Study guide
11.2 Prove–Test–Prove Safe Isolation
NZ EWRB Electrician Registration Regulations
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Open-Reference Strategy & Permitted Materials 1.3 Electrician Registration Pathway & Limits of Work 1.4 Which Editions Apply: ESR Schedule 2 & the 13 November 2025 Update
2 Electricity Act & EWRB Framework
2.1 Electricity Act 1992 Framework 2.2 EWRB Role, Register & Registration Classes 2.3 Practising Licence & Electrician Limits of Work
3 Electricity (Safety) Regulations 2010
3.1 ESR 2010 Structure & Key Definitions 3.2 Electrically Safe & Electrically Unsafe 3.3 Duties of Electrical Workers & Competence 3.4 Certification Timeframes & Notification Duties under ESR
4 Prescribed Electrical Work
4.1 What Is Prescribed Electrical Work 4.2 PEW Risk Categories: Low, General, High 4.3 Who May Carry Out and Supervise PEW 4.4 High-Risk Work & Electrical Inspector Requirements
5 Certification Documents (CoC, ESC, RoI)
5.1 Certificate of Compliance (Regulation 65) 5.2 Electrical Safety Certificate (Safe to Connect / Use) 5.3 Record of Inspection (Regulation 72) 5.4 Record-Keeping, Retention & the Certification Chain 5.5 Record-Keeping Duties & the Statutory Clocks (regs 72A, 74E–74H)
6 AS/NZS 3000 Fundamentals
6.1 Structure of AS/NZS 3000 & Open-Book Navigation 6.2 Multiple Earthed Neutral (MEN) System 6.3 Basic Protection vs Fault Protection 6.4 Protective Devices, Discrimination & Coordination
7 RCDs, Shock Protection & Disconnection Times
7.1 RCD Shock-Protection Requirements 7.2 RCD Types, Classification & Installation Contexts 7.3 Disconnection Times (0.4 s / 5 s) & Earth Fault Path 7.4 Damp Situations & Additional Protection
8 Circuits, Maximum Demand & Voltage Drop
8.1 Division of Circuits & Final Subcircuits 8.2 Maximum Demand Principles 8.3 Voltage Drop Requirements & Worked Examples
9 Testing & Verification Core
9.1 Visual Inspection Before Testing 9.2 Continuity of Earthing & Protective Bonding 9.3 Insulation Resistance Testing (500 V DC, 1 MΩ) 9.4 Polarity & Correct Circuit Connections
10 EFLI, RCD Tests & Verification Sequence
10.1 Earth Fault Loop Impedance 10.2 RCD Operation Tests & Prospective Fault Current 10.3 Mandatory Test Sequence & Documentation
11 Safe Isolation & Personal Safety
11.1 Physiological Effects of Current & Shock Factors 11.2 Prove–Test–Prove Safe Isolation 11.3 Lock-Out/Tag-Out & Safety Tag System 11.4 Live-Work Controls, Fault Finding & Unsafe Installations
12 Electrical Codes of Practice & Schedule 2
12.1 NZECP 34 Electrical Safe Distances 12.2 NZECP 50 Repair of Domestic Electrical Equipment 12.3 NZECP 51 Electrical Wiring Work in Domestic Premises 12.4 NZECP 54 Recessed Luminaires & Auxiliary Equipment 12.5 ESR Schedule 2 & Companion Standards Overview
13 Installation Requirements
13.1 Consumer Mains, Point of Supply & Switchboards 13.2 Conductor Identification, Isolation, Labelling & IP Ratings 13.3 Cable Selection (AS/NZS 3008.1.2 NZ Conditions) 13.4 Construction Sites, Appliance Testing & Special Installations 13.5 Periodic Assessment, Warrants of Electrical Fitness & AS/NZS 3019
14 Exam Strategy & Key Numbers
14.1 Must-Know Numbers, Times & Thresholds 14.2 Exam Tactics & Common Traps
11.2 Prove–Test–Prove Safe Isolation
Key Takeaways Explain This Topic AI
Prefer work on isolated equipment: dead working removes supply energy as the primary hazard control
PROVE–TEST–PROVE: prove the tester on a known live source, test the circuit is de-energised, prove the tester still works
Test before touch—never assume a switch position, label, or verbal assurance equals isolation
Identify all sources of supply, including alternative supplies, UPS, generators, and PV/backfeed paths
- Complex sites need written isolation procedures so every source, lock, and test point is controlled
- Last updated: August 2026
Benefits of Working on Isolated Equipment
Dead working —performing PEW on equipment that has been safely isolated—is the default preference for good reason:
Removes electrical energy as the primary shock and arc source at the work point
Allows continuity, insulation, and construction work without relying solely on PPE and insulated tools to manage live risk
Supports clear LOTO and tagging so others do not re-energise the circuit under you
Aligns with the hierarchy of controls: eliminate the hazard where practicable before relying on administrative or PPE controls
Isolation is not “flipping a switch and hoping.” Competent isolation is a process : identify sources, isolate, secure against re-energisation, prove dead , then work—and restore only under a controlled return-to-service sequence.
