Study guide
9.2 Continuity of Earthing & Protective Bonding
NZ EWRB Electrician Registration Regulations
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Open-Reference Strategy & Permitted Materials 1.3 Electrician Registration Pathway & Limits of Work 1.4 Which Editions Apply: ESR Schedule 2 & the 13 November 2025 Update
2 Electricity Act & EWRB Framework
2.1 Electricity Act 1992 Framework 2.2 EWRB Role, Register & Registration Classes 2.3 Practising Licence & Electrician Limits of Work
3 Electricity (Safety) Regulations 2010
3.1 ESR 2010 Structure & Key Definitions 3.2 Electrically Safe & Electrically Unsafe 3.3 Duties of Electrical Workers & Competence 3.4 Certification Timeframes & Notification Duties under ESR
4 Prescribed Electrical Work
4.1 What Is Prescribed Electrical Work 4.2 PEW Risk Categories: Low, General, High 4.3 Who May Carry Out and Supervise PEW 4.4 High-Risk Work & Electrical Inspector Requirements
5 Certification Documents (CoC, ESC, RoI)
5.1 Certificate of Compliance (Regulation 65) 5.2 Electrical Safety Certificate (Safe to Connect / Use) 5.3 Record of Inspection (Regulation 72) 5.4 Record-Keeping, Retention & the Certification Chain 5.5 Record-Keeping Duties & the Statutory Clocks (regs 72A, 74E–74H)
6 AS/NZS 3000 Fundamentals
6.1 Structure of AS/NZS 3000 & Open-Book Navigation 6.2 Multiple Earthed Neutral (MEN) System 6.3 Basic Protection vs Fault Protection 6.4 Protective Devices, Discrimination & Coordination
7 RCDs, Shock Protection & Disconnection Times
7.1 RCD Shock-Protection Requirements 7.2 RCD Types, Classification & Installation Contexts 7.3 Disconnection Times (0.4 s / 5 s) & Earth Fault Path 7.4 Damp Situations & Additional Protection
8 Circuits, Maximum Demand & Voltage Drop
8.1 Division of Circuits & Final Subcircuits 8.2 Maximum Demand Principles 8.3 Voltage Drop Requirements & Worked Examples
9 Testing & Verification Core
9.1 Visual Inspection Before Testing 9.2 Continuity of Earthing & Protective Bonding 9.3 Insulation Resistance Testing (500 V DC, 1 MΩ) 9.4 Polarity & Correct Circuit Connections
10 EFLI, RCD Tests & Verification Sequence
10.1 Earth Fault Loop Impedance 10.2 RCD Operation Tests & Prospective Fault Current 10.3 Mandatory Test Sequence & Documentation
11 Safe Isolation & Personal Safety
11.1 Physiological Effects of Current & Shock Factors 11.2 Prove–Test–Prove Safe Isolation 11.3 Lock-Out/Tag-Out & Safety Tag System 11.4 Live-Work Controls, Fault Finding & Unsafe Installations
12 Electrical Codes of Practice & Schedule 2
12.1 NZECP 34 Electrical Safe Distances 12.2 NZECP 50 Repair of Domestic Electrical Equipment 12.3 NZECP 51 Electrical Wiring Work in Domestic Premises 12.4 NZECP 54 Recessed Luminaires & Auxiliary Equipment 12.5 ESR Schedule 2 & Companion Standards Overview
13 Installation Requirements
13.1 Consumer Mains, Point of Supply & Switchboards 13.2 Conductor Identification, Isolation, Labelling & IP Ratings 13.3 Cable Selection (AS/NZS 3008.1.2 NZ Conditions) 13.4 Construction Sites, Appliance Testing & Special Installations 13.5 Periodic Assessment, Warrants of Electrical Fitness & AS/NZS 3019
14 Exam Strategy & Key Numbers
14.1 Must-Know Numbers, Times & Thresholds 14.2 Exam Tactics & Common Traps
9.2 Continuity of Earthing & Protective Bonding
Key Takeaways Explain This Topic AI
Earth continuity verifies protective earthing conductors and equipotential bonding form a continuous low-resistance path
Use an ohmmeter / continuity function on de-energised circuits; high resistance or open circuit is a fail
Include main earth, MEN link path, circuit PECs, and bonding to water pipes/structural steel as applicable
Failed continuity undermines automatic disconnection of supply (ADS) and raises shock risk on exposed metal
Continuity is a dead test that belongs before insulation resistance in the Section 8 sequence where appropriate
Last updated: August 2026
Purpose of the Continuity Test
After visual inspection, the next classic dead test is continuity of the protective earthing system and equipotential bonding (AS/NZS 3000 region 8.3.5 —confirm in your permitted edition). The question this test answers is simple and non-negotiable:
Is there a continuous, low-resistance metallic path from every required earthed/bonded part back through the protective earthing network to the main earthing point / MEN arrangement?
