Study guide
10.3 On-Site Scoping Methodology, Itemized Estimating & Depreciation Calculation
New York Claims Adjuster Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: New York Adjuster Licensing & Regulatory Oversight
1.1 NY DFS Authority, Superintendent Powers & Independent Adjuster Licensing (§ 2108) 1.2 License Maintenance, the Bond & Certificate Exemptions, Grounds for Revocation (§ 2110) & Temporary Permits 1.3 Regulation 64 (11 NYCRR 216) Mandatory Timelines & Unfair Claims Settlement Practices 1.4 The New York Standard Fire Policy (§ 3404), Suit Against the Insurer, Cancellation & Nonrenewal, DFS Cybersecurity & TRIA
2 Chapter 2: New York Auto Insurance Laws & No-Fault (Article 51)
2.1 NY Mandatory Motor Vehicle Liability Limits (25/50/10) & Financial Security 2.2 Article 51 No-Fault PIP: $50,000 Basic Economic Loss & Serious Injury Threshold 2.3 SUM / UM / UIM Endorsements & Regulation 64 Physical Damage Settlement Rules 2.4 The Personal Auto Policy (PP 00 01): Parts A–F, Who Is an Insured & New York Endorsements 2.5 Vehicle Parts and Construction, Repair Terminology, Regulation 79 Inspections, Rideshare & Supplemental Spousal Liability
3 Chapter 3: General Insurance Principles & Contract Law
3.1 Legal Elements of Insurance Contracts, Adhesion & Principle of Indemnity 3.2 Standard Policy Structure (DICEED), Policy Conditions & Duties After Loss 3.3 Warranties vs. Representations, Concealment, Waiver & Estoppel in Claims 3.4 Third-Party Interests, Other Insurance & Limits of Liability, Blanket vs. Specific Insurance & Construction Classes
4 Chapter 4: Property Insurance Concepts, Valuation & Coinsurance
4.1 Pure vs. Speculative Risk, Hazards, Proximate Cause & Concurrent Causation 4.2 Property Valuation Methods: ACV, Replacement Cost, Functional RC & Agreed Value 4.3 Coinsurance Formula, Step-by-Step Penalty Calculations & Practical Examples
5 Chapter 5: Homeowners & Dwelling Property Policies
5.1 Homeowners Policy Forms (HO-2 through HO-8) & Section I Coverages A–D 5.2 Section I Covered Perils, Major Exclusions & 80% Replacement Cost Settlement 5.3 Dwelling Policy Program (DP-1, DP-2, DP-3), Other Structures & Fair Rental Value 5.4 National Flood Insurance Program (NFIP), WYO, 30-Day Rule & Specialty Floaters 5.5 New York Special Provisions & Selected Homeowners and Dwelling Endorsements
6 Chapter 6: Principles of Liability, Tort Law & Personal Liability
6.1 Law of Negligence, Elements of Tort & NY Pure Comparative Fault (CPLR 14-A) 6.2 Homeowners Section II: Coverage E Personal Liability & Coverage F Medical Payments 6.3 Personal Umbrella Policies, Underlying Limits & Self-Insured Retention (SIR)
7 Chapter 7: Commercial Property & Package Policies
7.1 Building and Personal Property Coverage Form (BPP): Covered Property & Extensions 7.2 Causes of Loss Forms (Basic, Broad, Special), Business Income & Extra Expense 7.3 Businessowners Policy (BOP) Eligibility, Packaged Coverages & Endorsements 7.4 Commercial Crime (2013): Burglary, Robbery and Theft Definitions, the Eight Insuring Agreements & Discovery vs. Loss Sustained 7.5 Farm Coverage: Property Coverages A–G, Farm Liability Coverages H–J, Mobile Agricultural Equipment & Livestock 7.6 Businessowners Liability Coverage Form, Common Policy Conditions & Selected BOP Endorsements
8 Chapter 8: Commercial General Liability (CGL) & Commercial Auto
