Study guide

11.3 Density/Area Design, Adjustments & Hose Streams

NICET Water-Based Systems Layout Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Open-Book References, PDF Navigation & Calculator Rules

2 Jobsite Safety

2.1 Jobsite Safety, PPE & Hazard Communication (SDS) 2.2 Ladder Safety (4:1), Scaffolding & OSHA 1926.501 Fall Protection

3 Contract Documents & Plan Reading

3.1 Architectural & Structural Drawings: Scales, Dimensions & Title Blocks 3.2 Specifications & MasterFormat Division 21 3.3 Bid Scope, Addenda, Change Orders & RFIs

4 Survey of Existing Conditions

4.1 Field Survey: Verifying As-Built Architecture 4.2 Obstructed vs Unobstructed Construction, Beams, Columns & Decks 4.3 Field Data: Pipe OD, Riser Gauges & Existing Sprinklers

5 Codes, Standards & Regulatory Hierarchy

5.1 NFPA 13, 13D, 13R & 291 Scopes 5.2 Coordinated Standards: NFPA 14, 20, 22, 24, 25 & IBC 5.3 AHJ Authority, Governing Editions, Listed vs Approved

6 Hazard Classification & System Types

6.1 Light Hazard & Ordinary Hazard Groups 1 & 2 6.2 Extra Hazard Groups 1 & 2 and Storage Overview 6.3 Wet, Dry, Preaction, Deluge & Water-Supply Types 6.4 Residential Layout Differences: NFPA 13D vs 13R

7 Sprinkler Characteristics & Ratings

7.1 Pendent, Upright, Sidewall & Concealed Orientations 7.2 RTI, Temperature Classifications & Bulb Colors 7.3 Extended Coverage, Residential, Quick-Response & ESFR

8 Sprinkler Spacing & Location

8.1 Maximum Protection Areas & Spacing by Hazard (NFPA 13 Tables 10.2.4.2.1) 8.2 Minimum Spacing, Wall Distance & the Small-Room Rule 8.3 Deflector Position in Unobstructed Construction 8.4 Deflector Position in Obstructed Construction & Sloped Ceilings

9 Obstructions to Discharge

9.1 Discharge Obstructions & the Three Times Rule 9.2 The Beam Rule & Deflectors Above Structural Members 9.3 Continuous Obstructions: Ducts, Cable Trays & Sprinklers Underneath

10 Piping, Hangers & Coordination Surveys

10.1 Pipe Materials, Hanger Spacing & Rod Sizing 10.2 Coordination Surveys with Other Trades

11 Hydraulics & NFPA 291 Flow Tests

11.1 Q = K√P and Standard K-Factors 11.2 Elevation Head, Minimum Pressure & Hazen-Williams 11.3 Density/Area Design, Adjustments & Hose Streams 11.4 NFPA 291 Hydrant Flow Tests, Pitot Math & Marking Colors

12 Submittal Packages & Working Plans

12.1 NFPA 13 Chapter 28 Working-Plan Content 12.2 Cut Sheets, Hydraulic Summaries & Approval Workflow

13 Project Correspondence & Closeout

13.1 AHJ Communications, Transmittals & RFI Tracking 13.2 Closeout: Material and Test Certificates & As-Builts

11.3 Density/Area Design, Adjustments & Hose Streams

Key Takeaways Explain This Topic AI

For new occupancy-hazard spray systems, NFPA 13 (2022) Table 19.2.3.1.1 is the single-point density/area table (the successor to older 19.3.3.1.1 curve picking).

Starting points: Light 0.10/1500; OH1 0.15/1500; OH2 0.20/1500; EH1 0.30/2500; EH2 0.40/2500 (gpm/ft² over ft²).

Sprinkler-system demand before hose is density × design area: Light 150 gpm, OH1 225, OH2 300, EH1 750, EH2 1000 gpm.

Table 19.2.3.1.2 combined hose-stream totals are 100 gpm (light), 250 gpm (ordinary), and 500 gpm (extra); durations are 30 min light, 60 or 90 ordinary, 90 or 120 extra.

Quick-response wet light/ordinary systems may reduce design area 40 percent at a 10 ft ceiling down to 25 percent at 20 ft (Figure 19.2.3.2.3.1) when every listed condition is met, never below five sprinklers.

Last updated: September 2026

Density × area is the sprinkler demand, not the water-supply demand

For new occupancy-hazard spray-sprinkler systems, NFPA 13 (2022) abandoned “any point on the curve.” Table 19.2.3.1.1 (the 2022 successor to the older Table 19.3.3.1.1 / curve figure) gives two points per hazard. The everyday point is the smaller area and higher density. The 0.07/3000, 0.12/3000, 0.17/3000, 0.28/3000, and 0.38/3000 alternates apply when 19.2.3.1.5 requires the 3,000 ft² operation for unsprinklered combustible concealed-space adjacency—not as a free designer preference. Figure 19.2.3.1.1 curves remain for evaluation or modification of existing systems .

Independent ExamFinch material uses the 2022 table as exam memory, not as a claim of AHJ adoption in every city. If a jurisdiction still enforces 2019, the curves can return; the NICET reference listed for this guide is 2022.

