Study guide

9.1 Map Types, Plan Sheets, Title Blocks, and Revision Blocks

NSPS Certified Survey Technician Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Survey Types & Historical Development

1.1 CST Certification & Survey Licensing Distinction 1.2 Boundary, Cadastral, and Land Surveys 1.3 Topographic, Hydrographic, and Route Surveys 1.4 Construction, As-Built, and Industrial Alignment Surveys 1.5 Historical Surveying Units, Instruments, and Practices

2 Chapter 2: Tripods, Instruments & Field Setup

2.1 Tripod Setup, Centering, Plumbing, and Optical Plummets 2.2 Instrument Leveling, Bubble Vials, and Electronic Tilt Sensors 2.3 Equipment Care, Cleaning, Storage, and Transport Safety

3 Chapter 3: Taping, Leveling & Distance Measurement

3.1 Steel Taping, Tension, Temperature, and Slope Corrections 3.2 Differential Leveling Equipment, Rods, Targets, and Rod Reading 3.3 Total Station Operations, Prism Constants, and EDM Basics 3.4 Data Collectors, Field Software Jobs, and File Management

4 Chapter 4: Field Operations, Notes & Communication

4.1 Field Note Bookkeeping, Standard Layout, and Hand-Drawn Sketches 4.2 Field Radio Procedures, Hand Signals, and Crew Communications 4.3 Line Clearing, Brush Removal, and Obstacle Clearance Safety 4.4 Setting Field Monuments, Rebar, Caps, Stakes, and Tacks

5 Chapter 5: Survey Control Networks & Monuments

5.1 Horizontal & Vertical Control Principles and Monument Types 5.2 Benchmarks, Datums (NAVD88, NAD83), and Field Verification Checks

6 Chapter 6: Basic Surveying Mathematics & Unit Conversions

6.1 Linear & Angular Unit Conversions (Feet, Chains, Links, Acres, DMS, Radians) 6.2 Right Triangle Trigonometry and Geometry in Surveying 6.3 Approved Calculator Operations & Memory Management (Casio fx-115/991, HP 35s, TI-36X)

7 Chapter 7: Leveling & Distance Computations

7.1 Differential Leveling Computations (HI, Backsight, Foresight, Page Checks) 7.2 Slope Distance Reductions and Horizontal/Vertical Components 7.3 Elevation, Grade Percent, and Stationing Calculations

8 Chapter 8: Coordinate Geometry & Area Calculations

8.1 Bearings, Azimuths, and Angular Conversions 8.2 Rectangular Coordinates (Northings/Eastings) and Departure/Latitude Basics 8.3 Area Calculations (Triangles, Trapezoids, Rectangles, and Simple Polygons)

9 Chapter 9: Plan Reading, Scale & Topography

9.1 Map Types, Plan Sheets, Title Blocks, and Revision Blocks 9.2 Scale Conversions, Graphical Scales, and Dimension Verification 9.3 Contour Lines, Spot Elevations, Interpolation, and Profiles

10 Chapter 10: CAD & Drafting Conventions

10.1 CAD Layers, Line Types, Symbols, and Legend Standards 10.2 Drafting Standards, Text Styles, and Title Block Preparation 10.3 Coordinate Systems, Grid vs. Ground, and Plan Orientation

11 Chapter 11: Field Safety, Hazards & First Aid

11.1 Personal Protective Equipment (PPE) & Construction Site Safety 11.2 Traffic Control, Flaggers, and Roadway Work Zone Safety (MUTCD) 11.3 Environmental Hazards: Heat Stress, Cold Exposure, Poisonous Plants, and Animals 11.4 Electrical Hazards, Overhead Power Lines, and Excavation Safety 11.5 Basic First Aid, CPR Principles, and Emergency Response Protocols

9.1 Map Types, Plan Sheets, Title Blocks, and Revision Blocks

Key Takeaways Explain This Topic AI

Boundary plats detail legal property lines, corners, bearings, distances, and PLS certification, whereas topographic maps focus on existing ground elevations, contours, and physical features.

Title blocks must contain project identification, site location, firm license details, scale, drawing date, sheet numbering (e.g., Sheet 3 of 10), and the Professional Land Surveyor (PLS) seal and signature.

Revision blocks (marked with delta symbols Δ) record all post-issuance drawing modifications, dates, descriptions, and approval initials for legal audit tracking.

Profile sheets depict vertical longitudinal sections along alignment stationing with exaggerated vertical scales, while cross-section sheets display transverse slices perpendicular to centerline.

