Study guide

12.2 CCTV / Video Surveillance and Specialty Systems

New York Security or Fire Alarm Installer License Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 81-Hour Qualifying Education 1.3 Application, Fees, and Fingerprints

2 Who Must Be Licensed

2.1 License Required and Exemptions 2.2 Install, Service, Maintain, Assist, and Network 2.3 Master Electrician Waiver 2.4 NYS DOS License versus NYC FDNY and Local Inspection

3 Business Practice, Employees, and Discipline

3.1 Employees, ID Cards, and Fingerprints 3.2 Qualifying Officers, Display, Records, and Advertising 3.3 Discipline, Criminal Bars, and Penalties

4 Standards and Codes

4.1 Standards Organizations 4.2 New York Uniform Fire Prevention and Building Code and the AHJ 4.3 Listed Equipment, Compatibility, and AHJ Approval

5 NEC and Article 760

5.1 NEC Overview for Alarm Work 5.2 Power-Limited versus Non-Power-Limited Fire Alarm Circuits 5.3 Fire Alarm Cable Types, Plenums, Risers, and Abandoned Cable

6 Basic Electricity I

6.1 Voltage, Current, Resistance, and Ohm’s Law 6.2 Series and Parallel Circuits 6.3 Power, Energy, and Watt’s Law

7 Basic Electricity II

7.1 AC, DC, Transformers, and Low-Voltage Power Supplies 7.2 Batteries for Alarm Systems 7.3 Meters, Opens, Shorts, and Ground Faults

8 Control Devices

8.1 Control Panel Functions and Architecture 8.2 Conventional Zones and IDCs 8.3 Addressable Systems and Signaling Line Circuits

9 Circuits, Battery Calculations, and Job Planning

9.1 Notification Appliance Circuits and Circuit Classes 9.2 Secondary Power and Battery Calculations 9.3 Job Planning and Record Keeping

10 Alarm Transmission

10.1 Digital Alarm Communicators and Legacy Phone Paths 10.2 IP, Cellular, and Dual-Path Communications 10.3 Central Stations, Signal Types, and Path Supervision

11 Motion Detection

11.1 Passive Infrared Motion Detection 11.2 Microwave, Ultrasonic, and Dual-Technology Sensors 11.3 Placement, Pet Immunity, Masking, and Walk-Test

12 Perimeter, Video, Access Control, and False Alarms

12.1 Perimeter Systems 12.2 CCTV / Video Surveillance and Specialty Systems 12.3 Access Control 12.4 False Alarm Prevention

13 Fire Detection Devices

13.1 Fire Behavior and Detector Application 13.2 Smoke Detection 13.3 Heat Detection

14 Other Initiating Devices and Notification

14.1 Manual Stations, Waterflow, Supervisory, Duct, and CO 14.2 Horns, Strobes, Speakers, and Candela 14.3 Notification Placement, Public Mode, and Accessibility

15 Fire Alarm Systems

15.1 System Types and Occupancy Context 15.2 Pathways, Classes, and Survivability 15.3 Elevator Recall, HVAC Shutdown, Door Release, and Suppression Release

16 Job Safety and Professional Conduct

16.1 Job Safety 16.2 Overview and Professional Conduct 16.3 Service Role versus Installation Role

17 Testing and Inspection

17.1 Acceptance Testing and Commissioning 17.2 Periodic Inspection, Testing, and Maintenance Frequencies 17.3 ITM Documentation and Records

18 Troubleshooting and Device Service

18.1 Testing and Troubleshooting Methods 18.2 Panels, Alarm Devices, and Communications Service 18.3 Specialty Service Items

19 Maintenance, Programming, and False-Alarm Reporting

19.1 Maintenance Programs and Contracts 19.2 Maintenance, Inspection, and False Alarm Reporting 19.3 Programming, Access Codes, Bypass, and Hours of Operation

12.2 CCTV / Video Surveillance and Specialty Systems

Key Takeaways Explain This Topic AI

19 NYCRR 195.2(b)(1) requires the security or fire alarm installer license for CCTV or video surveillance used full-time or part-time for detection or monitoring of intrusion, break-in, theft, movement, sound, or fire.

19 NYCRR 195.1(g) defines a network as two or more alarm devices linked so they can exchange commands and share data for security, video, access, and alarm detection or notification.

Analog cameras typically ride coaxial cable to a digital video recorder; IP cameras typically ride Ethernet, often with Power over Ethernet, to a network video recorder.

19 NYCRR 196.8 clusters 0.5 hour of specialty systems with 1 hour of CCTV inside Module 3; specialty initiating includes holdup/panic, safe/vault contacts, temperature, and water sensors.

A camera job used to watch for break-in is licensed installer work even if someone markets it as 'just CCTV' and even if it runs only part of the day.

Last updated: September 2026

Module 3 of the New York qualifying course is not motion-and-contacts only. 19 NYCRR 196.8 also assigns 1 hour to CCTV systems and 0.5 hour to specialty systems . This Independent ExamFinch section clusters those hours, because the exam will mix them: a camera used to watch a door is a license question, and a holdup button next to the cash drawer is still an initiating device.

19 NYCRR 195.2(b)(1): when video requires the installer license

19 NYCRR 195.2(b)(1) is the sentence to memorize. A security and fire alarm installers license is required for the installation, maintenance, or servicing of a closed circuit television system (CCTV), or video surveillance system, if such system is used, either full-time or part-time, for the detection or monitoring of intrusion, break-in, theft, movement, sound or fire .

