Study guide

11.1 Q = K√P and Standard K-Factors

NICET Water-Based Systems Layout Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Open-Book References, PDF Navigation & Calculator Rules

2 Jobsite Safety

2.1 Jobsite Safety, PPE & Hazard Communication (SDS) 2.2 Ladder Safety (4:1), Scaffolding & OSHA 1926.501 Fall Protection

3 Contract Documents & Plan Reading

3.1 Architectural & Structural Drawings: Scales, Dimensions & Title Blocks 3.2 Specifications & MasterFormat Division 21 3.3 Bid Scope, Addenda, Change Orders & RFIs

4 Survey of Existing Conditions

4.1 Field Survey: Verifying As-Built Architecture 4.2 Obstructed vs Unobstructed Construction, Beams, Columns & Decks 4.3 Field Data: Pipe OD, Riser Gauges & Existing Sprinklers

5 Codes, Standards & Regulatory Hierarchy

5.1 NFPA 13, 13D, 13R & 291 Scopes 5.2 Coordinated Standards: NFPA 14, 20, 22, 24, 25 & IBC 5.3 AHJ Authority, Governing Editions, Listed vs Approved

6 Hazard Classification & System Types

6.1 Light Hazard & Ordinary Hazard Groups 1 & 2 6.2 Extra Hazard Groups 1 & 2 and Storage Overview 6.3 Wet, Dry, Preaction, Deluge & Water-Supply Types 6.4 Residential Layout Differences: NFPA 13D vs 13R

7 Sprinkler Characteristics & Ratings

7.1 Pendent, Upright, Sidewall & Concealed Orientations 7.2 RTI, Temperature Classifications & Bulb Colors 7.3 Extended Coverage, Residential, Quick-Response & ESFR

8 Sprinkler Spacing & Location

8.1 Maximum Protection Areas & Spacing by Hazard (NFPA 13 Tables 10.2.4.2.1) 8.2 Minimum Spacing, Wall Distance & the Small-Room Rule 8.3 Deflector Position in Unobstructed Construction 8.4 Deflector Position in Obstructed Construction & Sloped Ceilings

9 Obstructions to Discharge

9.1 Discharge Obstructions & the Three Times Rule 9.2 The Beam Rule & Deflectors Above Structural Members 9.3 Continuous Obstructions: Ducts, Cable Trays & Sprinklers Underneath

10 Piping, Hangers & Coordination Surveys

10.1 Pipe Materials, Hanger Spacing & Rod Sizing 10.2 Coordination Surveys with Other Trades

11 Hydraulics & NFPA 291 Flow Tests

11.1 Q = K√P and Standard K-Factors 11.2 Elevation Head, Minimum Pressure & Hazen-Williams 11.3 Density/Area Design, Adjustments & Hose Streams 11.4 NFPA 291 Hydrant Flow Tests, Pitot Math & Marking Colors

12 Submittal Packages & Working Plans

12.1 NFPA 13 Chapter 28 Working-Plan Content 12.2 Cut Sheets, Hydraulic Summaries & Approval Workflow

13 Project Correspondence & Closeout

13.1 AHJ Communications, Transmittals & RFI Tracking 13.2 Closeout: Material and Test Certificates & As-Builts

11.1 Q = K√P and Standard K-Factors

Key Takeaways Explain This Topic AI

NFPA 13 hydraulic discharge is Q = K√P, rearranged as P = (Q/K)², with Q in gpm and P in psi at that sprinkler.

A standard 1/2 in orifice spray sprinkler is K-5.6; at 16 psi it discharges 5.6 × 4 = 22.4 gpm.

A K-5.6 sprinkler that must deliver 20 gpm needs P = (20/5.6)² ≈ 12.8 psi.

NFPA 13 (2022) 28.2.4.11 sets a 7 psi minimum operating pressure unless the listing is higher; at 7 psi a K-5.6 flows about 14.8 gpm.

Table 7.2.2.1 identification: K-2.8 (50%), K-4.2 (75%), K-5.6 (100%), K-8.0 (140%), K-11.2 (200%), K-14.0 (250%), K-16.8 (300%) of K-5.6 at the same pressure.

Last updated: September 2026

Why Level I still has to own Q = K√P

Independent ExamFinch material in this chapter helps learners study NICET Water-Based Systems Layout Level I tasks 1.5.2 Solve basic hydraulic equations and 1.5.3 Assist with flow tests . It is not an NFPA or NICET handbook, and it does not claim official approval from either organization. The exam references are NFPA 13 (2022) and NFPA 291 (2022) . The testing vendor supplies a built-in calculator . That calculator will multiply and take square roots; it will not remember which formula, which K-factor, or which C-value belongs in the stem. You still have to write Q = K√P from memory and keep the units straight.

Every listed sprinkler is identified by a K-factor , a discharge coefficient with U.S. units of gpm/psi^0.5. NFPA 13 hydraulic calculations use the same pair of equations at every head:

  • Q = K √P
  • P = (Q / K)²

Q is flow from that sprinkler in gallons per minute. P is the residual pressure at that sprinkler in pounds per square inch. √P is the square root of that pressure, not “P divided by two.” On the calculator, use the square-root key. Stems that look like simple arithmetic fail if you skip the root or square the wrong term.