Survey drawings utilize three north references: True (Geodetic) North (geographic pole), Magnetic North (compass needle), and Grid North (parallel to plane coordinate central meridian).

Last updated: July 2026

9.1 Map Types, Plan Sheets, Title Blocks, and Revision Blocks

Quick Answer: Survey plan sets comprise specialized drawing types (boundary plats, topographic maps, site plans, grading plans, utility plans, profile sheets, and cross-sections) engineered to convey spatial, legal, and physical construction data. Every professional drawing is anchored by a standardized title block containing project governance data and a Professional Land Surveyor (PLS) seal , supported by a revision block to track design updates, and oriented by defined north arrows (True, Magnetic, or Grid North).

In field surveying and civil engineering, plan sheets serve as the primary legal, technical, and graphical medium for communicating land measurements, proposed improvements, and existing site conditions. Survey technicians must quickly navigate diverse plan types, decode title and revision blocks, and interpret orientation references to perform accurate field stakeout, boundary line verification, and layout checks.

Primary Types of Survey Plans and Drawings

Different phases of surveying, land development, and civil infrastructure construction require dedicated plan drawing formats. Each map type emphasizes specific spatial elements:

Boundary Plat (Boundary Survey): A legal instrument depicting property boundaries, physical boundary monuments found or set (e.g., rebar, iron pipes, stone markers), line bearings, curve data, parcel acreage/square footage, adjoining land owners ( adjoiners ), rights-of-way, and dedicated easements. It features an official surveyor's certification, signature, and state registration seal.

Topographic Map: A detailed spatial drawing representing physical ground features, natural terrain (lakes, streams, tree lines), man-made structures (buildings, fences, roads), and vertical relief using contour lines and spot elevations .

Site Plan (Development Plan): An architectural and engineering drawing overlaying proposed land improvements onto existing site geometry. It details proposed building footprints, parking structures, access driveways, landscaping, zoning setback lines, and property boundary lines.

Grading Plan: Details proposed site earthwork, ground re-shaping, proposed finish contours, cut and fill boundaries, slope ratios (e.g., 3 : 1 3:1 3 : 1 horizontal-to-vertical), drainage swales, retention/detention basins, and spot elevations for finish floor (FF) slabs, top of curb (TC), and flowlines (FL).

Utility Plan: Maps underground and overhead public and private utilities, including water mains, sanitary sewer lines, storm drainage systems, natural gas mains, electrical conduits, and telecommunication lines. Callouts include pipe diameters, materials, slope percentages, invert elevations (IE), and manhole rim elevations.

Profile Sheet: Displays a vertical longitudinal cut view along an alignment centerline (such as a highway, sewer main, or rail corridor). The horizontal X-axis represents alignment stationing (e.g., Sta 10 + 00 10+00 10 + 00 ), while the vertical Y-axis represents ground and pipe elevations . Profile views typically use an exaggerated vertical scale (e.g., 1 ′ ′ = 50 ′ 1'' = 50' 1 ′′ = 5 0 ′ horizontal, 1 ′ ′ = 5 ′ 1'' = 5' 1 ′′ = 5 ′ vertical) to make vertical terrain changes visually clear.

Cross-Section Sheet: Displays vertical transverse slices perpendicular to an alignment centerline at designated station intervals (e.g., every 50 ft or 100 ft). Cross-sections compare existing ground surface lines against proposed roadway templates, highlighting cut/fill earthwork areas, ditch slopes, and structural pavement layers.

Summary of Standard Survey Drawing Types

Drawing Type Primary Focus & Purpose Key Elements Shown Typical Scale Range

Boundary Plat Legal land ownership & parcel boundaries Bearings, distances, monuments, easements, PLS seal 1 ′ ′ = 20 ′ 1'' = 20' 1 ′′ = 2 0 ′ to 1 ′ ′ = 100 ′ 1'' = 100' 1 ′′ = 10 0 ′

Topographic Map Existing vertical & horizontal terrain features Contours, spot elevations, structures, water bodies 1 ′ ′ = 10 ′ 1'' = 10' 1 ′′ = 1 0 ′ to 1 ′ ′ = 200 ′ 1'' = 200' 1 ′′ = 20 0 ′

Site Plan Proposed land development & site layout Building footprints, setbacks, parking, driveways 1 ′ ′ = 20 ′ 1'' = 20' 1 ′′ = 2 0 ′ to 1 ′ ′ = 50 ′ 1'' = 50' 1 ′′ = 5 0 ′

