Study guide

15.2 ANSI Z87.1 & FDA Safety Regulations

ABO NOCE National Opticianry Competency Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Ophthalmic Optics Terminology & Prescriptions

1.1 Ophthalmic Optics Terminology 1.2 Prescription Interpretation & Transposition 1.3 Measurement Systems & Conversions

2 Chapter 2: Lens Characteristics & Calculations

2.1 Lens Characteristics & Powers 2.2 Lens Formulas 2.3 Usable Accommodation & Range of Vision

3 Chapter 3: Prism, Decentration & Vertex Distance

Section 3.1: Prismatic Effects & Prentice's Rule Section 3.2: Decentration & Vertical Imbalance Section 3.3: Vertex Distance Compensation

4 Chapter 4: Ocular Anatomy & Physiology

4.1 Anatomy of the Eye 4.2 Physiology of Vision & Accommodation 4.3 Refractive Errors

5 Chapter 5: Ocular Pathology & Clinical Cues

5.1 Common Ocular Pathologies 5.2 Scope of Practice & Referral Cues 5.3 Visual Acuity & Testing Basics

6 Chapter 6: Frame Anatomy & Styles

6.1 Frame Materials 6.2 Frame Styles & Anatomy 6.3 Frame Selection for Prescriptions

7 Chapter 7: Lens Materials & Designs

7.1 Lens Materials Comparison 7.2 Multifocal & Trifocal Lenses 7.3 Aspheric & Digitally Surfaced Lenses

8 Chapter 8: Progressive Lenses & Coatings

Section 8.1: Progressive Addition Lenses Section 8.2: Lens Coatings Section 8.3: Lens Tints & Photochromics

9 Chapter 9: Specialty Products & Low Vision

9.1 Low Vision Aids 9.2 Safety Eyewear 9.3 Sports & Occupational Eyewear 9.4 Preassembled Eyewear & OTC Readers

10 Chapter 10: Manual Lensmetry

10.1 Lensmeter Operation & Verification 10.2 Verifying Cylinder Axis & Power 10.3 Measuring Prism on the Lensmeter

11 Chapter 11: Optical Measurement Instruments

11.1 Automated Lensmeters & Calibration 11.2 Lens Clock & Base Curves 11.3 Calipers, Thickness Gauges & PD Tools

12 Chapter 12: Dispensing Tools & Vertex Measurement

12.1 Dispensing Hand Tools 12.2 Distometer & Vertex Distance 12.3 Instrument Safety & Calibration

13 Chapter 13: Patient Measurements & History

13.1 Patient History & Needs Analysis 13.2 Measuring Pupillary Distance 13.3 Measuring Segment Height

14 Chapter 14: Frame Fitting & Troubleshooting

Section 14.1: Nosepad & Bridge Adjustments Section 14.2: Temple & Ear Adjustments Section 14.3: Troubleshooting Visual Complaints

15 Chapter 15: Laws, Regulations & Standards

15.1 ANSI Z80.1 Prescription Tolerances 15.2 ANSI Z87.1 & FDA Safety Regulations 15.3 FTC Eyeglass Rule & Professional Ethics 15.4 Universal Precautions, Coding, Insurance & FCLCA

15.2 ANSI Z87.1 & FDA Safety Regulations

Key Takeaways Explain This Topic AI

ANSI/ISEA Z87.1-2020 governs occupational eye and face protection, categorized into basic impact and high impact standards, enforced by OSHA in workplaces.

Prescription basic impact safety lenses require a 3.0 mm minimum thickness (2.5 mm if power > +3.00 D) and must pass a 1-inch steel ball drop test.

Prescription high-impact safety lenses require a 2.0 mm minimum thickness, marked with a '+' on the lens, and must pass high-mass and high-velocity projectile tests.

FDA regulation 21 CFR 801.410 mandates that all dress (everyday) eyewear be impact-resistant, verified using a 5/8-inch steel ball dropped from 50 inches.

FDA testing protocol requires 100% individual testing for prescription glass lenses, whereas batch testing is permitted for plastic lenses like CR-39.

Last updated: July 2026

ANSI Z87.1 & FDA Safety Regulations

Ophthalmic dispensing involves not only maximizing visual acuity but also protecting the patient's eyes from environmental hazards. In the United States, protective eyewear standards and regulations are established by two primary entities: the American National Standards Institute (ANSI), which publishes the voluntary consensus standard ANSI/ISEA Z87.1-2020: Occupational and Educational Personal Eye and Face Protection Devices , and the federal Food and Drug Administration (FDA), which regulates everyday dress eyewear under 21 CFR 801.410 . The Occupational Safety and Health Administration (OSHA) enforces ANSI Z87.1 compliance in the workplace.

ANSI Z87.1-2020 Safety Eyewear Standards

The ANSI Z87.1 standard covers eye protection devices used in industrial, educational, and medical settings. It separates protectors into two performance categories: "basic impact" and "high impact." Lenses and frames must undergo rigorous testing to achieve these ratings.

Basic Impact Lenses

Basic impact safety lenses are designed to protect against low-velocity hazards, such as dust, wood shavings, or minor hand-tool debris.

Minimum Thickness : Prescription basic impact safety lenses must have a minimum center thickness of 3.0 mm . An exception is permitted: if the lens power in the most plus meridian of the distance portion is greater than +3.00 D , the minimum thickness can be reduced to 2.5 mm .