Worked discharge: K-5.6 at 16 psi

The workhorse commercial spray sprinkler is K-5.6 , the 1/2 in orifice in NFPA 13 Table 7.2.2.1. A remote head is calculated at 16 psi.

Step 1: √16 = 4, because 4 × 4 = 16.

Step 2: Q = 5.6 × 4 = 22.4 gpm .

That 22.4 gpm is the flow at that one sprinkler at 16 psi. It is not the remote-area demand, not a hose-stream allowance, and not a hydrant pitot flow. If the stem later asks for eight such heads at the same pressure, you still start here, then add; you do not invent a new formula.

Worked pressure: K-5.6 must deliver 20 gpm

A light-hazard sprinkler covering 200 ft² at 0.10 gpm/ft² needs 20 gpm, because 0.10 × 200 = 20. The head is K-5.6. Invert the discharge equation.

Step 1: Q / K = 20 / 5.6 = 3.5714 (keep extra decimals until you square).

Step 2: P = (3.5714)² = 12.755 ≈ 12.8 psi .

12.8 psi is above the 7 psi minimum in NFPA 13 28.2.4.11, so density —not the floor pressure—governs this head. If the sprinkler’s listing specifies a higher minimum for the intended use, that listing governs instead of 7 psi.

The 7 psi floor is not a design density

Section 28.2.4.11 sets 7 psi (0.5 bar) as the minimum operating pressure for any sprinkler unless the listing is higher. At 7 psi:

  • √7 ≈ 2.646
  • Q = 5.6 × 2.646 ≈ 14.8 gpm

Now change the occupancy, not the K-factor. A K-5.6 covering 130 ft² of ordinary hazard Group 2 at 0.20 gpm/ft² needs 0.20 × 130 = 26 gpm .

P = (26 / 5.6)² = (4.6429)² ≈ 21.6 psi

Here density governs. You cannot “take 7 psi” and call the head finished. Calculate the pressure that produces the required flow, then confirm it is at least 7 psi or the listed minimum, whichever is greater.

Identify the other catalog K-factors

Table 7.2.2.1 is an identification table. The percentages are relative to a K-5.6 at the same pressure . Memorize the row, not a story about “all 1/2 in heads.”

  • Nominal K [gpm/psi^0.5] Metric K Percent of K-5.6 Nominal orifice Typical thread
  • 2.8 40 50% 3/8 in 1/2 in NPT
  • 4.2 60 75% 7/16 in 1/2 in NPT
  • 5.6 80 100% 1/2 in 1/2 in NPT
  • 8.0 115 140% 17/32 in 3/4 in or 1/2 in NPT
  • 11.2 160 200% 5/8 in 1/2 in or 3/4 in NPT
  • 14.0 200 250% 3/4 in 3/4 in NPT
  • 16.8 240 300% No nominal orifice in the annex size table 3/4 in NPT

Run the same algebra on other catalog K-factors with original pressures so the 16 psi example does not become the only number you can compute:

K-8.0 at 25 psi: √25 = 5; Q = 8.0 × 5 = 40 gpm .

K-11.2 at 9 psi: √9 = 3; Q = 11.2 × 3 = 33.6 gpm .

K-2.8 at 16 psi: Q = 2.8 × 4 = 11.2 gpm .

K-4.2 at 9 psi: Q = 4.2 × 3 = 12.6 gpm .

K-14.0 at 36 psi: √36 = 6; Q = 14.0 × 6 = 84 gpm .

K-16.8 at 25 psi: Q = 16.8 × 5 = 84 gpm .

K-5.6 must deliver 28 gpm: P = (28 / 5.6)² = 5² = 25 psi .

Because flow follows the square root of pressure, quadrupling pressure only doubles flow . K-5.6 at 16 psi is 22.4 gpm; at 64 psi (four times 16) it is 5.6 × 8 = 44.8 gpm. Doubling pressure from 16 psi to 32 psi multiplies flow only by √2 ≈ 1.41 (22.4 × 1.41 ≈ 31.6 gpm). If a stem claims that doubling pressure doubles flow, that choice is a trap.

NFPA 13 9.4.4 generally requires a minimum nominal K-5.6 unless a listed exception applies. K-2.8 and K-4.2 are permitted in light hazard when the system is hydraulically calculated and, for K-factors smaller than 5.6, on wet pipe—or under the exposure-protection and corrosion-resistant dry/preaction exceptions in 9.4.4.3 and 9.4.4.4. A listed strainer is required on the supply side of sprinklers smaller than K-2.8. CMSA and ESFR sprinklers start at K-11.2 . New systems must not use a K-factor larger than 5.6 on 1/2 in NPT (9.4.5). Do not hang a K-8.0 head on a K-5.6 calculation without re-running Q = K√P.

Keep a Water-Based I study map nearby and drill the same algebra on Water-Based I practice . The calculator on exam day only helps after you have already named K, Q, and P.

Loading diagram... Sprinkler discharge: pressure through a square root, then times K