Study guide

10.3 Mandatory Test Sequence & Documentation

NZ EWRB Electrician Registration Regulations

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Open-Reference Strategy & Permitted Materials 1.3 Electrician Registration Pathway & Limits of Work 1.4 Which Editions Apply: ESR Schedule 2 & the 13 November 2025 Update

2 Electricity Act & EWRB Framework

2.1 Electricity Act 1992 Framework 2.2 EWRB Role, Register & Registration Classes 2.3 Practising Licence & Electrician Limits of Work

3 Electricity (Safety) Regulations 2010

3.1 ESR 2010 Structure & Key Definitions 3.2 Electrically Safe & Electrically Unsafe 3.3 Duties of Electrical Workers & Competence 3.4 Certification Timeframes & Notification Duties under ESR

4 Prescribed Electrical Work

4.1 What Is Prescribed Electrical Work 4.2 PEW Risk Categories: Low, General, High 4.3 Who May Carry Out and Supervise PEW 4.4 High-Risk Work & Electrical Inspector Requirements

5 Certification Documents (CoC, ESC, RoI)

5.1 Certificate of Compliance (Regulation 65) 5.2 Electrical Safety Certificate (Safe to Connect / Use) 5.3 Record of Inspection (Regulation 72) 5.4 Record-Keeping, Retention & the Certification Chain 5.5 Record-Keeping Duties & the Statutory Clocks (regs 72A, 74E–74H)

6 AS/NZS 3000 Fundamentals

6.1 Structure of AS/NZS 3000 & Open-Book Navigation 6.2 Multiple Earthed Neutral (MEN) System 6.3 Basic Protection vs Fault Protection 6.4 Protective Devices, Discrimination & Coordination

7 RCDs, Shock Protection & Disconnection Times

7.1 RCD Shock-Protection Requirements 7.2 RCD Types, Classification & Installation Contexts 7.3 Disconnection Times (0.4 s / 5 s) & Earth Fault Path 7.4 Damp Situations & Additional Protection

8 Circuits, Maximum Demand & Voltage Drop

8.1 Division of Circuits & Final Subcircuits 8.2 Maximum Demand Principles 8.3 Voltage Drop Requirements & Worked Examples

9 Testing & Verification Core

9.1 Visual Inspection Before Testing 9.2 Continuity of Earthing & Protective Bonding 9.3 Insulation Resistance Testing (500 V DC, 1 MΩ) 9.4 Polarity & Correct Circuit Connections

10 EFLI, RCD Tests & Verification Sequence

10.1 Earth Fault Loop Impedance 10.2 RCD Operation Tests & Prospective Fault Current 10.3 Mandatory Test Sequence & Documentation

11 Safe Isolation & Personal Safety

11.1 Physiological Effects of Current & Shock Factors 11.2 Prove–Test–Prove Safe Isolation 11.3 Lock-Out/Tag-Out & Safety Tag System 11.4 Live-Work Controls, Fault Finding & Unsafe Installations

12 Electrical Codes of Practice & Schedule 2

12.1 NZECP 34 Electrical Safe Distances 12.2 NZECP 50 Repair of Domestic Electrical Equipment 12.3 NZECP 51 Electrical Wiring Work in Domestic Premises 12.4 NZECP 54 Recessed Luminaires & Auxiliary Equipment 12.5 ESR Schedule 2 & Companion Standards Overview

13 Installation Requirements

13.1 Consumer Mains, Point of Supply & Switchboards 13.2 Conductor Identification, Isolation, Labelling & IP Ratings 13.3 Cable Selection (AS/NZS 3008.1.2 NZ Conditions) 13.4 Construction Sites, Appliance Testing & Special Installations 13.5 Periodic Assessment, Warrants of Electrical Fitness & AS/NZS 3019

14 Exam Strategy & Key Numbers

14.1 Must-Know Numbers, Times & Thresholds 14.2 Exam Tactics & Common Traps

10.3 Mandatory Test Sequence & Documentation

Key Takeaways Explain This Topic AI

EWRB Toolbox / AS/NZS 3000 order: visual → continuity → IR → polarity → correct connections → (live) EFLI + RCD; reconfirm polarity/connections live if needed

Pre-livening checklist: MEN restored, visual recheck, dead tests satisfactory before energising

Record results as CoC/certification evidence—verification without records is incomplete practice

All PEW must be tested as applicable: repairs, additions, mains, special installations—not only new full builds

  • AS/NZS 3017 is the methods companion to Section 8; failures mean do not certify—remediate and retest
  • Last updated: August 2026

Full EWRB Recommended Verification Sequence

Section 8 is a process , not a menu of optional meter tricks. The EWRB Toolbox and AS/NZS 3000 verification structure align on this order (clause numbers confirm in your permitted edition):

