Study guide
6.4 Protective Devices, Discrimination & Coordination
NZ EWRB Electrician Registration Regulations
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Open-Reference Strategy & Permitted Materials 1.3 Electrician Registration Pathway & Limits of Work 1.4 Which Editions Apply: ESR Schedule 2 & the 13 November 2025 Update
2 Electricity Act & EWRB Framework
2.1 Electricity Act 1992 Framework 2.2 EWRB Role, Register & Registration Classes 2.3 Practising Licence & Electrician Limits of Work
3 Electricity (Safety) Regulations 2010
3.1 ESR 2010 Structure & Key Definitions 3.2 Electrically Safe & Electrically Unsafe 3.3 Duties of Electrical Workers & Competence 3.4 Certification Timeframes & Notification Duties under ESR
4 Prescribed Electrical Work
4.1 What Is Prescribed Electrical Work 4.2 PEW Risk Categories: Low, General, High 4.3 Who May Carry Out and Supervise PEW 4.4 High-Risk Work & Electrical Inspector Requirements
5 Certification Documents (CoC, ESC, RoI)
5.1 Certificate of Compliance (Regulation 65) 5.2 Electrical Safety Certificate (Safe to Connect / Use) 5.3 Record of Inspection (Regulation 72) 5.4 Record-Keeping, Retention & the Certification Chain 5.5 Record-Keeping Duties & the Statutory Clocks (regs 72A, 74E–74H)
6 AS/NZS 3000 Fundamentals
6.1 Structure of AS/NZS 3000 & Open-Book Navigation 6.2 Multiple Earthed Neutral (MEN) System 6.3 Basic Protection vs Fault Protection 6.4 Protective Devices, Discrimination & Coordination
7 RCDs, Shock Protection & Disconnection Times
7.1 RCD Shock-Protection Requirements 7.2 RCD Types, Classification & Installation Contexts 7.3 Disconnection Times (0.4 s / 5 s) & Earth Fault Path 7.4 Damp Situations & Additional Protection
8 Circuits, Maximum Demand & Voltage Drop
8.1 Division of Circuits & Final Subcircuits 8.2 Maximum Demand Principles 8.3 Voltage Drop Requirements & Worked Examples
9 Testing & Verification Core
9.1 Visual Inspection Before Testing 9.2 Continuity of Earthing & Protective Bonding 9.3 Insulation Resistance Testing (500 V DC, 1 MΩ) 9.4 Polarity & Correct Circuit Connections
10 EFLI, RCD Tests & Verification Sequence
10.1 Earth Fault Loop Impedance 10.2 RCD Operation Tests & Prospective Fault Current 10.3 Mandatory Test Sequence & Documentation
11 Safe Isolation & Personal Safety
11.1 Physiological Effects of Current & Shock Factors 11.2 Prove–Test–Prove Safe Isolation 11.3 Lock-Out/Tag-Out & Safety Tag System 11.4 Live-Work Controls, Fault Finding & Unsafe Installations
12 Electrical Codes of Practice & Schedule 2
12.1 NZECP 34 Electrical Safe Distances 12.2 NZECP 50 Repair of Domestic Electrical Equipment 12.3 NZECP 51 Electrical Wiring Work in Domestic Premises 12.4 NZECP 54 Recessed Luminaires & Auxiliary Equipment 12.5 ESR Schedule 2 & Companion Standards Overview
13 Installation Requirements
13.1 Consumer Mains, Point of Supply & Switchboards 13.2 Conductor Identification, Isolation, Labelling & IP Ratings 13.3 Cable Selection (AS/NZS 3008.1.2 NZ Conditions) 13.4 Construction Sites, Appliance Testing & Special Installations 13.5 Periodic Assessment, Warrants of Electrical Fitness & AS/NZS 3019
14 Exam Strategy & Key Numbers
14.1 Must-Know Numbers, Times & Thresholds 14.2 Exam Tactics & Common Traps
6.4 Protective Devices, Discrimination & Coordination
Key Takeaways Explain This Topic AI
Overcurrent protection uses MCBs, HRC fuses, and related devices selected for load, cable CCC, fault level, and utilisation category
Breaking capacity must equal or exceed prospective short-circuit current at the point of installation
Discrimination (selectivity) aims for the downstream device to clear a fault so upstream supply to healthy circuits remains
Backup protection and coordination ensure devices and cables survive and clear faults without cascading failure
Protective devices must coordinate with cable current-carrying capacity and earth-fault loop impedance so disconnection times for ADS are achieved
Last updated: August 2026
Why Coordination Is an Exam Domain, Not Just a Design Office Topic
AS/NZS 3000 requires electrical installations to be protected against overcurrent (overload and short-circuit) and to achieve automatic disconnection under earth-fault conditions. That forces protective devices to be selected and coordinated , not merely “fitted something that fits in the DIN rail.”
