Study guide
16.3 Service Role versus Installation Role
New York Security or Fire Alarm Installer License Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 81-Hour Qualifying Education 1.3 Application, Fees, and Fingerprints
2 Who Must Be Licensed
2.1 License Required and Exemptions 2.2 Install, Service, Maintain, Assist, and Network 2.3 Master Electrician Waiver 2.4 NYS DOS License versus NYC FDNY and Local Inspection
3 Business Practice, Employees, and Discipline
3.1 Employees, ID Cards, and Fingerprints 3.2 Qualifying Officers, Display, Records, and Advertising 3.3 Discipline, Criminal Bars, and Penalties
4 Standards and Codes
4.1 Standards Organizations 4.2 New York Uniform Fire Prevention and Building Code and the AHJ 4.3 Listed Equipment, Compatibility, and AHJ Approval
5 NEC and Article 760
5.1 NEC Overview for Alarm Work 5.2 Power-Limited versus Non-Power-Limited Fire Alarm Circuits 5.3 Fire Alarm Cable Types, Plenums, Risers, and Abandoned Cable
6 Basic Electricity I
6.1 Voltage, Current, Resistance, and Ohm’s Law 6.2 Series and Parallel Circuits 6.3 Power, Energy, and Watt’s Law
7 Basic Electricity II
7.1 AC, DC, Transformers, and Low-Voltage Power Supplies 7.2 Batteries for Alarm Systems 7.3 Meters, Opens, Shorts, and Ground Faults
8 Control Devices
8.1 Control Panel Functions and Architecture 8.2 Conventional Zones and IDCs 8.3 Addressable Systems and Signaling Line Circuits
9 Circuits, Battery Calculations, and Job Planning
9.1 Notification Appliance Circuits and Circuit Classes 9.2 Secondary Power and Battery Calculations 9.3 Job Planning and Record Keeping
10 Alarm Transmission
10.1 Digital Alarm Communicators and Legacy Phone Paths 10.2 IP, Cellular, and Dual-Path Communications 10.3 Central Stations, Signal Types, and Path Supervision
11 Motion Detection
11.1 Passive Infrared Motion Detection 11.2 Microwave, Ultrasonic, and Dual-Technology Sensors 11.3 Placement, Pet Immunity, Masking, and Walk-Test
12 Perimeter, Video, Access Control, and False Alarms
12.1 Perimeter Systems 12.2 CCTV / Video Surveillance and Specialty Systems 12.3 Access Control 12.4 False Alarm Prevention
13 Fire Detection Devices
13.1 Fire Behavior and Detector Application 13.2 Smoke Detection 13.3 Heat Detection
14 Other Initiating Devices and Notification
14.1 Manual Stations, Waterflow, Supervisory, Duct, and CO 14.2 Horns, Strobes, Speakers, and Candela 14.3 Notification Placement, Public Mode, and Accessibility
15 Fire Alarm Systems
15.1 System Types and Occupancy Context 15.2 Pathways, Classes, and Survivability 15.3 Elevator Recall, HVAC Shutdown, Door Release, and Suppression Release
16 Job Safety and Professional Conduct
16.1 Job Safety 16.2 Overview and Professional Conduct 16.3 Service Role versus Installation Role
17 Testing and Inspection
17.1 Acceptance Testing and Commissioning 17.2 Periodic Inspection, Testing, and Maintenance Frequencies 17.3 ITM Documentation and Records
18 Troubleshooting and Device Service
18.1 Testing and Troubleshooting Methods 18.2 Panels, Alarm Devices, and Communications Service 18.3 Specialty Service Items
19 Maintenance, Programming, and False-Alarm Reporting
19.1 Maintenance Programs and Contracts 19.2 Maintenance, Inspection, and False Alarm Reporting 19.3 Programming, Access Codes, Bypass, and Hours of Operation
16.3 Service Role versus Installation Role
Key Takeaways Explain This Topic AI
19 NYCRR 195.1(c) installation is placing and connecting listed equipment, including programming access codes, system protocol, bypass features, and hours of operation.
19 NYCRR 195.1(d) maintaining is inspection and testing to detect and prevent problems and to establish proper operating conditions, including preventive programming of those same features.
19 NYCRR 195.1(e) servicing is repair, troubleshooting, or replacement of malfunctioning, failed, or damaged equipment, including associated programming.
Installing, maintaining, and servicing are all licensed activities under 19 NYCRR 195.2 and GBL Article 6-D; a service agreement does not create an unlicensed category.
19 NYCRR 195.1(f) assisting includes on-site and off-site participation and knowledge of on-line or off-line condition, access codes, protocols, bypass features, and hours of operation.
Last updated: September 2026
Module 5 is named Service and Maintenance , but the license is still for the business of installing, servicing, or maintaining security or fire alarm systems. Independent ExamFinch teaching for this section is 19 NYCRR 195.1(c), (d), and (e) applied to occupied buildings: when the truck roll is installation , when it is maintaining , and when it is servicing . All three are licensed activities. 195.1(f) assisting still includes remote knowledge of on-line or off-line status , access codes , protocols , bypass , and hours of operation .
Chapter 2 taught these definitions as scope vocabulary. This section is the Module 5 application: a service company that only helps with software is still in the licensed business, and a new device added during a service visit is still installation .
