Study guide

11.2 Elevation Head, Minimum Pressure & Hazen-Williams

NICET Water-Based Systems Layout Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Open-Book References, PDF Navigation & Calculator Rules

2 Jobsite Safety

2.1 Jobsite Safety, PPE & Hazard Communication (SDS) 2.2 Ladder Safety (4:1), Scaffolding & OSHA 1926.501 Fall Protection

3 Contract Documents & Plan Reading

3.1 Architectural & Structural Drawings: Scales, Dimensions & Title Blocks 3.2 Specifications & MasterFormat Division 21 3.3 Bid Scope, Addenda, Change Orders & RFIs

4 Survey of Existing Conditions

4.1 Field Survey: Verifying As-Built Architecture 4.2 Obstructed vs Unobstructed Construction, Beams, Columns & Decks 4.3 Field Data: Pipe OD, Riser Gauges & Existing Sprinklers

5 Codes, Standards & Regulatory Hierarchy

5.1 NFPA 13, 13D, 13R & 291 Scopes 5.2 Coordinated Standards: NFPA 14, 20, 22, 24, 25 & IBC 5.3 AHJ Authority, Governing Editions, Listed vs Approved

6 Hazard Classification & System Types

6.1 Light Hazard & Ordinary Hazard Groups 1 & 2 6.2 Extra Hazard Groups 1 & 2 and Storage Overview 6.3 Wet, Dry, Preaction, Deluge & Water-Supply Types 6.4 Residential Layout Differences: NFPA 13D vs 13R

7 Sprinkler Characteristics & Ratings

7.1 Pendent, Upright, Sidewall & Concealed Orientations 7.2 RTI, Temperature Classifications & Bulb Colors 7.3 Extended Coverage, Residential, Quick-Response & ESFR

8 Sprinkler Spacing & Location

8.1 Maximum Protection Areas & Spacing by Hazard (NFPA 13 Tables 10.2.4.2.1) 8.2 Minimum Spacing, Wall Distance & the Small-Room Rule 8.3 Deflector Position in Unobstructed Construction 8.4 Deflector Position in Obstructed Construction & Sloped Ceilings

9 Obstructions to Discharge

9.1 Discharge Obstructions & the Three Times Rule 9.2 The Beam Rule & Deflectors Above Structural Members 9.3 Continuous Obstructions: Ducts, Cable Trays & Sprinklers Underneath

10 Piping, Hangers & Coordination Surveys

10.1 Pipe Materials, Hanger Spacing & Rod Sizing 10.2 Coordination Surveys with Other Trades

11 Hydraulics & NFPA 291 Flow Tests

11.1 Q = K√P and Standard K-Factors 11.2 Elevation Head, Minimum Pressure & Hazen-Williams 11.3 Density/Area Design, Adjustments & Hose Streams 11.4 NFPA 291 Hydrant Flow Tests, Pitot Math & Marking Colors

12 Submittal Packages & Working Plans

12.1 NFPA 13 Chapter 28 Working-Plan Content 12.2 Cut Sheets, Hydraulic Summaries & Approval Workflow

13 Project Correspondence & Closeout

13.1 AHJ Communications, Transmittals & RFI Tracking 13.2 Closeout: Material and Test Certificates & As-Builts

11.2 Elevation Head, Minimum Pressure & Hazen-Williams

Key Takeaways Explain This Topic AI

Elevation head is 0.433 psi per foot of water (inverse about 2.31 ft/psi); a sprinkler 20 ft above the gauge needs +8.66 psi.

Add elevation when the head is above the reference gauge; subtract only when the head is below that gauge.

Hazen-Williams friction rises with flow and pipe length and falls as C and internal diameter increase.

NFPA 13 (2022) Table 28.2.4.8.1: C = 120 wet steel (including deluge), C = 100 dry and preaction steel, C = 150 listed plastic (including CPVC) and copper/brass/stainless.

A smaller C is rougher pipe and demands more pressure for the same flow, length, and diameter; dry steel at C = 100 is about 1.40 times the friction of wet steel at C = 120.

Last updated: September 2026

Elevation is a pressure tax, not a flow formula

Section 11.1 found the pressure at the sprinkler . The water column between that sprinkler and the gauge you are reading still has to be paid. Independent ExamFinch material treats this as Level I algebra, not as a Level II branch-line worksheet.

NFPA 13 hydraulic work uses 0.433 psi per foot of elevation (some pocket cards round the twin value 0.434 psi/ft , which is 1 / 2.31). The inverse used on many exams is 2.31 ft of water = 1 psi . Memorize both directions so a stem can give feet or psi.

Worked elevation: a sprinkler is 20 ft above the riser gauge.

