Study guide
10.2 Verifying Cylinder Axis & Power
ABO NOCE National Opticianry Competency Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Ophthalmic Optics Terminology & Prescriptions
1.1 Ophthalmic Optics Terminology 1.2 Prescription Interpretation & Transposition 1.3 Measurement Systems & Conversions
2 Chapter 2: Lens Characteristics & Calculations
2.1 Lens Characteristics & Powers 2.2 Lens Formulas 2.3 Usable Accommodation & Range of Vision
3 Chapter 3: Prism, Decentration & Vertex Distance
Section 3.1: Prismatic Effects & Prentice's Rule Section 3.2: Decentration & Vertical Imbalance Section 3.3: Vertex Distance Compensation
4 Chapter 4: Ocular Anatomy & Physiology
4.1 Anatomy of the Eye 4.2 Physiology of Vision & Accommodation 4.3 Refractive Errors
5 Chapter 5: Ocular Pathology & Clinical Cues
5.1 Common Ocular Pathologies 5.2 Scope of Practice & Referral Cues 5.3 Visual Acuity & Testing Basics
6 Chapter 6: Frame Anatomy & Styles
6.1 Frame Materials 6.2 Frame Styles & Anatomy 6.3 Frame Selection for Prescriptions
7 Chapter 7: Lens Materials & Designs
7.1 Lens Materials Comparison 7.2 Multifocal & Trifocal Lenses 7.3 Aspheric & Digitally Surfaced Lenses
8 Chapter 8: Progressive Lenses & Coatings
Section 8.1: Progressive Addition Lenses Section 8.2: Lens Coatings Section 8.3: Lens Tints & Photochromics
9 Chapter 9: Specialty Products & Low Vision
9.1 Low Vision Aids 9.2 Safety Eyewear 9.3 Sports & Occupational Eyewear 9.4 Preassembled Eyewear & OTC Readers
10 Chapter 10: Manual Lensmetry
10.1 Lensmeter Operation & Verification 10.2 Verifying Cylinder Axis & Power 10.3 Measuring Prism on the Lensmeter
11 Chapter 11: Optical Measurement Instruments
11.1 Automated Lensmeters & Calibration 11.2 Lens Clock & Base Curves 11.3 Calipers, Thickness Gauges & PD Tools
12 Chapter 12: Dispensing Tools & Vertex Measurement
12.1 Dispensing Hand Tools 12.2 Distometer & Vertex Distance 12.3 Instrument Safety & Calibration
13 Chapter 13: Patient Measurements & History
13.1 Patient History & Needs Analysis 13.2 Measuring Pupillary Distance 13.3 Measuring Segment Height
14 Chapter 14: Frame Fitting & Troubleshooting
Section 14.1: Nosepad & Bridge Adjustments Section 14.2: Temple & Ear Adjustments Section 14.3: Troubleshooting Visual Complaints
15 Chapter 15: Laws, Regulations & Standards
15.1 ANSI Z80.1 Prescription Tolerances 15.2 ANSI Z87.1 & FDA Safety Regulations 15.3 FTC Eyeglass Rule & Professional Ethics 15.4 Universal Precautions, Coding, Insurance & FCLCA
10.2 Verifying Cylinder Axis & Power
Key Takeaways Explain This Topic AI
Spherocylindrical lenses correct astigmatism and have two principal meridians of power that are 90 degrees apart.
A broken or stepped target appearance indicates that the target is misaligned with the principal meridians of the lens.
Neutralization in minus cylinder form requires focusing the thin (sphere) lines first and then turning the power wheel in the minus direction to focus the thick (cylinder) lines.
The cylinder power is calculated as the algebraic difference between the second power wheel reading and the first reading.
The cylinder axis is read directly from the axis wheel scale once the target lines are aligned and continuous.
Last updated: July 2026
Understanding Spherocylindrical Optics
A spherocylindrical lens is used to correct astigmatism, a condition where the eye's cornea or crystalline lens has unequal curvature in different meridians. Consequently, a spherocylindrical lens has two principal meridians of refractive power: the sphere meridian (which represents the baseline spherical correction) and the cylinder meridian (which represents the maximum difference in power from the sphere meridian). These two meridians are always perpendicular (90 degrees apart) to each other.
Because the power varies across the lens, a manual lensmeter will not focus both sets of target lines simultaneously. Instead, the thin (sphere) lines will focus at one setting on the power wheel, and the thick (cylinder) lines will focus at a different setting. The difference between these two readings represents the cylinder power , while the orientation of the meridians is determined by the axis wheel positioning .
The Spherocylindrical Target Appearance
When a spherocylindrical lens is placed in a manual lensmeter, the target lines will initially appear broken, distorted, or "stepped." This occurs because the target lines are not aligned with the principal meridians of the lens. The optician must perform cylinder line alignment by rotating the axis wheel until the target lines form continuous, straight, and unbroken lines.
