Study guide

7.1 Certifying Authority, Producer Statements & Records of Work

NZ PGDB Certifying Drainlayer Registration Examination Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Foul-Water Drainage System Design

1.1 Separated Drainage Systems & Cross-Connection Prevention 1.2 Drain Layout, Junctions, Bends & Sweep Connections 1.3 Gully Traps, Water Seals & Overflow Relief Gullies (ORG) 1.4 Boundary Connections, Inspection Shafts & Public Sewer Interface

2 Chapter 2: Drainage Ventilation & Commercial Waste Systems

2.1 Drainage Ventilation Systems, Relief Vents & Air Admittance Valves (AAVs) 2.2 Discharge Unit & Fixture Unit Sizing under G13/AS2 & AS/NZS 3500.2 2.3 Commercial Grease Interceptors & Oil/Grit Separators 2.4 Pumped Drainage Systems, Sumps & Rising Mains

3 Chapter 3: Stormwater Drainage & Surface Water Management

3.1 Stormwater Sizing & Flow Calculations to AS/NZS 3500.3 & E1/AS1 3.2 Stormwater Pits, Sumps, Silt Traps & Inlets 3.3 Soakage Systems, Retention & Detention Tanks 3.4 Overland Flow Paths & Secondary Flow Protection

4 Chapter 4: Drainage Testing & Quality Verification

4.1 Hydrostatic (Water) Testing Methods & Pressure Limits 4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection 4.3 CCTV Inspection, Defect Identification & As-Built Verification

5 Chapter 5: Trenching Safety & Confined Spaces

5.1 Excavation & Trenching Safety: Shoring, Battering & Benching 5.2 Confined Space Entry, Atmospheric Monitoring & Hazardous Gases 5.3 Underground Service Locating & Utility Strike Prevention 5.4 Site Health & Safety Management under the Health and Safety at Work Act 2015

6 Chapter 6: The Legislative & Regulatory Framework

6.1 Plumbers, Gasfitters, and Drainlayers Act 2006 & Board Functions 6.2 Licensing Classes, Registration Competencies & Annual Practising Licences 6.3 Disciplinary Regime, Offences, Complaints & Board Powers

7 Chapter 7: Certifying Drainlayer Authority & Site Supervision

7.1 Certifying Authority, Producer Statements & Records of Work 7.2 Supervision Principles: Direct vs General Supervision & Trainee Ratios 7.3 Professional Ethics, Continuing Professional Development (CPD) & Quality Assurance

8 Chapter 8: On-Site Wastewater System Design

8.1 AS/NZS 1547 Framework, Site Assessment & Soil Classification 8.2 Primary Treatment: Septic Tank Sizing, Baffles & Effluent Filters 8.3 Secondary Treatment: Aerated Wastewater Treatment Systems (AWTS) & Media Filters

9 Chapter 9: Land Application Systems & Environmental Protection

9.1 Land Application Systems: Absorption Trenches, Beds & Subsurface Drip Irrigation 9.2 Design Loading Rates (DLR), Reserve Areas & Hydraulic Sizing 9.3 Environmental Setbacks, Groundwater Protection & Resource Consents

10 Chapter 10: Pipe Materials, Jointing & Transitions

10.1 DWV Pipe Materials: uPVC, Vitrified Clay, PE & Concrete 10.2 Jointing Technologies: Solvent Cementing & Rubber Ring Joints 10.3 Dissimilar Material Adaptors, Flexible Couplings & Expansion Management

11 Chapter 11: Trench Bedding, Support & Backfill

11.1 Bedding Classes & Material Specifications under AS/NZS 3500.2 11.2 Cover Depths, Loading Conditions & Encasement Protection 11.3 Trench Backfill, Compaction Standards & Pipe Flotation Prevention

12 Chapter 12: Gradients, Invert Levels & Setting Out

12.1 Gradient Standards & Self-Cleansing Velocities under G13 & AS/NZS 3500.2 12.2 Fall, Grade & Run Calculations 12.3 Invert Level Calculations & Datum Relationships 12.4 Setting Out Methods: Laser Levels, Optical Instruments & Boning Rods

13 Chapter 13: Building Code Compliance & Service Separation

13.1 NZ Building Code Architecture: Clause G13, Clause E1 & Compliance Pathways 13.2 Service Separation: Clearances Between Foul Water, Stormwater & Other Utilities 13.3 Building Consent Authorities (BCAs), Code Compliance Certificates (CCC) & Council Inspections

14 Chapter 14: Examination Blueprint & Integrated Certifying Practice

14.1 Official Examination 9198 Blueprint, Logistics & Source Strategy 14.2 Plans, Specifications, Material Lists, Patterns, Tools & Equipment 14.3 Sustainability, Water Quality, Structural Integrity, Seismic & Geotechnical Resilience

7.1 Certifying Authority, Producer Statements & Records of Work

Key Takeaways Explain This Topic AI

Certifying registration and a current licence do not automatically include the self-certification endorsement.