8.1 CGL Form Structure: Occurrence vs. Claims-Made, Retroactive Dates & ERPs 8.2 CGL Coverage A, B, C, Premises/Operations vs. Products-Completed Operations & Exclusions 8.3 Business Auto Coverage Form (BACF), Symbols 1–9, Liability & Physical Damage 8.4 Garage/Auto Dealers, Truckers and Motor Carrier Forms, MCS-90 & New York Commercial Auto PIP Endorsements
9 Chapter 9: Marine Insurance, Bonds & Specialty Lines
9.1 Nationwide Marine Definition, Commercial Floaters & Equipment Breakdown 9.2 Ocean Marine: Hull, Cargo, Freight, Protection & Indemnity (P&I) & General Average 9.3 Surety Bonds vs. Insurance: Principal, Obligee, Surety, Fidelity vs. Surety 9.4 Fidelity Coverages: Bond Period and Discovery Period, Employee Dishonesty Forms, ERISA Bonds, Financial Institution Bonds & Public Employee Bonds 9.5 Aviation Hull Coverages & Aircraft Liability Coverages
10 Chapter 10: The Claims Process: Investigation, Scoping & Coverage Analysis
10.1 First Notice of Loss (FNOL), Initial Intake & Coverage Verification Checklist 10.2 Reservation of Rights (ROR) Letters vs. Non-Waiver Agreements & Estoppel Prevention 10.3 On-Site Scoping Methodology, Itemized Estimating & Depreciation Calculation 10.4 Salvage Rights, Total Loss Determinations & Subrogation Recovery
11 Chapter 11: Claim Documentation, Dispute Resolution & Settlement
11.1 Physical Evidence, Chain of Custody, Recorded Statements, EUO & Sworn Proof of Loss 11.2 Policy Appraisal Clause, Umpire Selection, Binding Awards & Alternative Dispute Resolution 11.3 Claim Negotiation Principles, Release Forms, Lien Resolution & Closing Reports 11.4 Adjuster Report Writing, Claim File Documentation & the Declaratory Judgment Action
12 Chapter 12: Insurance Fraud Detection, SIU & Adjuster Ethics
12.1 Property, Casualty & Auto Fraud Red Flags, Arson Indicators & Staged Losses 12.2 Special Investigation Units (SIU), NY DFS Frauds Bureau & Penal Law § 176 12.3 Adjuster Code of Ethics, Fiduciary Duty, Regulation 169 Privacy & 18 U.S.C. §§ 1033/1034
13 Chapter 13: Accident & Health Insurance Basics
13.1 Accident & Health Claims: Accidental Injury vs. Sickness, Disability Income, Medical Expense & Long-Term Care 13.2 Classes of A&H Coverage, Limited Policies & Common Exclusions 13.3 A&H Claims Handling: Notice, Claim Forms, Proof of Loss, Physical Examination & New York Prompt Pay
14 Chapter 14: Understanding the Language of Medical Reports
14.1 Medical Terminology: Roots, Prefixes, Suffixes, Location and Movement Terms, Abbreviations & Specialties 14.2 Basic Human Anatomy, Common Injuries and Diseases & Diagnostic Tests
15 Chapter 15: Workers' Compensation Insurance
15.1 Workers' Compensation Law Types, New York Exclusive Remedy (WCL § 11), Covered Employment & Grave Injury 15.2 New York Benefits, Waiting Period, Notice and Filing Deadlines & Board Claims Reporting 15.3 The Workers' Compensation and Employers Liability Policy, Federal Acts & Other Sources of Coverage
16 Chapter 16: Specialty Liability, Excess Lines & Other Coverages
16.1 Specialty Liability: E&O, Professional, D&O, Fiduciary, Liquor/Dram Shop, EPLI, Environmental & Cyber 16.2 Excess Lines (Reg 41), Identity Theft, Watercraft, Recreational Vehicles & Difference in Conditions 16.3 Crop Insurance, Federal Multi-Peril Crop Insurance & the New York Multi-Peril Crop Adjuster License
10.3 On-Site Scoping Methodology, Itemized Estimating & Depreciation Calculation
Key Takeaways Explain This Topic AI
On-site scoping follows a disciplined exterior-to-interior, top-to-bottom, room-by-room methodology, prioritizing physical safety, accurate dimensional measurement, and progressive three-tier photography.