  • Step Activity Typical clause region Live/dead
  • 1 Visual inspection 8.2 / checklist 8.2.2 Dead
  • 2 Earth continuity & protective bonding 8.3.5 Dead
  • 3 Insulation resistance 8.3.6 Dead
  • 4 Polarity 8.3.7 Dead (as method allows)
  • 5 Correct circuit connections 8.3.8 Dead
  • 6 Earth fault loop impedance 8.3.9 Live
  • 7 RCD operation 8.3.10 Live

Where methods require, reconfirm polarity or connections under live conditions after energisation—never as a substitute for the dead-test block. The point of sequence is safety and validity : do not apply IR test voltage or energise for EFLI/RCD until the installation is suitably complete, continuous, and insulated.

  • Why order matters
  • Visual defects (missing MEN, open barriers) are caught before instruments create a false sense of security
  • Continuity establishes the earthing network before IR references earth and before live fault-loop tests
  • IR failures must be fixed before livening

Polarity and correct connections prevent energising circuits that leave neutrals switched or actives transposed

  • Live EFLI and RCD tests assume the dead foundation is true
  • Pre-Livening Checklist

Before operating the main switch for live verification:

MEN link restored and verified present at the main earthing point (visual + related continuity evidence)

Visual recheck — covers on, barriers intact, no temporary leads left as permanent, labels and isolators identifiable

Dead tests satisfactory — continuity, IR (≥ 1 MΩ at 500 V DC classic LV teaching), polarity, correct connections as applicable to the PEW

Work area controlled — other persons protected; prove-test discipline for any isolation still in play

Instrument readiness — correct functions for EFLI, RCD, and PFC/PSCC as required; leads and PE connections sound

Skipping pre-livening checks to “save time” is a classic exam wrong answer and a real-world shock/fire risk.

Record Results for CoC / Certification Evidence

Verification is inseparable from certification competence under the Electricity (Safety) Regulations and EWRB expectations:

Record what was tested, where , with what results , and pass/fail against criteria

Retain records that support Certificate of Compliance , electrical safety certification, and inspection trails as applicable to the work

  • Note instrument identity/calibration awareness as professional practice requires
  • Document defects , remediation, and retest outcomes—not only the final green tick

A CoC that asserts compliance while verification was incomplete, unrecorded, or failed-and-ignored is not defensible. The exam rewards answers that couple sequence + records + refuse-to-certify-on-fail .

All PEW Must Be Tested

Verification is not limited to brand-new whole-house rewires:

  • Work type Verification expectation
  • New installations Full applicable Section 8 sequence

Additions / alterations Test the PEW and its interfaces so the addition is safe and does not degrade existing protection

  • Repairs Test as required to prove the repaired portion is electrically safe
  • Mains / switchboard work High impact on MEN, earthing, PFC, and upstream protection—rigorous verification

Special installations Apply Section 8 plus any extra standard requirements (e.g. construction sites, medical, hazardous—as taught)

“I only moved one socket” is not a free pass out of polarity, continuity, IR, and RCD checks as applicable. Scale the tests to the PEW; do not invent a zero-test category for convenience.

AS/NZS 3017 as Methods Companion

  • Standard Role
  • AS/NZS 3000 Section 8 Mandatory verification requirements and acceptance outcomes
  • AS/NZS 3017 Electrical installations—verification guidelines: methods, instruments, practical technique

On open-book stems: open 3000 for what must be achieved and in what order ; use 3017 thinking for how to perform the test safely . 3017 does not replace Section 8 duties.

Failures: Do Not Certify — Remediate and Retest

  • Outcome Required action
  • Visual non-compliance Fix construction; re-inspect
  • Continuity / IR / polarity / connections fail Diagnose, repair, retest dead
  • EFLI too high Find high-R joints, length/CSA issues, bonding faults; retest live
  • RCD fails trip time/type/rating Replace or correct installation; retest
  • Incomplete records Complete documentation before treating work as certified

Never sign or issue certification on the basis of failed or omitted mandatory tests. The competent path is: stop → remediate → retest → record → then certify if compliant.

  • Exam traps
  • Live tests first “because the board is already on”
  • Certifying after a failed IR “because RCD tripped OK”
  • Treating 3017 as optional folklore instead of the methods companion
  • Testing only new circuits and ignoring PEW on repairs/additions
  • Study note

Commit the seven-step sequence to automatic recall. Drill: MEN on before live tests; records for CoC; fail = fix + retest . Flag Section 8 contents pages and keep AS/NZS 3017 in your mental toolkit beside 3000 for method questions.