Thin lines (sphere lines) represent the first principal meridian. When they are aligned and in focus, they appear as three continuous parallel lines.
Thick lines (cylinder lines) represent the second principal meridian. When they are in focus, they appear as three continuous parallel lines perpendicular to the thin lines.
If the lines are aligned but out of focus, they will appear blurry but straight. If they are misaligned, they will appear broken or stepped even when they are in focus.
Step-by-Step Neutralization in Minus Cylinder Form
In ophthalmic dispensing, prescriptions are standardly written in minus cylinder form (where the cylinder value is negative). To neutralize a lens in minus cylinder form, the optician must follow a specific sequence. This ensures that the sphere power is measured first and the cylinder power is subtracted from it, yielding a negative cylinder value.
The step-by-step procedure is:
Place and Align the Lens : Place the spectacles on the lens table with the back surface against the lens stop. Clamp the lens securely.
Locate the Sphere Meridian : Turn the power wheel to a high plus setting (blurring the target). Slowly rotate the power wheel in the minus direction (reducing plus power or increasing minus power) until one set of target lines begins to clear.
Perform Axis Alignment : If the lines appear broken or stepped, rotate the axis wheel until the lines align into continuous, unbroken lines. Continue adjusting the power wheel in the minus direction until these lines are in sharp, crisp focus.
Verify Sphere Line Focus : To ensure the neutralization is in minus cylinder form, the lines that focus first (at the more positive/less negative setting) must be the thin lines (sphere lines). If the thick lines focus first, rotate the axis wheel by 90 degrees and refocus the thin lines.
Record the Sphere Power : Look at the power wheel scale. This first reading is the sphere power .
Locate the Cylinder Meridian : Continue turning the power wheel in the minus direction (more negative/less positive). The thin lines will become blurry, and the thick lines (cylinder lines) will begin to clear. Adjust the power wheel until the thick lines are in sharp, crisp focus.
Record the Second Reading : Look at the power wheel scale. This is the second reading.
Calculate the Cylinder Power : The cylinder power is the power wheel reading difference between the second reading and the first reading (Second Reading - First Reading). Because you moved the wheel in the minus direction, the second reading will always be more negative than the first, resulting in a negative cylinder power.
Read the Axis : Look at the axis wheel. The number indicated on the drum is the cylinder axis .
Neutralization Example Calculations
To illustrate this process, consider the following three worked examples of spherocylindrical neutralization in minus cylinder form:
- Example 1: High Plus Prescription
- First Reading (Thin Lines focus) : +4.50 D
- Second Reading (Thick Lines focus) : +2.25 D
- Axis Wheel Reading : 090°
Calculation : The sphere power is +4.50 D. The cylinder power is the difference: (+2.25 D) - (+4.50 D) = -2.25 D.
- Resulting Rx : +4.50 -2.25 x 090
- Example 2: Mixed Astigmatism
- First Reading (Thin Lines focus) : +1.50 D
- Second Reading (Thick Lines focus) : -1.00 D
- Axis Wheel Reading : 180°
Calculation : The sphere power is +1.50 D. The cylinder power is the difference: (-1.00 D) - (+1.50 D) = -2.50 D.
- Resulting Rx : +1.50 -2.50 x 180
- Example 3: High Minus Prescription
- First Reading (Thin Lines focus) : -2.00 D
- Second Reading (Thick Lines focus) : -5.50 D
- Axis Wheel Reading : 045°
Calculation : The sphere power is -2.00 D. The cylinder power is the difference: (-5.50 D) - (-2.00 D) = -3.50 D.
Resulting Rx : -2.00 -3.50 x 045
- Parameter Example 1 Example 2 Example 3
- First Focus (Thin) +4.50 D +1.50 D -2.00 D
- Second Focus (Thick) +2.25 D -1.00 D -5.50 D
- Axis Wheel 090° 180° 045°
- Sphere Power +4.50 D +1.50 D -2.00 D
- Cylinder Power -2.25 D -2.50 D -3.50 D
- Final Rx (Minus Cyl) +4.50 -2.25 x 090 +1.50 -2.50 x 180 -2.00 -3.50 x 045
- Common Errors in Cylinder Verification
A common mistake is neutralizing the lens in plus cylinder form . If the optician focuses the thick lines first (at a more positive power) and then turns the wheel in the minus direction to focus the thin lines, the cylinder power calculation will yield a positive value. While mathematically equivalent after transposition, clinical standards require documenting prescriptions in minus cylinder form. If this occurs, the optician should transpose the result: add the sphere and cylinder powers to find the new sphere power, change the sign of the cylinder to negative, and rotate the axis by 90 degrees.