot establish which system was assessed.
Nondestructive methods can provide useful evidence when appropriate to the task and permitted procedure. Ultrasonic thickness testing measures wall condition at examined locations; it does not automatically detect every loose obstruction or establish the absence of foreign material. Radiography and other methods have their own capability, access, and safety limitations. Select a method for the question being answered, not because “nondestructive” sounds like a universal substitute for internal observation.
- Method/evidence Useful information Important limit
- Direct internal view Visible debris and surface condition Only the accessible area is seen
- Internal video Images along the reachable path Visibility and range limit coverage
- Ultrasonic wall readings Local remaining wall thickness Does not prove all loose debris absent
- Prior flow trend Change in hydraulic behavior Does not identify every cause or location
- Interpret findings and act
If material with the potential to obstruct pipe or sprinklers is found, conduct the obstruction investigation under 14.3. Tubercules or slime found during assessment must be tested for indications of MIC. Color or odor is not a conclusive microbiological diagnosis. Arrange appropriate qualified analysis and follow the receiving laboratory's sampling instructions rather than using a universal field recipe.
There is no universal 1/16-inch deposit thickness, twenty-percent blockage allowance, or simple remaining-life formula that makes every system pass. The material's size, mobility, location, amount, and effect on pipe or sprinkler openings matter. A small loose object can plug an outlet even if its volume is minor compared with a large main. Record actual observations without declaring a hydraulic pass from appearance alone.
Close the work and preserve evidence
Control and account for tools, fragments, plugs, and temporary covers. Reassemble with appropriate components and procedures, complete required tests after the work, restore water/gas supplies and valves, and confirm monitoring and protection. Follow the impairment restoration process before removing tags. If assessment leads to further investigation, preserve that open action in the record.
Document date, system, interval basis, selected locations, method, images, findings, access limitations, laboratory work, and required follow-up. The report should distinguish assessed-and-clear portions from portions not examined. Keep the record available for the next assessment and for anyone reviewing the connected obstruction investigation.
Source checked October 19, 2026: NFPA 25 (2023), 14.2, 14.3, and Annex A explanatory material.