On the regulations exam, expect qualitative and scenario stems about:
- device types and roles,
- breaking capacity vs prospective short-circuit current (PSCC / PFC) ,
- discrimination / selectivity ,
- backup protection ,
coordination with cable current-carrying capacity (CCC) and fault loop / disconnection times .
You are not expected to design a full industrial board from first principles under exam time, but you are expected to recognise compliant reasoning and reject dangerous combinations.
- Overcurrent Devices: MCBs, HRC Fuses, Categories
- MCBs (miniature circuit-breakers)
MCBs are the common final-subcircuit and small distribution protective devices. Key selection ideas:
Rated current (In) — matched to load and not exceeding cable CCC (with diversity/grouping rules as applicable).
Trip curve / type (e.g. B, C, D families in common product lines) — affects instantaneous magnetic trip sensitivity to inrush vs fault current. Wrong curve can nuisance-trip motors or fail to trip promptly on modest faults.
Breaking capacity (Icn / Icu as marked) — maximum fault current the device can interrupt safely.
HRC fuses
High rupturing capacity (HRC) fuses remain common on mains, submains, and some equipment circuits. They offer high breaking capacity and distinctive time–current behaviour used in discrimination studies. Utilisation categories (product-standard markings) indicate suitability for cable protection, motor circuits, etc.—exam stems may ask whether a fuse type is appropriate for the duty, not just whether “a fuse is present.”
Utilisation categories and duty
“Utilisation category” language (from product standards referenced in installation practice) signals what kind of load and fault duty the device is intended for. Mixing a device intended only for limited duty into a high-fault industrial board is a coordination failure even if the ampere rating “matches the cable on a spreadsheet.”
Selection factor Question it answers
Rated current Will overload protection match load and cable?
Curve / time–current Will it ride through inrush yet clear faults?
Breaking capacity Can it interrupt the prospective fault current?
Utilisation / application Is the device right for the circuit duty?
Poles / switched neutral rules Does isolation and RCD coordination remain correct?
Prospective Short-Circuit Current and Breaking Capacity
At any point in an installation, a bolted short circuit can produce a prospective short-circuit current determined by supply capacity, transformer impedance, and conductor impedance up to that point.
Rule candidates must internalise:
The protective device’s rated breaking capacity at the point of installation must be ≥ prospective short-circuit current at that point (unless a validated backup arrangement is used).
If PSCC exceeds device breaking capacity, the device may fail violently under fault—arc, case rupture, fire. Exam stems that give a high fault level at a main switchboard and a low-kA MCB without backup are testing this inequality.
Practical cues
Closer to the supply transformer / service mains → higher prospective fault current.
Long cable runs downstream → fault level falls; device ratings can sometimes step down if calculated , not assumed.
Replacing a main fuse with a high-capacity supply upgrade without checking downstream device kA ratings is a classic real-world and exam hazard pattern.
Discrimination / Selectivity
Discrimination (selectivity) means that for a fault on a downstream circuit, the downstream device operates and the upstream device remains closed , so only the faulty circuit is lost.
Why it matters
Maintains supply to healthy circuits (safety systems, other tenants, critical loads).