The Z87 Basic Impact Test : The lens is mounted in a standard test holder and subjected to a drop-ball test. A 1-inch steel ball (weighing approximately 2.4 ounces) is dropped from a height of 50 inches onto the center of the lens. The lens must not crack, chip, fracture, or dislodge from the holder.

High Impact Lenses

High impact safety lenses are designed to protect against high-velocity hazards, such as flying metal fragments, grinding sparks, or impact from power tools. High-impact lenses are typically fabricated from impact-resistant polymers such as polycarbonate or Trivex .

Minimum Thickness : Prescription high-impact lenses must maintain a minimum thickness of 2.0 mm at their thinnest point, regardless of lens material or dioptric power. There is no power-based thickness exemption.

The High-Mass Test : A heavy, pointed projectile weighing 17.6 ounces (1.1 pounds) is dropped through a tube from a height of 50 inches onto the lens mounted in a frame. The lens must not fracture or detach from the frame.

The High-Velocity Test : A 1/4-inch steel ball is propelled at the lens at a speed of 150 feet per second (102 miles per hour) for spectacles, or 250 feet per second for face shields. The test is repeated at multiple angles. The lens must not break, chip, or be pushed out of the frame.

Frame Markings and Side Protection

Safety Frame Markings : Safety frames must meet stringent structural requirements. Prescription safety frames must be marked with Z87-2 on the frame front and both temples to indicate they are rated for prescription use. If the frame is rated for high impact, it is marked with Z87-2+ .

Safety Lens Markings : Lenses must also be permanently marked. High-impact lenses are etched with the manufacturer's logo and a "+" sign (e.g., "O+"). Basic impact lenses are etched with only the manufacturer's logo.

Side Shields : To protect the eyes from lateral hazards, safety glasses must have side shields. The Z87.1 standard allows side shields to be either permanent (built-in) or removable. If removable side shields are used, they must be specifically tested and certified for use with that exact frame model.

FDA Regulation 21 CFR 801.410: Dress Eyewear

The FDA regulates everyday, fashion, and sun eyewear under federal regulation 21 CFR 801.410 . The FDA's mandate is to ensure that all spectacles sold to the general public possess a baseline level of impact resistance.

The FDA Drop-Ball Test Protocol

Unlike the Z87.1 safety standards, the FDA does not specify a minimum thickness for dress lenses. It is a performance-based regulation. A lens of any thickness is compliant, provided it can pass the referee test:

Test Setup : A 5/8-inch steel ball weighing approximately 0.56 ounces is dropped from a height of 50 inches onto the horizontal upper surface of the lens at its geometric center.

Pass/Fail Criteria : A lens fails the test if it fractures (splits into two or more pieces) or if any lens material visible to the naked eye becomes detached from the ocular (inner) surface.

Testing Frequency: Glass vs. Plastic

The FDA distinguishes between lens materials regarding how frequently they must be tested:

Prescription Glass Lenses : Glass is highly brittle. To ensure safety, 100% of prescription glass lenses must be individually drop-ball tested after being finished, surfaced, and tempered (either by heat-treating or chemical-tempering). The optician or laboratory must document this individual test.

Plastic Lenses (CR-39, Polycarbonate, Trivex) : Because plastic materials are inherently flexible and impact-resistant, the FDA permits statistical batch testing . The manufacturer or laboratory must test a statistically representative sample from each production lot.

FDA Testing Exemptions

Certain specialized lens designs are exempt from the drop-ball test because the test itself would damage the lens or because the lens cannot be manufactured to withstand the impact without destroying its utility. These lenses must still be made as impact-resistant as possible, but do not undergo testing:

  • Raised-segment multifocal lenses (e.g., executive bifocals)
  • Prism segment multifocal lenses
  • Slab-off prism lenses
  • Lenticular lenses (high-plus cataract lenses)
  • Laminated glass/plastic lenses
  • Custom-made prescription lenses of unique or delicate design
  • Warning Labels and Record Keeping

The FDA requires manufacturers, importers, and dispensers to maintain records of impact-resistance compliance (such as laboratory invoices and batch testing logs) for at least 3 years from the date of distribution. Furthermore, when dispensing glass lenses, opticians must ethically inform patients that while the lenses pass the FDA impact test, they are not "shatterproof" or "unbreakable."

Regulation Comparison Table

Specification FDA Dress Eyewear (21 CFR 801.410) ANSI Z87.1 Safety (Basic Impact) ANSI Z87.1 Safety (High Impact)

  • Minimum Thickness None specified (performance-based) 3.0 mm (2.5 mm if > +3.00 D) 2.0 mm (no power exception)
  • Drop Ball size 5/8-inch steel ball (0.56 oz) 1-inch steel ball (2.4 oz) High-mass & High-velocity tests
  • Drop Height 50 inches 50 inches 50 inches (high-mass) / Propelled (high-velocity)

Testing Protocol Glass: 100% individual. Plastic: Batch testing. Sample/batch testing for industrial lines Sample/batch testing for industrial lines

Markings Required None required on lens or frame Z87 or Z87-2 on frame/lens Z87+ or Z87-2+ on frame/lens

Workplace Legality Not legal for hazardous areas Legal for low-impact work environments Required for high-impact work environments