Itemized repair estimates utilize unit-cost pricing—separating labor, materials, equipment, and debris removal—to provide transparent, verifiable line-item documentation.
Contractor Overhead and Profit (O&P), conventionally calculated as 10% overhead and 10% profit ('10 and 10'), is applicable when a project is complex enough to require the coordination and supervision of multiple distinct construction trades.
Actual Cash Value (ACV) equals Replacement Cost Value (RCV) minus physical depreciation; under replacement cost policies, recoverable depreciation is held back until repairs are completed.
The age-life depreciation formula computes the depreciation percentage by dividing an item's effective age by its total expected useful life.
Last updated: September 2026
On-Site Scoping Methodology, Itemized Estimating & Depreciation Calculation
Exam Focus: The Series 17-70 examination tests candidates on the sequence of physical damage inspections, structural scoping checklists, itemized unit-cost estimating principles, the rules governing Contractor Overhead and Profit (O&P), and mathematical calculations of age-life depreciation and Actual Cash Value (ACV).
On-Site Inspection Protocols & Perimeter Establishment
The on-site inspection is the physical core of property loss adjusting. The adjuster must balance thorough scientific evidence gathering with professional customer communication. Every field inspection follows a structured protocol:
1. Site Safety and Hazard Recognition
Before entering any damaged structure, the adjuster must assess life safety hazards:
Structural Stability: Compromised load-bearing framing, sagging roofs, collapsed foundation walls, or unsupported masonry chimneys.
Utilities: Active high-voltage electrical wires, energized standing water, fractured natural gas or propane supply lines, and compromised fuel oil tanks.
Environmental and Biohazards: Friable asbestos insulation, airborne mold spores, Category 3 "black water" sewage backup, or toxic soot residues.
Personal Protective Equipment (PPE): Hard hat, steel-toed boots, eye protection, heavy work gloves, and appropriate respiratory protection (N95 or half-face P100 respirator).
2. Meeting Policyholders and Representatives
The adjuster meets the insured, public adjuster, or contractor on-site to conduct an opening conference. The adjuster explains the inspection process, confirms the reported cause of loss, listens to the policyholder's narrative, and clarifies that the field inspection is an information-gathering exercise subject to final coverage determination.
3. Establishing the Damage Perimeter
The adjuster walks the full premises to establish clear boundaries:
The Origin Zone: The specific room or structural point where the peril originated (e.g., failed dishwasher supply line or furnace burner failure).
Primary Damage Zone: Areas sustaining direct, severe physical destruction.
Secondary / Transition Zone: Contiguous areas affected by smoke, water migration, moisture humidity, or foot traffic.
Unaffected Baseline: Undamaged rooms that serve as a comparative standard for pre-loss architectural finish, grade, and maintenance condition.
Systematic Scoping Methodology & Physical Measurement
Scoping is the systematic, room-by-room process of taking physical measurements, recording detailed item-by-item structural damage, and creating an exhaustive inventory of repairs required to restore the property to its pre-loss condition.
The Systematic Geometric Sweep
Adjusters must never wander haphazardly through a property. Scoping follows a strict geometric sequence:
Exterior Elevations: Front (South), Right (East), Rear (North), Left (West) elevations.
Roof & Attic: Roof covering, flashing, gutters, chimneys, attic framing, and insulation.
Interior - Top to Bottom: Highest finished level down through living areas to basement or crawlspace.
Room Inspection - Clockwise Pattern: Inside each room, the adjuster begins at the entry door, documents room dimensions, and progresses clockwise around the four walls, ceiling, and floor.
Dimensional Accuracy and Formulas
Accurate estimating requires precise measurements:
Perimeter: 2 × ( Length + Width ) 2 \times (\text{Length} + \text{Width}) 2 × ( Length + Width ) . Essential for baseboards, crown molding, and sill plates.