If that path is open, high-resistance, or misconnected, fault protection by automatic disconnection of supply (ADS) is compromised. Exposed conductive parts can remain at dangerous potential under fault conditions because fault current cannot return reliably through the intended earth–neutral path.
AS/NZS 3017 elaborates practical probe points, instrument technique, and interpretation consistent with Section 8 outcomes. Exam stems test the principle and sequence more than brand-specific meter menus.
What Must Be Continuous
Think of continuity as a network, not a single wire.
Protective earthing conductors (PECs)
Continuity from each circuit’s earthing conductor (socket earth pins, switchboard earth bar tails, fixed-equipment earth terminals) back to the earth bar / main earthing point
- No reliance on random metalwork that is not intentional protective earthing
- Main earth and MEN link path
- Continuity of the main earthing conductor to the electrode connection (as applicable)
Integrity of the path that includes the MEN link at the main switchboard main earthing point—visual presence of a link is necessary but not sufficient; the related conductors must also be continuous and tight
No “open MEN” discovered only after energising if a dead continuity check could have caught a disconnected link or floating earth bar tail
Equipotential bonding
As applicable to the installation:
Bonding to water pipes , other service pipes, and structural steel or other extraneous conductive parts required to be bonded
Continuity through bonding clamps and intermediate joints—painted, corroded, or isolated pipe sections can create open bonds that look fine until measured
Bonding limits potential differences between simultaneously accessible parts; it does not replace protective earthing, the MEN link, or ADS design. Continuity testing proves the bond is actually a conductor, not a decorative clamp.
- Instrument Method
- Dead test, low-resistance expectation
- Prove the circuit/installation section is de-energised and safe to work on before connecting the instrument
- Use an ohmmeter or the continuity function of a multifunction installation tester
Expect a low resistance reading for a continuous path; an open circuit or unexpectedly high resistance is a fail until the joint, conductor, or connection is corrected and retested
Exact maximum continuity resistance values and any length/csa-dependent expectations must be taken from your permitted AS/NZS 3000 / 3017 text for the sitting. For exam strategy, prioritise: continuous + low resistance = pass path; open/high = defect .
Practical technique points (exam-relevant)
Test from accessible equipment earth points and bonding points back to the earth bar / main earthing point as appropriate
Account for parallel paths that can mask a broken intended conductor—interpretation skill matters when metalwork provides an alternative route
- Include both circuit PECs and main/bonding paths in a complete verification story
- Fail Implications: ADS and Shock Risk
- Continuity outcome Safety meaning
- Continuous low-R earth/bond path Fault current and equipotential control can work as designed
Open or high-R earth conductor Exposed metal may stay live under fault; overcurrent device may not operate in time
- Open bonding Dangerous touch voltage between services/metalwork during a fault
- Broken MEN-related path Earth-fault return via neutral path degraded—classic ADS failure mode
RCDs may still trip on residual current in some fault scenarios, but RCD presence does not excuse open protective earthing . Continuity failures remain serious non-compliance and shock risk.
Sequence: Dead Continuity Before Insulation (Where Appropriate)
EWRB Toolbox order after visual inspection:
- Earth continuity (8.3.5)
- Insulation resistance (8.3.6)
- Polarity (8.3.7)
- Correct connections (8.3.8)
- Then live tests (EFLI 8.3.9, RCD 8.3.10)
Why continuity early?
It is a dead test that proves the safety earthing network before applying IR test voltage and before energising
Finding an open earth after energising is late discovery of a fault that should have been caught cold
IR tests between live conductors and earth assume you understand the earth reference path; continuity establishes that the earth system is joined
- Exam traps
- Treating continuity as “optional if IR is high”
Confusing continuity ohms with insulation resistance megohms (different instruments, opposite desired magnitude)
- Thinking bonding continuity replaces the need for circuit PECs or MEN integrity
- Jumping to EFLI on a live board when earthing continuity has not been established
- Study note
On a mental main switchboard sketch, trace: earth bar → main earthing conductor → electrode; MEN link to neutral; outgoing PECs to sockets; bonds to water/steel. Continuity testing is how you prove that sketch is real metal, not hope.