The PROVE–TEST–PROVE Rule
Voltage indicators and multimeters fail. Leads break. Ranges get left on the wrong setting. Batteries die. The industry rule that catches a failed instrument is PROVE–TEST–PROVE :
Step Action Purpose
1. PROVE Test the instrument on a known live source (or approved proving unit) Confirms the tester can detect voltage
2. TEST Test the circuit or equipment you intend to work on—all relevant conductors and between poles/earth as required Establishes de-energised state
3. PROVE Test the instrument again on the known live source / proving unit Confirms the tester still works after the circuit test
If step 1 fails, do not use the instrument. If step 2 shows voltage, the circuit is not isolated—find the remaining source. If step 3 fails, re-test the circuit with a proven instrument; you cannot trust a “dead” reading from a tester that no longer indicates live correctly.
Practical discipline
Use a suitable voltage tester or meter rated for the system and category of work.
Test phase-to-phase / active-to-active, active-to-neutral, and active-to-earth as appropriate so a single open neutral or missing earth reference does not fool you.
Do not skip the second prove because “it always works.” The second prove is what detects a tester that died during the dead test.
Test Before Touch
Test before touch means: before any conductive contact with conductors, terminals, or exposed conductive parts that might be live, verify absence of voltage by the prove–test–prove process (or equivalent competent method).
Do not treat the following as proof of isolation:
- Switch handle position alone
- A colleague’s verbal assurance without your verification
- A faded tag with no locked isolation point
- “It was off yesterday”
- Circuit labels that may be wrong after alterations
On the exam, answers that skip testing because “the main switch was down” are usually wrong. The main switch may feed only part of the installation; alternative supplies may still be present; the wrong circuit may have been operated.
Identify All Sources of Supply
Modern installations often have more than one energy source . Isolation of the “main switch” alone can leave the work point live or capable of becoming live.
Sources and backfeed paths to actively hunt for include:
- Source type Why it bites
- Utility / consumer mains Primary supply; multiple submains and distribution boards
- Standby generators May backfeed through changeover or manual links
- UPS / battery systems Maintain output after mains isolation
- PV / inverter systems DC arrays and AC inverter output; islanding and backfeed risks
- Parallel boards / interconnectors Second feed from another board or temporary supply
- Control supplies / foreign voltages Separate control transformers or imported signals
Identify → isolate each source → secure → prove dead at the point of work. If you cannot identify the supply architecture, stop and obtain drawings, labels, and site knowledge before opening enclosures.
PV and inverter awareness (high level)
Even when the AC isolator is open, PV modules can still produce hazardous DC in light. Isolation procedures for renewable systems must address both AC and DC sides per the installation design and applicable standards. Exam stems often reward “consider alternative and renewable sources,” not “main switch only.”
Written Isolation Procedures for Complex Sites
Simple single-board domestic isolation may be managed by a competent person with clear LOTO and prove–test–prove. Complex sites —hospitals, industrial plants, multi-board commercial buildings, sites with generators/UPS/PV—need written isolation procedures that define:
- Scope of work and equipment boundaries
- All isolation points and sequence of isolation
- Locks, tags, and who holds keys
- Test points and method (prove–test–prove)
- Residual energy (capacitors, batteries, mechanical)
- Communication with operators and permit-to-work interfaces where used
- Restoration sequence and who authorises re-energisation
Written procedures reduce reliance on memory under time pressure and make supervision of trainees auditable. For EWRB competence culture, treating complex isolation as “in my head only” is a red flag.
Exam habits
Always sequence identify sources → isolate → lock/tag → prove–test–prove → work .
Reject answers that treat switch position as sufficient without testing.
- Call out UPS, generator, and PV/backfeed whenever the stem is multi-source or “unexpectedly live.”
- Study note
Pair this section with LOTO (11.3) and live-work controls (11.4). Isolation without securing against re-energisation is incomplete; prove–test–prove without identifying all sources is incomplete.