Installation: 195.1(c)
Installation includes, but is not limited to, the placing and connection of equipment and devices such as control panels, batteries, smoke or heat detectors ( excluding single-station battery-operated smoke alarms), motion detectors, switches, annunciators, sensors, sirens, horns, bells, networks, microprocessors (controls, logic keypads), other communication equipment, and similar devices.
Installation also includes programming the client's control panel, including programming or reprogramming for access codes , system protocol , bypass features , and hours of operation .
On a service truck, installation looks like:
- Adding a smoke detector to an existing signaling-line circuit
- Mounting a new communicator
- Placing a replacement FACU (the hardware placement is installation even if you arrived on a trouble call)
- Programming a new bypass schedule or hours of operation, even from a laptop off site
The last bullet is the Chapter 2 surprise item, restated for Module 5: software is not a loophole . Changing hours of operation is installation work under 195.1(c).
Maintaining: 195.1(d)
Maintaining includes, but is not limited to, inspection of a device, component, or system for the purpose of detecting and preventing problems with the same kinds of equipment listed above. Maintenance shall also include testing of alarm components, devices, or systems for the purpose of establishing proper operating conditions . Maintaining also includes inspection, testing, programming or reprogramming of the client's control panel, including testing, programming, or reprogramming for access codes, system protocol, bypass features, and hours of operation .
Maintaining is the preventive visit. The system has not necessarily failed. Annual inspection and testing, detector sensitivity checks, and programming that keeps trouble from developing are maintaining. Chapter 17 will cover inspection frequencies; this section only needs the 195.1 word.
If the exam stem says the technician is there to inspect, test, and program so problems are detected and prevented, the word is maintaining .
Servicing: 195.1(e)
Servicing includes, but is not limited to, the repair, troubleshooting, or replacement of malfunctioning, failed, or damaged equipment — batteries, smoke or heat detectors, motion devices, switches, annunciators, sensors, horns and bells, networks, microprocessors, communication equipment, and similar devices.
Servicing also includes testing, repair, troubleshooting, replacement, programming or reprogramming of the client's control panel, including those same actions for access codes, system protocol, bypass features, and hours of operation .
Servicing starts after something is wrong . A notification-appliance circuit that will not run, a detector in trouble that must be replaced, a communicator that will not transmit, a cracked battery — that is servicing. Programming done to restore failed equipment is servicing, not a free software gift.
Do not invent a fourth category called service call that avoids Article 6-D. If the work is repair, troubleshooting, or replacement of failed alarm equipment, it is servicing .
All three remain licensed
19 NYCRR 195.2(a) requires a license if a person or firm installs, maintains, or services alarm systems, or holds itself out as able to do so, including selling a system whose installation will be subcontracted. GBL §69-m is the statutory license requirement. A Module 5 maintenance agreement does not convert the firm into an unlicensed janitorial service.
195.1 term Field picture Programming?
(c) Installation Place or connect listed equipment, including new devices on an existing system Yes — codes, protocol, bypass, hours
(d) Maintaining Inspect and test to detect and prevent problems; confirm proper operation Yes — preventive programming
(e) Servicing Repair, troubleshoot, or replace malfunctioning, failed, or damaged equipment Yes — programming tied to the repair
(f) Assisting On-site or off-site participation, and knowledge of on-line/off-line status, codes, protocol, bypass, hours Knowledge alone can be assisting
195.2(c)(2) still leaves line-voltage connections to an outlet, junction box, or distribution panel outside the alarm license. That exception is not service work is unlicensed. It is the electrician landing.
Assisting includes remote knowledge: 195.1(f)
Assisting a licensed installer includes on-site and off-site participation in installation, maintenance, or servicing. Assisting also includes having access to or knowledge of the on-line or off-line condition of a system the licensed installer installed, serviced, or maintained. Assisting also includes having access to or knowledge of access codes, system protocols, bypass features, or hours of operation .
A dispatcher who never rolls a truck assists if they know whether the school panel is on line and what the bypass is. A remote technician who watches communicator status and holds the installer code is assisting. Employees who assist still need the 195.2(d) identification-card package from Chapter 3.
Chapter 19 will return to programming, access codes, bypass, and hours in more operational detail. Here the exam point is classification: remote knowledge is inside the licensed activity , not outside it.
Service role versus installation role on the same visit
Real jobs mix the words. Classify each task , then remember every task still needs the license.
Example 1. Annual test: walk devices, record results, adjust programming so a trouble does not develop. Maintaining.
Example 2. Same visit, a horn is found failed and is replaced, and the circuit is reprogrammed. The replacement is servicing . The scheduled test remains maintaining . Both are licensed.
Example 3. Same visit, the owner asks for two extra smokes in a new office. Placing and connecting those detectors is installation , even though the work order said service.
Example 4. After hours, a technician remotely changes hours of operation so the burglary partition arms at 6 p.m. Installation under 195.1(c) (programming hours). If a helper in the office knows those hours and the on-line status, that helper is assisting .
Example 5. A communicator failed. The technician troubleshoots, replaces the radio, and reloads the account. Servicing.
Exam traps
We only maintain does not drop the license.
We only service does not make adding a device something other than installation.
Programming hours or bypass is named in (c), (d), and (e); read the stem for new placement , prevention , or failed equipment .
Knowing on-line status remotely is assisting , not a hobby.
120-volt panelboard landings remain typically electrician work under 195.2(c)(2).
Single-station battery smoke alarms remain the narrow exclusion inside the installation list; a system detector is not that exclusion.