From 7 September 2026, eligible consented work may be self-certified only by a certifying practitioner holding the specific endorsement and meeting its conditions.

Producer statements are evidence used by some BCAs; they are not statutory licences and are not universally required.

Documentation must state what was observed, tested, designed, or relied upon.

Last updated: October 2026

Certifying authority and documentation

A certifying drainlayer is responsible for their own work and for adequate supervision of restricted work carried out under their authority. Documentation should make that responsibility visible without claiming powers the practitioner does not hold.

Ordinary certifying authority

The certifying class is the highest drainlaying registration class. With a current practising licence, the practitioner may perform the work within scope and supervise others as permitted by the Act. The certifier must know the work, direct and monitor it at a level suited to the person and risk, inspect critical stages, and verify the finished result.

This authority is not a general power to certify any drainage project. Public-network approvals, building consent, resource consent, specialist design, and the Building Code remain applicable.

Self-certification endorsement

From 7 September 2026, the statutory self-certification scheme permits eligible consented work to be self-certified only by a certifying plumber or drainlayer who holds the specific self-certification endorsement. The Board’s current application material requires a current certifying licence, completion of the prescribed training, appropriate insurance, business systems and records, and payment of the applicable fee and audit levy.

A certifying-drainlayer licence without that endorsement is not self-certification authority. The endorsement also does not make every project eligible. Check the Act, regulations, Board conditions, eligible-work definition, consent documents, and audit obligations before using the pathway.

Records of work and project evidence

The current Act includes record-of-work provisions introduced by the recent amendments. Use the Board’s current form and directions for when, by whom, and to whom a record must be provided. Do not substitute an obsolete Building Act section or a locally invented certificate.

Project evidence may include approved plans and variations, site instructions, licence and supervision records, product data, inspection photographs, levels, test sheets, as-built drawings, network approvals, commissioning reports, and maintenance information. Each item has a purpose; a photograph does not prove a pressure test, and a test does not prove gradient.

Producer statements

Producer statements are commonly used as supporting evidence in New Zealand building-control practice, but they are not themselves a universal statutory licence, certificate, or mandatory form for every drain. A BCA decides what evidence it will consider on reasonable grounds, subject to the consent and its procedures. Sign a PS3 or similar statement only if requested or accepted and only within the signer’s competence and direct knowledge.

Honest scope

Write what was actually done. “I inspected the open trench on these dates and witnessed this named test” is stronger than “all work guaranteed compliant” when part of the system was outside the certifier’s observation. Identify reliance on a designer, surveyor, laboratory, treatment-unit technician, or network approval.

Documentation review

For a gravity drain, the closeout file might contain the consented plan, authorised variation for a reroute, supervision log, open-trench photographs, G13 test sheet, invert survey, as-built plan, and BCA inspection record. For an on-site treatment system, add the site-and-soil assessment, design report, regional or district approvals, commissioning data, owner manual, and maintenance agreement where required.

If a document contains an error, correct it transparently. Preserve version history and explain the change rather than silently altering the original. Good records enable the BCA, owner, supervisor, and future drainlayer to understand the installed system.

Independent source-check exercise

For 7.1 Certifying Authority, Producer Statements & Records of Work , practise answering from evidence rather than recall. Write the controlling source, its edition or effective date, its scope, and the exact paragraph, table, figure, or manufacturer instruction that supports the decision. Then state the site inputs that can change the result. In this section those inputs include Certifying registration and a current licence do not automatically include the self-certification endorsement.; From 7 September 2026, eligible consented work may be self-certified only by a certifying practitioner holding the specific endorsement and meeting its conditions.; Producer statements are evidence used by some BCAs; they are not statutory licences and are not universally required..

Build a four-column check: proposed condition, source requirement, evidence observed, and action. Test the answer with one changed assumption. A different pipe size, discharge-unit load, ground condition, licence status, authority, compliance path, or consent condition may produce a different result. If it does, explain why; if it does not, show which requirement remains controlling.

Finish with a field-verification plan. Name what must be inspected before concealment, what instrument or record demonstrates it, who has authority to accept a change, and what appears on the as-built or completion file. This exercise turns an open-book fact into certifying-level judgement. It also exposes accidental mixing of standards: if the source for a dimension differs from the source for the test or approval, either return to one complete compliance path or document the proposal as an Alternative Solution. Do not promote an example value into a national rule.

Loading diagram... Evidence chain