Study guide
9.3 Insulation Resistance Testing (500 V DC, 1 MΩ)
NZ EWRB Electrician Registration Regulations
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Open-Reference Strategy & Permitted Materials 1.3 Electrician Registration Pathway & Limits of Work 1.4 Which Editions Apply: ESR Schedule 2 & the 13 November 2025 Update
2 Electricity Act & EWRB Framework
2.1 Electricity Act 1992 Framework 2.2 EWRB Role, Register & Registration Classes 2.3 Practising Licence & Electrician Limits of Work
3 Electricity (Safety) Regulations 2010
3.1 ESR 2010 Structure & Key Definitions 3.2 Electrically Safe & Electrically Unsafe 3.3 Duties of Electrical Workers & Competence 3.4 Certification Timeframes & Notification Duties under ESR
4 Prescribed Electrical Work
4.1 What Is Prescribed Electrical Work 4.2 PEW Risk Categories: Low, General, High 4.3 Who May Carry Out and Supervise PEW 4.4 High-Risk Work & Electrical Inspector Requirements
5 Certification Documents (CoC, ESC, RoI)
5.1 Certificate of Compliance (Regulation 65) 5.2 Electrical Safety Certificate (Safe to Connect / Use) 5.3 Record of Inspection (Regulation 72) 5.4 Record-Keeping, Retention & the Certification Chain 5.5 Record-Keeping Duties & the Statutory Clocks (regs 72A, 74E–74H)
6 AS/NZS 3000 Fundamentals
6.1 Structure of AS/NZS 3000 & Open-Book Navigation 6.2 Multiple Earthed Neutral (MEN) System 6.3 Basic Protection vs Fault Protection 6.4 Protective Devices, Discrimination & Coordination
7 RCDs, Shock Protection & Disconnection Times
7.1 RCD Shock-Protection Requirements 7.2 RCD Types, Classification & Installation Contexts 7.3 Disconnection Times (0.4 s / 5 s) & Earth Fault Path 7.4 Damp Situations & Additional Protection
8 Circuits, Maximum Demand & Voltage Drop
8.1 Division of Circuits & Final Subcircuits 8.2 Maximum Demand Principles 8.3 Voltage Drop Requirements & Worked Examples
9 Testing & Verification Core
9.1 Visual Inspection Before Testing 9.2 Continuity of Earthing & Protective Bonding 9.3 Insulation Resistance Testing (500 V DC, 1 MΩ) 9.4 Polarity & Correct Circuit Connections
10 EFLI, RCD Tests & Verification Sequence
10.1 Earth Fault Loop Impedance 10.2 RCD Operation Tests & Prospective Fault Current 10.3 Mandatory Test Sequence & Documentation
11 Safe Isolation & Personal Safety
11.1 Physiological Effects of Current & Shock Factors 11.2 Prove–Test–Prove Safe Isolation 11.3 Lock-Out/Tag-Out & Safety Tag System 11.4 Live-Work Controls, Fault Finding & Unsafe Installations
12 Electrical Codes of Practice & Schedule 2
12.1 NZECP 34 Electrical Safe Distances 12.2 NZECP 50 Repair of Domestic Electrical Equipment 12.3 NZECP 51 Electrical Wiring Work in Domestic Premises 12.4 NZECP 54 Recessed Luminaires & Auxiliary Equipment 12.5 ESR Schedule 2 & Companion Standards Overview
13 Installation Requirements
13.1 Consumer Mains, Point of Supply & Switchboards 13.2 Conductor Identification, Isolation, Labelling & IP Ratings 13.3 Cable Selection (AS/NZS 3008.1.2 NZ Conditions) 13.4 Construction Sites, Appliance Testing & Special Installations 13.5 Periodic Assessment, Warrants of Electrical Fitness & AS/NZS 3019
14 Exam Strategy & Key Numbers
14.1 Must-Know Numbers, Times & Thresholds 14.2 Exam Tactics & Common Traps
9.3 Insulation Resistance Testing (500 V DC, 1 MΩ)
Key Takeaways Explain This Topic AI
Classic LV values: insulation resistance tested at 500 V DC with a minimum acceptable reading of 1 MΩ (confirm in permitted AS/NZS 3000 Section 8 edition)
Test between live conductors and earth, and between actives as applicable; isolate/disconnect sensitive electronic equipment
Low readings often mean moisture, damaged insulation, or still-connected loads/devices—not always a permanent cable fault
Safety: prove dead before testing and discharge capacitance after applying DC test voltage
- Exam trap: do not confuse IR minimum (1 MΩ) with RCD residual current ratings (e.g. 30 mA)
- Last updated: August 2026
Classic Values Candidates Must Own
For typical low-voltage installations (nominal circuits in the common 230/400 V range), AS/NZS 3000 Section 8 verification teaches two numbers that appear constantly in EWRB preparation material, exam-meta key stats, and practice banks:
- Parameter Classic value
- IR test voltage 500 V DC
- Minimum insulation resistance 1 MΩ
Confirm exact application ranges, any exceptions, and wording in the permitted edition of AS/NZS 3000 for your Aspeq sitting. Higher test voltages (e.g. 1000 V DC) belong to higher circuit voltage categories—not the default domestic/commercial LV story. Lower values such as 0.5 MΩ are not the standard minimum taught for this pathway.