Reduces operational disruption and diagnostic confusion.
Is a design goal for main → submain → final device chains.
How it is achieved (conceptually)
Time–current curve separation (upstream slower or higher threshold for the same fault current).
Fuse–fuse or fuse–breaker combinations published by manufacturers.
Adequate rating ratios between upstream and downstream devices (rule-of-thumb ratios appear in manufacturer data—do not invent numbers not in your references).
Total discrimination over the full fault-current range is not always achievable; partial discrimination may be accepted for some designs. Exam answers should prefer “downstream clears first where practicable” over “any device can trip, order does not matter.”
- Fault location Desired operation
- Final subcircuit fault Final MCB/fuse opens; submain and main stay in
- Submain fault Submain device opens; main stays in if possible
- Main board bus fault Main device operates; energy limited as designed
- Backup Protection
Backup protection (cascading) is a coordinated arrangement where an upstream device with adequate breaking capacity helps a downstream device that alone might not be rated for the full prospective fault current. It is a designed pairing—not wishful thinking that “something upstream will save it.”
Exam caution:
Backup does not excuse random undersized breakers without manufacturer-validated combinations.
Backup arrangements must still leave the installation safe and compliant with AS/NZS 3000 selection rules.
If a stem offers “any upstream fuse automatically backups any MCB,” treat that as false without a proper coordination basis.
Coordination with Cable CCC and Fault Loop (ADS)
Protective devices do two related jobs that exam stems mix:
1) Overload / short-circuit protection of conductors
Device ratings and settings must protect conductors so that overload and short-circuit energy do not damage insulation. Cable current-carrying capacity (often from AS/NZS 3008.1.2 in NZ conditions for detailed selection—B-level companion knowledge) must not be treated as optional. A 32 A breaker on a cable that can only carry far less under its installation method is a coordination failure.
2) Earth-fault disconnection times
For fault protection via ADS, the device must operate within required disconnection times (commonly examined 0.4 s and 5 s contexts depending on circuit type—detail in the RCD/disconnection chapter). That couples device trip curves to earth-fault loop impedance (Zs / EFLI) limits. A breaker that never sees enough fault current because Zs is too high will not achieve ADS—even if its ampere rating “matches the load.”
- Coordination question Pass condition (concept)
- Overload In and installation method protect cable CCC
- Short-circuit energy Device clears before cable damage
- Breaking capacity ≥ PSCC (or validated backup)
- Discrimination Downstream preferred for downstream faults
- ADS Fault current and device curve meet disconnection time
- Practical Switchboard Scenarios for the Exam
Practise reasoning aloud on patterns like these:
Main HRC fuse → submain MCB → final MCBs — fault on final circuit should clear final MCB; if main fuse always opens first, discrimination has failed.
High PSCC at main board, low-kA final MCBs — check breaking capacity or backup; “it’s only a lighting circuit” does not reduce bolted-fault energy if the board is close to a stiff supply.
Cable upgrade without device review — larger cable may raise prospective fault current at a point of installation or change loop impedance; reassess devices.
RCD + MCB (RCBO) chains — residual-current function does not remove the need for overcurrent rating, CCC match, and fault-level adequacy.
Earth fault with high Zs — overcurrent device may not trip in time; design may require reduced Zs, different device characteristics, or residual-current protection as required by the Rules—not ignoring the loop.
Open-book tip
Flag AS/NZS 3000 regions on protection against overcurrent , device selection , and cross-references to verification of fault loop. Use manufacturer curves only if your permitted materials include them; otherwise stick to principles: downstream first, kA ≥ PSCC, In vs CCC, ADS times vs Zs .
Closing synthesis for Chapter 6
You now have the AS/NZS 3000 foundation: how to navigate the book , how MEN earthing makes fault paths work , how basic and fault protection layers fit , and how protective devices must coordinate . Later chapters specialise into RCDs, disconnection numbers, circuit division, demand, voltage drop, and Section 8 testing—the verification half of the same safety system.