20 × 0.433 = 8.66 psi

Check with the inverse: 20 / 2.31 ≈ 8.66 psi. Same tax.

If that head already needs 12.8 psi from the 20 gpm / K-5.6 example in 11.1, the gauge 20 ft below must show at least 12.8 + 8.66 = 21.5 psi before you add pipe friction. Elevation does not change K and does not change Q by itself. It only changes the pressure you must have at the lower reference point.

Sign convention, in one sentence: heads above the gauge add psi to demand; heads below the gauge credit psi. A basement head 12 ft below a first-floor gauge is 12 × 0.433 = 5.20 psi of elevation credit at that head relative to the gauge. Do not credit elevation that the water cannot actually use (a closed valve, a dry pipe still full of air, or a stem that already gave you pressure at the elevation of the heads).

Another original check: a roof manifold 38 ft above the underground flange needs 38 × 0.433 = 16.5 psi of elevation before any fitting is entered on a calculation sheet. 38 / 2.31 ≈ 16.5 psi as well. If a choice says “38 psi because feet and psi are interchangeable,” that choice is padding.

Hazen-Williams: what Level I has to see without grinding a branch line

NFPA 13 pipe friction for water-based systems is Hazen-Williams . In U.S. units the loss rate is:

p (psi/ft) = 4.52 × Q^1.85 / (C^1.85 × d^4.87)

You do not need to hand-calc an entire remote branch on Level I. You do need to read the formula as four knobs:

Q up → friction up (steeply; the 1.85 exponent means a modest flow increase is a larger pressure increase).

Length up → total friction up (psi/ft times feet of equivalent pipe).

C up → friction down (smoother interior).

Diameter up → friction down (the 4.87 exponent makes diameter the strongest knob).

The exam-ready consequence: a smaller C demands more pressure for the same flow, length, and diameter. That is why dry-system steel and wet-system steel are not interchangeable on a calculation even when the pipe schedule looks identical.

Which C to pick (NFPA 13 2022 Table 28.2.4.8.1)

  • Pipe or tube C-value
  • Black or galvanized steel, wet systems including deluge 120
  • Black or galvanized steel, dry systems including preaction 100
  • Black or galvanized steel, dry/preaction with listed nitrogen (8.2.6.9) or the table’s vacuum provision 120
  • Listed plastic, including CPVC 150
  • Copper tube, brass, or stainless steel 150
  • Unlined cast or ductile iron 100
  • Cement-lined cast or ductile iron 140

The nitrogen path is not “any dry system with a bottle.” Section 8.2.6.9 requires a listed, permanently installed nitrogen generator that can hold at least 98 percent nitrogen throughout the system at a stated leakage rate, plus a means of verifying concentration. If those provisions are not in the stem, dry and preaction steel stays C = 100 .

An older field habit that “galvanized is always 120, even dry” is not how the 2022 table is written. Wet galvanized is 120; dry/preaction galvanized is 100 unless the nitrogen or vacuum row applies. Listed CPVC and copper are 150 in wet systems; do not assign them the steel dry-system 100.

How much more pressure does C = 100 really cost?

Hold Q, length, and diameter fixed and change only C. Friction scales as 1 / C^1.85, so the ratio of C-100 friction to C-120 friction is (120/100)^1.85 = 1.20^1.85 ≈ 1.40 . The dry steel system needs about 40 percent more friction pressure in that pipe than the same wet steel system. Level I should recognize the direction and the roughly 40 percent figure; Level II can grind the equivalent-length table.

Equivalent-length fitting multipliers in Table 28.2.3.2.1 are a different table. They start from C = 120 fitting lengths. A smoother pipe (C = 150) needs a longer equivalent length of that smooth pipe to represent the same fitting loss; a rougher pipe (C = 100) needs a shorter equivalent length. Do not invert those multipliers into a claim that C = 150 pipe has more friction than C = 100 pipe. Pipe friction still falls as C rises.

Minimum pressure at the supply is the stack, not one cell

At the reference gauge you are stacking:

  • Sprinkler pressure from Q = K√P (section 11.1),
  • Elevation at 0.433 psi/ft,
  • Friction from Hazen-Williams along the pipe and fittings,

Device losses the calculation sheet actually lists (alarm valve, backflow, etc.).

A stem that gives a 12.8 psi head, 20 ft of elevation, and “ignore friction for this item” wants 12.8 + 8.66 = 21.5 psi. A stem that only asks which C to type into software wants Table 28.2.4.8.1, not a made-up residential 130. Drill both skills on Water-Based I practice after you finish this study guide chapter .

Loading diagram... Elevation tax from the gauge up to the remote sprinkler