These figures sit in the dead-test block after earth continuity ( 8.3.6 region) and before polarity/correct-connection checks, still before energised EFLI and RCD tests.
What the Test Measures
An insulation resistance tester (megohmmeter) applies a controlled DC voltage and measures resistance of the insulation system. Desired results are high (megohms), the opposite of continuity testing’s low-ohm goal.
Typical test combinations
Between live conductors and earth — actives (and neutral where the method requires) referenced to the protective earthing system
Between actives (and other live–live combinations) as applicable to the circuit arrangement and the method in AS/NZS 3000 / 3017
The goal is to show insulation is intact enough that leakage under test voltage is acceptably low before the installation is put into service or re-energised after PEW.
Care with electronic equipment
Disconnect or isolate sensitive gear before applying 500 V DC:
Electronic ballasts, dimmers, surge protective devices, control electronics, and many modern appliances can be damaged by IR test voltage
Connected loads and electronics can also produce falsely low readings that look like insulation failure when the wiring is fine
Open links, remove loads, or isolate equipment so the reading reflects installation wiring insulation , not the internal paths of connected devices—unless the procedure deliberately includes them (exam stems almost always want isolation of sensitive equipment).
Interpreting Low Readings
A reading below 1 MΩ (or trending unexpectedly low) is a stop-and-investigate result, not a “nearly pass.” Common causes:
- Cause Why IR drops
- Moisture Damp cables, enclosures, or terminations increase leakage
- Damaged insulation Nicks, crush, heat damage, UV, rodent attack
- Connected loads / electronics Internal paths or protective devices skew the result
- Contamination Conductive dust, corrosion, tracking across surfaces
- Wrong test setup Incomplete isolation, probes on wrong points, parallel circuits still connected
Do not energise and hope. Dry, repair, disconnect, or re-terminate as required; then retest until the installation meets the minimum and makes engineering sense.
Safety: Prove Dead and Discharge
Insulation testing is performed on a de-energised installation section.
Prove dead with a proven testing process before connecting the IR tester—never apply a megohmmeter to a live circuit “to save time.”
Apply the specified DC test voltage using a suitable instrument.
After the test, discharge capacitance in cables and equipment. Long cable runs store charge after high-voltage DC testing; leave residual charge and the next person to touch the conductors may receive a shock or damage other equipment.
AS/NZS 3017 guidance emphasises correct instrument use and safe method; treat discharge as part of professional IR practice, not optional etiquette.
Exam Trap: IR MΩ vs RCD mA
Candidates routinely mix units and purposes:
- Concept Typical teaching number Unit / meaning
- Insulation resistance minimum 1 MΩ at 500 V DC High resistance of insulation
- RCD shock protection 30 mA residual rating Trip sensitivity in milliamps
- RCD trip times 300 ms @ 1× / 40 ms @ 5× (classic teaching) Operating time under test current
Wrong polarity of thinking: “RCD is 1 mA” or “IR must be 30 MΩ because of 30 mA RCDs.” Keep megohms for insulation and milliamps for residual current in separate mental drawers.
Sequence reminder
Visual → continuity → IR → polarity → correct connections → (later) EFLI → RCD. IR is still a dead test. Passing IR does not replace continuity, polarity, or live functional tests.
When IR fails, do not “skip to live tests”
A sub-minimum IR result means the installation is not ready for energisation for EFLI or RCD operation tests. Live testing on wiring with known insulation failure risks further damage, nuisance trips that hide the real fault, and shock/fire hazards. The competent path is: isolate, diagnose, repair or dry out, retest IR to ≥ 1 MΩ , then continue the sequence. Certification evidence should show that insulation was proven before service connection decisions that depend on verification.
AS/NZS 3017 remains the practical methods companion—probe technique, instrument selection, and safe application of DC test voltage—while AS/NZS 3000 Section 8 states the verification requirement and acceptance outcome. On open-book stems, open Section 8 for “what must be achieved,” and use 3017 thinking for “how the test is performed safely.”
Study note
Memorise for speed: 500 V DC, ≥ 1 MΩ , disconnect electronics, prove dead, discharge after. Open Section 8 IR clauses in your permitted book once so clause geography matches the numbers you already know. Drill the unit trap until automatic: MΩ = insulation; mA = RCD.