Grading Plan Earthwork modifications & site drainage Finish contours, cut/fill limits, FF & TC elevations 1 ′ ′ = 20 ′ 1'' = 20' 1 ′′ = 2 0 ′ to 1 ′ ′ = 50 ′ 1'' = 50' 1 ′′ = 5 0 ′

Utility Plan Subsurface & overhead infrastructure systems Pipes, valves, hydrants, inverts (IE), manhole rims 1 ′ ′ = 20 ′ 1'' = 20' 1 ′′ = 2 0 ′ to 1 ′ ′ = 60 ′ 1'' = 60' 1 ′′ = 6 0 ′

Profile Sheet Longitudinal elevation view along centerline Alignment stationing, existing vs finish grade H: 1 ′ ′ = 50 ′ 1''=50' 1 ′′ = 5 0 ′ , V: 1 ′ ′ = 5 ′ 1''=5' 1 ′′ = 5 ′

Cross-Section Sheet Transverse slice perpendicular to centerline Roadway template, ditch slopes, cut/fill areas 1 ′ ′ = 10 ′ 1'' = 10' 1 ′′ = 1 0 ′ or 1 ′ ′ = 20 ′ 1'' = 20' 1 ′′ = 2 0 ′

Title Block Elements and Governance Standards

The title block is the administrative and legal control center of a plan sheet, typically positioned in the lower-right corner or along the right-hand margin of standard CAD drawing sheets (such as ANSI D 24 ′ ′ × 36 ′ ′ 24'' \times 36'' 2 4 ′′ × 3 6 ′′ or ARCH D sheets). It provides mandatory metadata required for regulatory approval and construction management:

Project Title and Subtitle: Identifies the formal project name, phase number, subdivision name, or municipal infrastructure contract designation.

Site Location: Details street address, municipality, county, state, and legal section/township/range or subdivision lot/block descriptors.

Client / Owner Information: Specifies the land owner, public agency, or private developer commissioning the survey.

Surveying / Engineering Firm Information: Lists the professional firm name, office address, phone number, and corporate business license registration number.

Drawing Scale: States both the written numerical scale (e.g., 1 ′ ′ = 40 ′ 1'' = 40' 1 ′′ = 4 0 ′ ) and includes a printed graphic bar scale for direct measurement.

Date of Fieldwork and Drafting: Displays the date field survey measurements were completed and the date of drawing finalization.

Sheet Index Number and Title: Indicates the sheet sequence (e.g., Sheet 4 of 12) and sheet classification identifier (e.g., C-101 for Civil Site, C-200 for Grading, C-300 for Utilities).

Professional Land Surveyor (PLS) Seal & Signature: The official legal certification stamp, handwritten or secure digital signature, license number, and signing date of the licensed Professional Land Surveyor. Without a valid PLS seal and signature, a boundary plat or survey drawing carries no legal authority for recording or construction.

Revision Block Conventions and Audit Trails

Plans undergo frequent modifications during design review, permitting, addenda issuance, and construction field adjustments. The revision block —located directly above or adjacent to the main title block—maintains a strict legal and administrative paper trail.

Standard revision block entries include four essential columns:

Revision Symbol / Delta Number: A triangular delta symbol containing a sequential number ( Δ 1 , Δ 2 , Δ 3 \,\Delta_1, \Delta_2, \Delta_3\, Δ 1 ​ , Δ 2 ​ , Δ 3 ​ ) corresponding to matching delta callout tags drawn on the plan sheet around the modified region.

Description of Revision: A concise explanation of the change (e.g., "Revised storm sewer invert at Sta 12+50 per City comments").

Revision Date: The official calendar date the change was incorporated into the drawing set.

Approval Initials: The initials of the draftsman who performed the edit and the licensed PLS or PE who checked and approved the revision.

North Arrow Conventions and Meridian Types

Every survey drawing must display a prominent north arrow establishing directional orientation. By drafting convention, north points toward the top of the plan sheet whenever possible. If an alignment orientation requires rotating the sheet, north must point to the left or top-left, never downward.

Surveying recognizes three distinct north references:

True North (Geodetic North): The direction along a meridian toward the Earth's geographic North Pole (the rotational axis of the planet). It remains constant regardless of position or time.

Magnetic North: The direction indicated by a magnetic compass needle pointing toward the Earth's magnetic north pole. Magnetic north fluctuates continuously due to secular variation and local magnetic anomalies. The angular difference between True North and Magnetic North is called magnetic declination .

Grid North: The direction parallel to the central meridian of a plane coordinate grid system (such as the State Plane Coordinate System SPCS or Universal Transverse Mercator UTM). The angular difference between True North and Grid North at any given location is known as the grid declination or mapping angle .