Read the triggers, not the marketing. The regulation does not say “only analog,” “only more than sixteen cameras,” or “only if it is connected to a burglar alarm panel.” It says CCTV or video surveillance . It says full-time or part-time . It says detection or monitoring of a listed list: intrusion, break-in, theft, movement, sound, or fire. A store camera system that a manager watches for shoplifting is monitoring theft. A loading-dock camera that trips a video-analytics rule after hours is detecting movement or intrusion. A camera aimed at a fire-alarm annunciator so a guard can see a trouble is monitoring fire. Part-time use still counts. Nights-and-weekends recording still counts.

19 NYCRR 195.1(a) already defines an alarm system as devices designed to signal intrusion, break-in, theft, movement, sound, fire, and similar conditions. 195.1(g) then defines a network as two or more alarm devices or equipment linked through any means, including ethernet, wifi, or serial bus, so they can communicate, exchange commands, and share data that may operate hardware for security, video, access, and alarm detection and/or notification . Video is inside the licensing vocabulary, not a side hobby.

What is not a 195.2(b)(1) trigger is a camera that is not used for those detection or monitoring purposes — for example a purely process camera on a production line with no security or fire use. Do not invent a bright-line “under four cameras” exemption; 195.2 does not write one. When the use is security or fire monitoring, the installer license is required. Selling the system to a consumer while subcontracting the install still requires the seller to be licensed under 195.2(a)(2) .

Analog versus IP cameras, PoE, and NVRs

Qualifying-course CCTV hours are conceptual, not a manufacturer certification. You still need the vocabulary the written exam can use.

Analog cameras typically send a composite video signal over coaxial cable (often RG-59 or RG-6, with power on a separate pair or a Siamese cable) to a digital video recorder (DVR) . The DVR digitizes, records, and may re-encode for remote viewing. Distance, connectors, and ground loops are analog-era field problems. IP cameras are network endpoints. They typically ride Ethernet to a network video recorder (NVR) or to server software. Each camera has an address on the network. Remote viewing, analytics, and shared storage live on that network.

Power over Ethernet (PoE) sends DC power and data on the same Ethernet cable from a PoE switch or injector. That is why a single run can land an IP camera without a local plug. PoE has listed power classes (commonly discussed as IEEE 802.3af/at and higher-power variants); the installer still sizes the switch budget, uses listed power-limited cable where required, and does not treat a camera cable as a substitute for a fire-alarm circuit. 195.2(c)(2) still keeps line-voltage connections to an outlet, junction box, or distribution panel in electrician territory. PoE is low-voltage network power, not a license exemption for the camera system as a whole.

An NVR records IP streams. A DVR records analog (or hybrid) inputs. Either box can sit in a locked room with a UPS. Neither box is a fire-alarm notification appliance. If the video system is used for detection or monitoring of the 195.2(b)(1) list, installing the cameras, the recorder, the PoE switch that is part of that system, and the programming that makes monitoring work is installer work under 195.1(c) and 195.1(g).

  • Topic Analog-centric IP-centric
  • Typical cable Coax (plus power pair) Ethernet
  • Typical recorder DVR NVR
  • Camera power Local plug or power supply Often PoE from a switch or injector
  • Addressing Channel on the DVR Network address / name
  • License trigger Use for detection or monitoring, not the cable type Same 195.2(b)(1) use test
  • In practice

A restaurant owner asks for “just four cameras” on the registers and the back door, viewed on a phone after hours, with motion pop-ups. That is part-time monitoring of theft and movement. 195.2(b)(1) requires the installer license. Calling the recorder an NVR instead of a DVR does not change the answer. Running the cameras on PoE does not change the answer. Subcontracting a “low-voltage helper” who is not an employee with a proper identification card does not change the answer.

Specialty systems (0.5 hour): initiating devices that are not doors or PIRs

The half-hour of specialty systems in 196.8 is short on purpose. Teach the devices as alarm initiating points , not as plumbing or HVAC side work.

Holdup and panic devices are manually actuated initiating devices. A holdup (often silent) is used in robberies so the teller or cashier can request help without an audible on the premises. A panic device may be audible, silent, or both, depending on how the panel and central station are programmed. Money clips, foot rails, and under-counter buttons are still initiating devices. They need listed mounting, a distinct zone or point type so the central station does not treat them as a burglary door, and a test method that does not dispatch police by accident. Duress codes at a keypad are programming, which 195.1(c) already calls installation.

Safe and vault contacts protect high-security containers. They may be high-security magnetic contacts, thermal sensors, or seismic sensors on a vault door or skin. They are perimeter-style initiating devices on a very valuable opening. Treat them as supervised alarm points with tamper, not as “the safe company will handle the switch.” If the point reports into the alarm system, hanging and programming it is alarm work.

Temperature sensors (high-temperature or freeze) and water sensors (spot leak / flood) are environmental initiating devices. A freeze sensor in a vacant building, a high-temp sensor in a server closet, or a water bug under an air handler still initiates an alarm or supervisory point on the control. They are in the specialty hour because they are not motion and not a door, but they are still detectors under 195.1. They are not a plumbing license substitute and they are not exempt as sprinklers under 195.2(c)(1). Sprinkler systems are exempt; a water bug that reports a flood to an alarm panel is not a sprinkler system.

Keep specialty brief and real: identify the condition, land it as a unique point, supervise the circuit or wireless transmitter, and tell the central station what the signal means. A holdup that reports as a generic burglary zone is a dispatch error waiting to happen. A water sensor on a 24-hour burglary loop will false-dispatch every time the mop bucket drips. Point type and programming are part of installing the specialty device.

Module 3 therefore spends 2.5 hours on perimeter , 0.5 on specialty , and 1 hour on CCTV before it reaches access control and false alarms. Video used for detection or monitoring is licensed. Specialty sensors that report intrusion, holdup, environmental damage, or fire-related conditions are licensed initiating devices. The exam will not give you a third category called “low-voltage extras.”

Module 3 hour weights from 19 NYCRR 196.8 (this chapter covers III–VII)