Wall Surface Area: ( Perimeter × Ceiling Height ) − Openings (doors/windows) (\text{Perimeter} \times \text{Ceiling Height}) - \text{Openings (doors/windows)} ( Perimeter × Ceiling Height ) − Openings (doors/windows) .
Ceiling and Floor Area: Length × Width \text{Length} \times \text{Width} Length × Width .
Roof Pitch and Waste: Pitch represents vertical rise per 12 inches of horizontal run (e.g., 6/12 pitch). Roof area must incorporate pitch multiplication factors and standard shingle waste allowances (typically 10% on simple gable roofs; 15% on complex hip roofs with valleys).
The Three-Tier Photographic Protocol
Photographs provide the evidentiary foundation for the estimate. Every damaged component requires three sequential photographs:
Wide-Angle / Overview: Captures the full room or elevation, including street address placards, establishing macro context and overall spatial relationships.
Medium-Distance / Orientation: Illustrates the specific damaged building element in relationship to surrounding framing or unaffected finishes.
Close-Up / Macro: Documents minute physical failure details, impact punctures, burn patterns, water lines, serial number placards, and manufacturer labels, ideally with a measuring tape or scale marker in the frame.
Scoping Zone Specific Building Components Checked Measurement Unit
Roofing Decking, underlayment, shingles, drip edge, ridge cap, flashing, vents Squares (100 sq ft) / Linear Feet
- Ceilings Drywall (1/2" vs 5/8"), texture, framing joists, blown/batt insulation Square Feet
- Walls Studs, insulation, drywall, primer, paint coats, wallpaper Square Feet
- Flooring Subfloor (plywood/OSB), underlayment, hardwood, tile, pad, carpet Square Feet / Square Yards
- Millwork Baseboard, shoe mold, door casing, crown molding, window sills Linear Feet
- MEP Systems Wiring runs, outlets, HVAC ductwork, copper/PEX pipe, plumbing fixtures Each / Linear Feet
- Itemized Repair Estimating & Unit-Cost Pricing
Under New York Regulation 64 (11 NYCRR 216.6), insurance estimates must be sufficiently detailed so the claimant can verify the scope and cost of repairs. Adjusters utilize computer-assisted estimating databases (such as Xactimate or Symbility) based on unit-cost pricing rather than vague lump-sum allowances.
The Four Core Cost Components
Every line-item in a unit-cost estimate breaks down into:
Labor: Hourly wage rates based on regional prevailing wages, including payroll taxes, workers' compensation insurance, and employer contributions.
Materials: The physical cost of purchasing raw materials, lumber, drywall, roofing, or paint from local wholesale distributors.
Equipment Rental: The cost of specialized apparatus required to perform the task (e.g., commercial dehumidifiers, negative air scrubbers, boom lifts, dumpsters).
Debris Removal & Disposal: The labor and municipal landfill disposal fees required to tear out, load, haul away, and dispose of damaged components.
Contractor Overhead and Profit (O&P): The "10 and 10" Rule
In construction contracting, Overhead represents indirect operational expenses necessary to run a business (office lease, licensing, staff salaries, liability insurance, advertising), while Profit is the net return earned by the general contractor.
The "10 and 10" Standard: Contractor O&P is conventionally calculated as 10% for overhead and 10% for profit added to the subtotal of direct repair costs.
The Multi-Trade Coordination Rule: O&P is appropriate whenever a repair project is sufficiently complex to require the coordination, scheduling, and oversight of multiple distinct construction trades (typically three or more, such as framing, plumbing, electrical, and roofing). If an insured hires a general contractor to coordinate diverse subcontractors, O&P is a recognized, payable cost of repair. Adjusters cannot arbitrarily exclude O&P when general contractor supervision is reasonably necessary to complete the restoration.
Depreciation Methodologies & Settlement Mechanics
Depreciation is the deduction from replacement cost reflecting the loss in value of property resulting from physical deterioration, age, wear and tear, and obsolescence.