  • Hazard (Table 19.2.3.1.1) Density (gpm/ft²) Design area (ft²) Sprinkler demand before hose (gpm)
  • Light 0.10 1,500 0.10 × 1,500 = 150
  • Ordinary Group 1 0.15 1,500 0.15 × 1,500 = 225
  • Ordinary Group 2 0.20 1,500 0.20 × 1,500 = 300
  • Extra Group 1 0.30 2,500 0.30 × 2,500 = 750
  • Extra Group 2 0.40 2,500 0.40 × 2,500 = 1,000

That product is sprinklers only . Hose is a separate add.

Hose streams and duration (Table 19.2.3.1.2)

Table 19.2.3.1.2 still uses inside-hose choices of 0, 50, or 100 gpm and a total combined inside-plus-outside hose allowance of:

  • Light: 100 gpm , duration 30 minutes
  • Ordinary (Groups 1 and 2): 250 gpm , duration 60 or 90 minutes
  • Extra (Groups 1 and 2): 500 gpm , duration 90 or 120 minutes

The lower duration in each ordinary/extra pair is permitted when waterflow-alarm and supervisory devices are electrically supervised and monitored at an approved, constantly attended location ( 19.2.3.1.3 ). Inside hose is not an automatic extra 100 gpm on top of the total; the total is 100, 250, or 500 gpm. If inside hose stations take 100 gpm, the outside remainder is 0 (light), 150 (ordinary), or 400 (extra) unless the stem states a different permitted split. Hose is added at the supply connection (where the fire department actually takes water), not pushed through the remote sprinklers.

Worked water-supply totals (sprinkler product + combined hose):

  • Light: 150 + 100 = 250 gpm for 30 minutes
  • OH1: 225 + 250 = 475 gpm for 60 or 90 minutes
  • OH2: 300 + 250 = 550 gpm for 60 or 90 minutes
  • EH1: 750 + 500 = 1,250 gpm for 90 or 120 minutes
  • EH2: 1,000 + 500 = 1,500 gpm for 90 or 120 minutes

Storage ESFR and CMDA hose/duration rows live in Chapter 20 and are not these occupancy-hazard numbers. Do not import 250 gpm ESFR hose onto an extra-hazard office-shop calculation.

Quick-response area reduction — use the verified percents

19.2.3.2.3 / Figure 19.2.3.2.3.1 permit a design-area reduction without changing density when all of the following are true:

  • Wet pipe system
  • Light or ordinary hazard (not extra)
  • Maximum ceiling height 20 ft
  • No unprotected ceiling pockets exceeding 32 ft²
  • No unprotected areas above cloud ceilings as allowed by 9.2.7
  • The design area never uses fewer than five sprinklers ( 19.2.3.2.3.2 )

On the figure, percent reduction y is 40 percent at a 10 ft (and lower) ceiling, 25 percent at 20 ft, and zero above 20 ft. Between 10 ft and 20 ft the straight line is y = −1.5h + 55 (h in feet). At 15 ft: y = −1.5(15) + 55 = 32.5 percent .

Worked QR, 10 ft wet ordinary, starting area 1,500 ft²: 40 percent of 1,500 = 600. Remaining design area = 1,500 − 600 = 900 ft² . Density is unchanged. If the occupancy was OH2, sprinkler demand becomes 0.20 × 900 = 180 gpm before hose, not 300 gpm. Then add 250 gpm hose: 430 gpm at the supply. Quick-response sprinklers are not permitted for extra hazard or for occupancies with substantial flammable liquids or combustible dusts ( 19.2.3.2.2.2 ), so do not take a 40 percent extra-hazard cut.

Area increases that Level I must not forget

These increase area without changing density:

  • Sloped ceilings exceeding 2 in 12: +30 percent (19.2.3.2.4) for the listed spray/CMSA cases
  • Dry pipe and double-interlock preaction: +30 percent (19.2.3.2.5)

They compound on the originally selected area (19.2.3.2.8.1). Wet 1,500 ft² that is both dry-pipe and steeply sloped is not in one system at once, but a dry system on a steep slope is 1,500 × 1.3 × 1.3 = 2,535 ft² . Dry alone is 1,500 × 1.3 = 1,950 ft² .

High-temperature extra-hazard sprinklers may reduce area 25 percent , not below 2,000 ft² (19.2.3.2.6). K-11.2 or larger on extra-hazard Table 19.2.3.1.1 points may take the same 25 percent cut, not below 2,000 ft² (19.2.3.2.7). 2,500 × 0.75 = 1,875, which is below 2,000, so the floor is 2,000 ft² , not 1,875.

Unsprinklered combustible concealed-space rules in 19.2.3.1.5, if they apply, are imposed after the other modifications (19.2.3.2.8.2) and can drive the 3,000 ft² alternate densities in Table 19.2.3.1.1.

Minimum remote-area width along the branch lines is 1.2 √A (28.2.4.2). For A = 1,500, √1,500 ≈ 38.73, and 1.2 × 38.73 ≈ 46.5 ft . For the 900 ft² QR area, √900 = 30, and 1.2 × 30 = 36 ft . Level I should recognize the formula; laying out every head is later work.

Use this chapter with the rest of the Water-Based I study guide and check the arithmetic on practice items . The exam calculator will multiply 0.20 × 1,500 if you remember that those are the OH2 table numbers.