The Three Types of Depreciation
Physical Deterioration: Tangible wear, tear, corrosion, decay, and environmental exposure.
Functional Obsolescence: Loss of usefulness due to outdated design, inadequate capacity, or super-adequacy (e.g., an antiquated electrical fuse box or outdated floor plan).
Economic / External Obsolescence: Loss in value caused by factors external to the property (e.g., changes in zoning or proximity to industrial pollution).
Straight Age-Life Depreciation Formula
The standard actuarial method for calculating physical depreciation in property adjusting is the straight age-life method : Depreciation Percentage = Effective Age Normal Useful Life Expectancy \text{Depreciation Percentage} = \frac{\text{Effective Age}}{\text{Normal Useful Life Expectancy}} Depreciation Percentage = Normal Useful Life Expectancy Effective Age Total Depreciation Amount = Replacement Cost Value (RCV) × Depreciation Percentage \text{Total Depreciation Amount} = \text{Replacement Cost Value (RCV)} \times \text{Depreciation Percentage} Total Depreciation Amount = Replacement Cost Value (RCV) × Depreciation Percentage Actual Cash Value (ACV) = Replacement Cost Value (RCV) − Total Depreciation Amount \text{Actual Cash Value (ACV)} = \text{Replacement Cost Value (RCV)} - \text{Total Depreciation Amount} Actual Cash Value (ACV) = Replacement Cost Value (RCV) − Total Depreciation Amount
Note on Effective Age: Effective age is determined by the adjuster's assessment of maintenance and condition, which may be greater or less than chronological age. A 10-year-old roof maintained in pristine condition may have an effective age of only 5 years.
Recoverable vs. Non-Recoverable Depreciation
Under a standard Replacement Cost (RCV) policy, property claims are settled through a two-stage payment mechanism:
Initial ACV Payment: The insurer calculates total RCV, subtracts total depreciation, and deducts the policy deductible, issuing an initial payment for the net ACV.
Recoverable Depreciation Holdback: The withheld depreciation amount is designated as recoverable depreciation . Once the insured completes the physical repair or replacement of the damaged property and submits verified contractor invoices within the policy time limit (typically 180 days to 1 year under standard ISO forms), the insurer issues a second check for the withheld depreciation, up to the amount actually spent.
Non-Recoverable Depreciation: If a policy is written strictly on an Actual Cash Value (ACV) basis, or if a specific component endorsement applies (such as a cosmetic roof surfacing schedule), the depreciation is permanent and non-recoverable.
Practical Mathematical Scenario: Structural Fire Loss
A residential dwelling sustains kitchen fire and smoke damage. The adjuster completes an itemized unit-cost estimate:
Drywall, Framing, Paint, Flooring RCV Subtotal: $40,000
Project requires 4 distinct trades: General Contractor O&P (10% overhead = $4,000; 10% profit on subtotal + overhead [$44,000 × \times × 10%] = $4,400): $8,400
Total Replacement Cost Value (RCV): $48,400
Age-Life Depreciation: Average useful life of finishes is 20 years; effective age is 5 years ( 5 / 20 = 25 % 5 / 20 = 25\% 5/20 = 25% depreciation). Total depreciation is 48 , 400 × 25 % = $ 12 , 100 48,400 \times 25\% = \text{\textdollar}12,100 48 , 400 × 25% = $ 12 , 100 .
Actual Cash Value (ACV): 48 , 400 − $ 12 , 100 = $ 36 , 300 48,400 - \text{\textdollar}12,100 = \text{\textdollar}36,300 48 , 400 − $ 12 , 100 = $ 36 , 300 .
Policy Deductible: $1,500.
Initial Payment (Net ACV): 36 , 300 − $ 1 , 500 = $ 34 , 800 36,300 - \text{\textdollar}1,500 = \text{\textdollar}34,800 36 , 300 − $ 1 , 500 = $ 34 , 800 .
Subsequent Payment upon Complete Repair: Once the insured presents paid invoices verifying completion of all repairs totaling $48,400, the insurer issues a supplemental check for the full $12,100 recoverable depreciation.